Farmall Super A, AV, 1939 - 1954
Moderator: Team Cub
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Anyone know how to remove item #30 on page 166, The Transmission Drive Flange?:
I am trying to replace the Transmission Spline Shaft Oil Seal, #27, and I have removed the center bolt, there is a key, but it does NOT want to come off. Tried prying and a puller (moved about 1/8"), but don't want to break the flange.
Next question: Anyone know where I can get a set of Clutch Drive Shaft Joint Rubber Washers (8), #14 page 163?
I split my SA & I REALLY want to get him back together again. Any help would be greatly appreciated!
Last edited by Dale Finch on Thu Oct 20, 2011 9:50 pm, edited 1 time in total.
As I recall, the flange is held on by a cap screw into the end of the shaft (listed unter reference 20, the shaft). Once you have the cap screw and washer off, you probably will need to replace the capscrew with a longer one (7/16 fine thread) and use a puller that is bolted through the holes in the drive flange. The puller set-up would be similar to that used on the front crank pulley, only smaller and probably easier. A steering wheel puller would probably pop it right off.
Last I knew the rubber washers were still available from CaseIH.
I came in this morning determined to get this thing off!! I was able to get the mechanic next door (bribed with lunch!) to come over and help me. I had been on the right track (almost what you suggested, Jim) and with his finess (an unusual aspect in most male mechanics I know!!) we used a substitute bolt with a recessed head (to keep the puller center screw from slipping off) and added a set of vice grips to squeeze and hold the puller arms on the recess behind the flange. It worked like a champ!
I do have another question for anyone: The Rubber Washers (#14 page 163 http://www.cleancomputes.com/Cub/Super%20A%20-%20Super%20AV/TC-39B%20Parts%20Catalog/Page%20163.jpg) are no longer available from IH.
Mine do need to be replaced. Anyone know if they are available from anyone else, or if there is a substitute product? They are about 1/4" thick and 1 1/8" in diameter and sit inside a metal retainer (one above is missing from its retainer). I am checking a rubber and gasket company tomorrow...we'll see...
Did you replace any of the seals before you painted it ?
IN GOD WE TRUST
All others pay cash
Power corrupts; absolute power corrupts absolutely byJohn Emerich Edward Dalberg
8th Va fest link viewtopic.php?f=8&t=81392&p=657790#p657790
I think I have now replaced every seal except the front engine seal (which IS leaking a tad) and the governor seal (which I rebuilt but thought the seal was OK). I have rebuilt the PTO and belt pulley, both finals (plus differential seals), rear engine seal, and now front transmission seal. Oh yeah, I did not replace (yet!!) the distributor/governor seal, either. Not sure why...
Looking good Dale!
It will be time to start over replacing the seals before long.. Hey, just kidding!
Thanks for the updates, I have enjoyed following the progress,
At the rate that I am taking things back apart, it'll be time for a new paint job, too!!! Oil pan next...!
I was going to do a nice How To for the transmission, but since I am now stopped by these stupid washers, I will wait 'til I am finished. I tried using a hole saw to cut a circle out of a tire side wall (suggested by the Service Manager/mechanic for the local IH shop). I think it would work, but can't find a hole saw the right diameter, ~ 1 1/16 - 1 1/8". Hopefully I will get lucky with this Rubber/Gasket company tomorrow. If I am able to get some, anyone else want any? The SA uses 8 for the assembly.
Dale, Messick's doesn't show them as available, but you might want to give them a call anyway:
http://www.messicks.com/partsearch.aspx ... 0d&ven=cas
Edit: I can't get the correct link to copy, but it shows them at $2.38. Type in the part # and you'll see it.
"We don't need to think more,
we need to think differently."
Looking good Dale, thanks for the updates enjoy the progress! Pabst
Dale - check out the possibility of rubber bushings such as the ones used to attach truck bodies to the chassis. You may be able to slice sections out of one of them if you find the right diameter. Auto parts stores would be a good source.\
Check out this link: http://www.casertainc.com/index.html
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
I think most body bushings will be too big. How about radiator mounting pads?
I called Messick's today, was real excited when I saw they listed them and a good price. But, alas, they did NOT have them, and after checking several alternate sources she had, she said no go. I couldn't believe NOBODY has replaced these things!
I plan to go to NAPA tomorrow and see if we can brainstorm something.
Good idea!! I will dig out a couple of the old ones I removed from the SA and see if they are the right thickness and if they can be cut. If so, I will order some new ones.
Thanks all for the suggestions!
YEA!! Someone suggested a place in Raleigh that might be able to make the flange washers I need. So I dashed off there and showed them the washers and they said SURE!! I waited 20-30 minutes and...TA DA! I had 2 sets of 8 beautiful Buna Rubber washers!
While I was there, I asked if they could duplicate the fuel strainer washer I had just purchased for about $4 from IH, after buying a couple cork ones that leaked like a sieve! They said SURE!! And a few minutes later I had 10 new rubber gaskets!
I am VERY HAPPY today! Hopefully tomorrow will be a good day as well, and I will get Bubba put back together (again!). Of course, I still have to thread that looong drive shaft back into the engine......hmmmmm.....oh dear.....!
Have a good night, all!
Well, Dale, since I have relatives in that area, you need to reveal your source, of course.
In the middle of every difficulty lies opportunity. - Albert Einstein
Deep South CubFest
February 13 & 14, 2015
It is Raleigh Durham Rubber and Gaskets, 919-781-6817. I have their address but it is at the shop, if you need it. They have all sorts of stuff, and are really nice. The owner of the shop uses them a lot. If you need something, just let me know.
Who is online
Users browsing this forum: No registered users and 2 guests