Bad Boy ZTR

Anything that might not belong on the other message boards!

Moderator: Team Cub

Forum rules
1. Keep it clean.
2. Keep the discussion civil.
3. Name calling is not allowed.

Politics and religion are two topics that tend to degenerate into a violation of one of the three simple rules above.

The mods and the site admin reserve the right to "lock" or "delete" any discussion that in our opinion, is "heading in the wrong direction."

MOST of all, be respectful of your fellow Cubber's opinions. Don't expect to change someones belief system from a simple forum on the internet.

Bad Boy ZTR

Postby Billy Fussell » Fri May 18, 2012 9:23 am

Has anyone had any experience, good or bad, with Bad Boy ZTR's? I have been looking at them and kinda like the looks of them.

Billy
Billy Fussell
501 Club
501 Club
 
Posts: 654
Joined: Fri Feb 16, 2007 11:28 am
Location: Tx., Milam
Zip Code: 75959

Re: Bad Boy ZTR

Postby Rodney51Cub » Fri May 18, 2012 7:27 pm

Which Bad Boy are you looking at ? How much do you have to mow, how many hills, and is it residential or do you do commercial mowing ? I ask this because sometimes people buy to small a mower for what they mow or get to big of one they can't manuver every where. The Bad Bay MZ is a good mower for small yards. They are 42" and 48" cut. You can get a Briggs or a Kawasaki motor. They have sealed hydraulic drives. They ride kind of rough because of the smaller tires. The ZT is the next step up. They are 50" and 60" cuts. Has either a Briggs, Kohler, or Kawasaki engine. Hydraulic drives are serviceable with filters. A better ride than the MZ and can do what they call a seat up grade to a supension style seat which helps the ride alot. The CZT is a basically a ZT with bigger rear tires and bigger hydraulic drives. The Outlaw and variations come with a 54", 61" and 72" cuts. Motors and horsepowers vary with model. I do not care for the stock seat on the Outlaw, the arm rests are not that well made. Other than that, it is a good mower and runs faster than I need to go. The diesel models are about the same as the Outlaw XP just with a diesel motor. You can get different seats and tires with each mower, depending on what you are mowing. If mowing residential, my choice would be a ZT with a Kolher engine 60" cut and supension seat. I work at a Bad Boy / Snapper / Simplicity dealership as a mechanic. Do not own a Bad Boy yet but will buy a ZT when I wear out the mowers I have.

Rodney 8)
Last edited by Rodney51Cub on Sat May 19, 2012 6:59 am, edited 1 time in total.
Farmall Cub Ol Red # 137572 August 1951
Sometimes, I amaze myself !
If you can not learn to do it well, learn to enjoy doing it badly.
Rodney51Cub
Cub Star!
Cub Star!
 
Posts: 231
Joined: Fri Feb 11, 2011 6:06 pm
Location: Southern Illinois
Zip Code: 62995
Tractors Owned: 1951 Farmall Cub
C-22 sickle mower
Bush Hog 412 mower
193 plow
144 cultivators
1950 John Deere A
Circle of Safety Award
Circle of Safety: Y

Re: Bad Boy ZTR

Postby Mr E » Fri May 18, 2012 9:13 pm

Don't have a BadBoy, but do have a Scag ZTR. Grass cutting machine, but a rough ride.
In the middle of every difficulty lies opportunity. - Albert Einstein


Roy Edenfield
Deep South CubFest
February 13 & 14, 2015
User avatar
Mr E
501 Club
501 Club
 
Posts: 5330
Joined: Mon Jul 30, 2007 11:48 am
Location: FL, Sneads
Zip Code: 32460
eBay ID: noles1432460
Circle of Safety Award
Circle of Safety: Y

Re: Bad Boy ZTR

Postby redfin » Fri May 18, 2012 9:27 pm

The folks in this area that I have talked to love them. Reasonably priced compared to others. Appear to be better built than the home center models. Just an added note. The owner of a nearby tractor sales and service buisiness sells many brands of ZTR mowers such as Scagg , Exmark , Hustler , Grasshopper and another one I cant recall. He cuts his acreage with a Grasshopper.
redfin
Cub Pro
Cub Pro
 
Posts: 4021
Joined: Mon Dec 17, 2007 6:25 pm
Location: LA, Gonzales
Zip Code: 70737
Circle of Safety Award
Circle of Safety: Y

Re: Bad Boy ZTR

Postby Jackman » Sun May 20, 2012 3:21 am

No Bad Boyz's but I do have three Exmark ZTR's, Exmark makes a darn good mower!
57 Lo-Boy
87 John Deere 850 4X4
Jackman
501 Club
501 Club
 
Posts: 1705
Joined: Mon May 15, 2006 4:26 am
Location: Kingston, New York
Zip Code: 12487
Circle of Safety Award
Circle of Safety: Y

Re: Bad Boy ZTR

Postby Billy Fussell » Sun May 20, 2012 8:11 am

Thanks for the feedback. I cut about 6 acres, mostly pretty flat and no trees. I do have a few steep slopes. I was looking at a 60" CZ mower at Tractor Supply, and liked the looks of it. I prefer the Kawasaki engine over the Kholer. I will Google the CZT and look at the specs. I like the idea of servicable hydrolic drives.
Billy Fussell
501 Club
501 Club
 
Posts: 654
Joined: Fri Feb 16, 2007 11:28 am
Location: Tx., Milam
Zip Code: 75959

Re: Bad Boy ZTR

Postby Jackman » Sun May 20, 2012 8:20 am

Kawasaki engines suck :!: been there done that :evil: ,,,,,,, problem limited parts supply compared to Kohler and reoccurring issues head gaskets, water leaks and exhausts that rust through too quickly....


Kohler tried and true and every dealer around has parts when ya need them. I am on my third and last Kawasaki going back to Kohler.


Z mowers are tricky on slopes but with experience you'll get the hang of it and climb and cross most inclines, Z's are also slick on wet grass but like the slopes you get the hang of it...
57 Lo-Boy
87 John Deere 850 4X4
Jackman
501 Club
501 Club
 
Posts: 1705
Joined: Mon May 15, 2006 4:26 am
Location: Kingston, New York
Zip Code: 12487
Circle of Safety Award
Circle of Safety: Y

Re: Bad Boy ZTR

Postby Jackman » Sun May 20, 2012 8:25 am

Six acres on a Z mower probably about 2 hours cut time + or - 15 minutes...
57 Lo-Boy
87 John Deere 850 4X4
Jackman
501 Club
501 Club
 
Posts: 1705
Joined: Mon May 15, 2006 4:26 am
Location: Kingston, New York
Zip Code: 12487
Circle of Safety Award
Circle of Safety: Y

Re: Bad Boy ZTR

Postby Billy Fussell » Sun May 20, 2012 12:56 pm

Thanks for the additional info. All opinions are welcome.
Billy Fussell
501 Club
501 Club
 
Posts: 654
Joined: Fri Feb 16, 2007 11:28 am
Location: Tx., Milam
Zip Code: 75959

Re: Bad Boy ZTR

Postby John *.?-!.* cub owner » Sun May 20, 2012 2:54 pm

If you have a Simplicity or Ferris dealer in your area you may want to look into them. The commercial ones are very well built. Like most ZTRs though they are not designed to let the grass get 7 or 8 inches high then take it down to 2 inches. They are designed to only take a couple inches off. All ZTRs are intended to kep a yard looking like a golf course, not take it form a grown up field to a golf course. One thing I like about the Simplicity and Ferris is that the commercial modles have independent suspension, makes it a lot easier on an old back. They are not cheap though.
"The Constitution is not an instrument for the government
to restrain the people, it is an instrument for the people to restrain the
government lest it come to dominate our lives and interests." Patrick Henry
User avatar
John *.?-!.* cub owner
Team Cub Guide
Team Cub Guide
 
Posts: 19093
Joined: Sun Feb 02, 2003 2:09 pm
Location: Mo, Potosi
Zip Code: 63664
Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.

Re: Bad Boy ZTR

Postby VinceD » Sun May 20, 2012 8:27 pm

Billy, we also mow about 6 acres. We use a Dixie Chopper and love it. Started with a smaller one for "trimming" and traded up to a 60". I cut with a 72" finish mower and Annie runs the Dixie Chopper. She cuts circles around me. I consider it extremly well built and would highly recommend the brand. :D :D
Vince
High atop Hummingbird Hill
In the Missouri Ozarks
Image
VinceD
501 Club
501 Club
 
Posts: 4524
Joined: Mon Apr 17, 2006 9:17 pm
Location: MO, Bakersfield, (South - Central)
Zip Code: 65626
Tractors Owned: 1949 Cub "Frodo"
1949 Cub "Sam" (future Project)
1965 Lo-Boy "Pippin"
1940 H "Walter"
1953 SC "Gimli"
Cub Cadet HDS 2155
Circle of Safety Award
Circle of Safety: Y

Re: Bad Boy ZTR

Postby JackF » Wed May 23, 2012 5:34 am

John Stated:

Like most ZTRs though they are not designed to let the grass get 7 or 8 inches high then take it down to 2 inches. They are designed to only take a couple inches off.


That’s correct. I have a commercial grass cutter and it seemed every time I got time to cut the grass it always was to tall for the mower to cut correctly. When the grass wasn’t cut when it should had been I always had skipped spots, lumps of grass that had to be raked up and an expensive belt that was slipping unnoticed driving the mower blades.

The fuel cost for cutting grass what I had to cut was getting ridiculous so I moved that part of my property to hay fields. Now it gets cut two times a year.

My commercial grass cutter is being rented to a commercial grass cutter and I’m using something that cuts the grass over 6” tall.
I’m really good at doing nothing…With that said…I’m really, really good at doing nothing
JackF
501 Club
501 Club
 
Posts: 904
Joined: Sat Feb 15, 2003 7:20 am
Zip Code: 00000


Return to Off Topic

Who is online

Users browsing this forum: No registered users and 2 guests