Tue May 29, 2012 9:50 am
I have a early model Farmall Cub that has a different size oil filter in it. The 1153 filter is much shorter than the one in it. This is a manual lift tractor and there isn't a serial number tag on it. The filter that came out of it has tractor supply and kleenite on the top and L-101 on the side. I can't find a cross referance on it anywhere. Thank RT
Tue May 29, 2012 11:24 am
All of the cub engines take the same filter, standard, lo boy, i54, 185, or 184, manual or hydraulic lift. I have 12 cubs, and 2 power units. I have no idea what that filter could be from. It can't be much longer than the 1153 filter, or it wouldn't fit in the housing. Ed
Tue May 29, 2012 4:03 pm
Just because it came out doesn't make it the correct one. No telling what somebody stuffed in there.
It's not a really old sock style like the ones in the early parts manuals? http://www.cleancomputes.com/Cub/Cub%20Parts%20Manuals/TC-37A%20(5-2-49)/Engine/Page-20.jpg
Has the filter housing, cast as part of the block, been modified? If not will the 1153 filter fit? How is the overall length of the 1153 compared to the overall length of the one you removed? Is the one you took out built the same, I'm thinking maybe without the nipples on each end therefore appearing longer.
Pictures of the filters and housing may help identify the problem. Welcome to the forum
, we'll get the mystery solved. Feel free to ask plenty of questions.
Oh and if the tractor hasn't been started for awhile make sure to prime the oil pump
Tue May 29, 2012 4:08 pm
Are we absolutely sure that we're dealing with a Farmall Cub here? Can you post a photo of your tractor?
Tue May 29, 2012 8:54 pm
I will try to post pictures tomorrow. The casting number located behind the oil filter housing is 354898 R1. The distributor is pointing up instead sideways and the oil pressure gauge screws in the casting. RT
Tue May 29, 2012 9:04 pm
International / Farmall Engine Parts Catalog Fuel / Engine Model. Engine serial #. Page. International Applications. A. C113/
C123. C113. Tractor. IH113-1. G. A. C113/C123. C113; Block# 354898R1-R4 ...
Tue May 29, 2012 9:07 pm
That part # is shown in my TC-53 Farmall 200 parts book as a crankcase(cylinder block). Your tractor is not a Cub. The vertical distributor was likely swapped from another tractor.
Tue May 29, 2012 9:10 pm
robbietarleton wrote:I will try to post pictures tomorrow. The casting number located behind the oil filter housing is 354898 R1. The distributor is pointing up instead sideways and the oil pressure gauge screws in the casting. RT
Sounds like a Delco distributor, but that part number I believe is for a Super A???? Pictures please....
Tue May 29, 2012 9:34 pm
I got some pictures if I can figure how to post them. Thanks guys for the help. We will figure it out.RT
Tue May 29, 2012 10:21 pm
Don't need a picture. 354898 R1 is a late Super A or a Super C. Serial plate should be on the left seat support, unless the seat has been changed.
Wed May 30, 2012 5:34 am
Email the photos to me at email@example.com
and I'll post them for you.
Wed May 30, 2012 7:50 am
I got the serial number off the seat post. #FAA35341. I think it is a 1940 A model. Thanks for the help. RT
Wed May 30, 2012 2:36 pm
RT, there are several guys on the board who have experience with the "A" as well. Any of which would be glad to assist with your questions. There's also a special category for other IH equipment.
Wed May 30, 2012 3:07 pm
robbietarleton wrote:I got the serial number off the seat post. #FAA35341. I think it is a 1940 A model.
Yes, 35341 would be 1940. However, that block part number is inconsistent with 1940. If you missed a digit in the serial number and it is really FAA35341?, it would be a '54 Super A. Either you have a Super A or the engine has been replaced with a newer one. Do you have a hydraulic system?
Wed May 30, 2012 7:36 pm
A little late, but here are two of Robbie's photos...
Definitely an A.
Powered by phpBB © phpBB Group.
phpBB Mobile / SEO by Artodia.