This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Cheap And Dirty Lawn Rake
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 6338
- Joined: Wed Sep 12, 2007 8:40 pm
- Zip Code: 49120
- Circle of Safety: Y
- Location: Niles / Buchanan, Michigan
Cheap And Dirty Lawn Rake
Once again, laziness seems to be the motivating force propelling me to fabricate something to make my life easier. This time it’s the daunting chore of raking leaves. The older I get, the more mechanized I try to become to alleviate physical work that seems to because harder and harder. I've avoid raking with a passion and normally use a leaf blower but that takes up quite a bit of time especially when I am trying to move a large pile. I typically blow the leaves into the field once the corn or beans have been picked.
Today I gave my Cheap And Dirty Lawn Rake a try. I am pleased with the results. Now I have another reason to operate my Cub. It isn’t prefect but it does work really well. Sure beats pulling on a rake handle or hoisting the leaf blower. It’s much quicker too.
I fabricated it using 2”x 2” x 10 ga. box tubing (4‘6“ long) , 3”x4”x .25” angle iron 62” long and some .25” x 6” x18” plate steel for the pivot brackets. I again used the same anchor, which attaches into the 2” receiver, that I use with all my Cheap And Dirty implements.
The 6” wide pivot plates straddle the anchor to stabilize the rake and absorb tensional load similar to the other implements. However, the plates on the rake are slightly larger due to the additional torsion and side loading caused by the wide rake.
The beam has an offset in it to allow clearance for the draw bar and the angle iron is attached perpendicular to the ground. Mounted on the angle iron are 22 rake teeth that I purchased at a tractor swap meet. I got a box of 36 of them or $20!
When I mounted the teeth, the angle was wrong for the application I wanted.
A quick bend with a ¼” tubing bender setting them more perpendicular to the ground allowed them to work as I intended.
The rake is not completely painted in the photos because I intend to add a gusset between the angle iron and the beam for additional strength. I may also add an extension to the angle iron to keep leaves from going over the top of the rake as they pile up in front of the rake.
It only took a few minutes to clean this portion of the back yard. Again, not perfect but by tomorrow, the way the leaves are starting to fall, you'll never know it was ever raked.
Today I gave my Cheap And Dirty Lawn Rake a try. I am pleased with the results. Now I have another reason to operate my Cub. It isn’t prefect but it does work really well. Sure beats pulling on a rake handle or hoisting the leaf blower. It’s much quicker too.
I fabricated it using 2”x 2” x 10 ga. box tubing (4‘6“ long) , 3”x4”x .25” angle iron 62” long and some .25” x 6” x18” plate steel for the pivot brackets. I again used the same anchor, which attaches into the 2” receiver, that I use with all my Cheap And Dirty implements.
The 6” wide pivot plates straddle the anchor to stabilize the rake and absorb tensional load similar to the other implements. However, the plates on the rake are slightly larger due to the additional torsion and side loading caused by the wide rake.
The beam has an offset in it to allow clearance for the draw bar and the angle iron is attached perpendicular to the ground. Mounted on the angle iron are 22 rake teeth that I purchased at a tractor swap meet. I got a box of 36 of them or $20!
When I mounted the teeth, the angle was wrong for the application I wanted.
A quick bend with a ¼” tubing bender setting them more perpendicular to the ground allowed them to work as I intended.
The rake is not completely painted in the photos because I intend to add a gusset between the angle iron and the beam for additional strength. I may also add an extension to the angle iron to keep leaves from going over the top of the rake as they pile up in front of the rake.
It only took a few minutes to clean this portion of the back yard. Again, not perfect but by tomorrow, the way the leaves are starting to fall, you'll never know it was ever raked.
1929 Farmall Regular
1935 John Deere B
1937 John Deere A
1941 John Deere H
1952 John Deere B
1953 Farmall Cub
1935 John Deere B
1937 John Deere A
1941 John Deere H
1952 John Deere B
1953 Farmall Cub
-
- 10+ Years
- Posts: 438
- Joined: Tue Aug 07, 2012 1:37 am
- Zip Code: 44134
- Tractors Owned: 1949 & 1951 Farmall Cubs
Several Snapper Garden Tractors - Circle of Safety: Y
- Location: Southern Suburbs of Cleveland, Ohio
Re: Cheap And Dirty Lawn Rake
Lazy is my first name so I know where you're comin' from.
Cool.
Cool.
"HAVE ALL YOUR DELIVERIES MADE BY UNION DRIVERS"
-
- 10+ Years
- Posts: 2253
- Joined: Fri Sep 10, 2010 5:23 pm
- Zip Code: 39861
- Tractors Owned: 76 Cub Denim Springs
49 Cub Denim Springs
51 Cub Uncle Harvey
"Jacksonville" 53 Cub
"Jackson" 76 Cub
"Louie" 64 Cub Fast Hitch
"Paw Paw"71 Cub Fast
Hitch
"Alvin" 72 Cub
"Ugly" 75 Cub
76 Cub Val
Mr. Kirkland" 77 Red Cub
77 Cub "Russell
76 Cub w/fast hitch "Edgar"
76 - 185 Cub Lo Boy
John Deere 2003 - 5320
Kubota 7060
Kubota 5400
Kubota 2680
John Deere 445
TO20 Ferguson - Circle of Safety: Y
- Location: Jakin Georgia
-
- Team Cub
- Posts: 24272
- Joined: Tue Aug 07, 2007 3:39 pm
- Zip Code: 45030
- Tractors Owned: At This Time
40 Farmall Cubs (Round Hood)
2 Farmall Cub (Square Hood)
2 IH Cubs (Square Hood)
5 Lo-Boys (Round Hood)
2 Lo-Boys (Square Hood)
2 Farmall 404's
1 Farmall H
1 Ferguson 20
1 Cub Cadet 125
1 Kubota B-7100 - Circle of Safety: Y
- Location: OH, New Haven (Hamilton County)
Re: Cheap And Dirty Lawn Rake
ricky racer wrote:Sure beats pulling on a rake handle or hoisting the leaf blower. It’s much quicker too.
Now you can pull on the shifter and hoist a beverage!
ricky racer wrote: I intend to add a gusset between the angle iron and the beam for additional strength.
At least you aren't hoisting any engines with it!
Looks like you hit on a winner there. I like it.
There are two ways to get enough Cubs. One is to continue to accumulate more and more. The other is to desire less.
-
- 10+ Years
- Posts: 669
- Joined: Wed Sep 30, 2009 9:43 am
- Zip Code: 77355
- eBay ID: czechiii
- Tractors Owned: 48 Cub SN 54XXX (Captain Crunch)
47 Farmall A (Patches) - Circle of Safety: Y
- Location: Magnolia, Texas
Re: Cheap And Dirty Lawn Rake
Very cool cheap an dirty tool!!!!
Charles Patek III
Some days - Chicken.......Some days - Feathers
Words to live by....
Some days - Chicken.......Some days - Feathers
Words to live by....
-
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger - Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
Re: Cheap And Dirty Lawn Rake
Rick:
Now that is some engineering to fill a need Rick we really need a dimensioned sketch for your Cheap and Dirty basic boom structure. This really is quite the kit for adding specific implements for specific jobs without breaking the CubFundBank Quite the fabrication job tres
Now that is some engineering to fill a need Rick we really need a dimensioned sketch for your Cheap and Dirty basic boom structure. This really is quite the kit for adding specific implements for specific jobs without breaking the CubFundBank Quite the fabrication job tres
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship
-
- 10+ Years
- Posts: 923
- Joined: Thu May 06, 2010 1:36 pm
- Zip Code: 47201
- Tractors Owned: 105 & 127 cadet (sacrificed for a 4wd project)
680 Cadet
1964 LoBoy FH
L-54A Blade
Pennington 3 spindle deck
LF-194 plow - Circle of Safety: Y
- Location: IN, Columbus
Re: Cheap And Dirty Lawn Rake
I like it....
-
- 10+ Years
- Posts: 3560
- Joined: Thu Apr 22, 2010 2:31 pm
- Zip Code: 17953
- Tractors Owned: ......Almost enough.
N3NIK - Circle of Safety: Y
- Location: PA, Middleport (Schuylkill County)
Re: Cheap And Dirty Lawn Rake
Great rake Ricky !!
Superb design and fab.
I have also been watching for a 'cheap' rake for some small projects.
Superb design and fab.
I have also been watching for a 'cheap' rake for some small projects.
Dave
"More gold has been mined from the thoughts of men than has been taken from the earth." -- Napoleon Hill
"More gold has been mined from the thoughts of men than has been taken from the earth." -- Napoleon Hill
-
- 10+ Years
- Posts: 2680
- Joined: Mon Oct 24, 2005 11:35 am
- Zip Code: 14072
- eBay ID: toysforjake
- Tractors Owned: Lots of Cub Cadets!
1951 Farmall Cub
1977 IH Cub
1966 IH Cub
1965 IH Lo Boy
1964 IH Lo Boy
1949 Farmall Cub
Several IH 154 Lo Boys
1979 IH 184 Lo Boy
Simplicity 4416 Sovereign
Simplicity Conquest
Simplicity Legacy 4x4 Diesel
Mitsubishi MT180D 4x4 Diesel - Circle of Safety: Y
- Location: Grand Island, NY
Re: Cheap And Dirty Lawn Rake
Rick,
Awesome!! I've been thinking about doing that exact same thing. I already have some 2"x2" angle welded up in a rectangle about 70" wide and about a foot apart (was a highway tail gate for my old trailer).
What tines did you use, and can you post a picture of how they're fastened?
Thanks,
Bill
Awesome!! I've been thinking about doing that exact same thing. I already have some 2"x2" angle welded up in a rectangle about 70" wide and about a foot apart (was a highway tail gate for my old trailer).
What tines did you use, and can you post a picture of how they're fastened?
Thanks,
Bill
Cub Cadets 682, 1811, 1864, Simplicity Legacy XL 4x4 Diesel with FEL, 60" mower, 50" Tiller
-
- 10+ Years
- Posts: 523
- Joined: Fri Feb 11, 2011 6:06 pm
- Zip Code: 62995
- Tractors Owned: 1951 Farmall Cub
1950 John Deere A
1949 Farmall Cub
1943 Farmall H
1940 Farmall H
1953 Farmall Super M
1962 Massey Ferguson 65 - Circle of Safety: Y
- Location: Southern Illinois
Re: Cheap And Dirty Lawn Rake
ricky racer wrote:Once again, laziness seems to be the motivating force propelling me to fabricate something to make my life easier. This time it’s the daunting chore of raking leaves.
I do not call it laziness. I call it working smarter not harder. Nice setup.
USAF 1976 - 1996
-
- 10+ Years
- Posts: 6338
- Joined: Wed Sep 12, 2007 8:40 pm
- Zip Code: 49120
- Circle of Safety: Y
- Location: Niles / Buchanan, Michigan
Re: Cheap And Dirty Lawn Rake
gitractorman wrote:Rick,
Awesome!! I've been thinking about doing that exact same thing. I already have some 2"x2" angle welded up in a rectangle about 70" wide and about a foot apart (was a highway tail gate for my old trailer).
What tines did you use, and can you post a picture of how they're fastened?
Thanks,
Bill
I knew this would get some wheels turning!! As mentioned the rake teeth were purchased at a tractor swap meet. Many types are available at farm stores. Here are some pictures of what I used.
A single 3/8" hex bolt with flat and lock washers hold them in place.
1929 Farmall Regular
1935 John Deere B
1937 John Deere A
1941 John Deere H
1952 John Deere B
1953 Farmall Cub
1935 John Deere B
1937 John Deere A
1941 John Deere H
1952 John Deere B
1953 Farmall Cub
-
- 10+ Years
- Posts: 3736
- Joined: Sun Jul 13, 2008 10:05 pm
- Zip Code: 45067
- Tractors Owned: 1951 Cub, 2-1955 Loboy w FH, a few plows, discs, mowers, blades, carrier & such
Several '61 CC Originals, Cub Cadet 100, several 102's & 122's, 124, various CC options & implements, #1Trailer, 1963 Springfield, JD 770, Ford 8N - Circle of Safety: Y
- Location: OH, Trenton
Re: Cheap And Dirty Lawn Rake
Another sweep sweet project there Ricky!
You got my wheels turning on a smaller version for a Cadet... for my smaller yard!
Great job, thanks for sharing!
You got my wheels turning on a smaller version for a Cadet... for my smaller yard!
Great job, thanks for sharing!
David
-
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger - Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
Re: Cheap And Dirty Lawn Rake
Rick:
Now I am going to be scrounging the local swap meet/and dealerships for liquidation stock so I can make me one of them.
Now I am going to be scrounging the local swap meet/and dealerships for liquidation stock so I can make me one of them.
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship
-
- 10+ Years
- Posts: 1224
- Joined: Wed Jul 02, 2008 6:11 am
- Location: MN, Mankato
Re: Cheap And Dirty Lawn Rake
I have a similar dethatcher that I've never tried with leaves. Yours did a great job moving the leaves. I'll have to try mine for leaves. Thanks for the idea.
Todd
Todd
-
- 10+ Years
- Posts: 2680
- Joined: Mon Oct 24, 2005 11:35 am
- Zip Code: 14072
- eBay ID: toysforjake
- Tractors Owned: Lots of Cub Cadets!
1951 Farmall Cub
1977 IH Cub
1966 IH Cub
1965 IH Lo Boy
1964 IH Lo Boy
1949 Farmall Cub
Several IH 154 Lo Boys
1979 IH 184 Lo Boy
Simplicity 4416 Sovereign
Simplicity Conquest
Simplicity Legacy 4x4 Diesel
Mitsubishi MT180D 4x4 Diesel - Circle of Safety: Y
- Location: Grand Island, NY
Re: Cheap And Dirty Lawn Rake
Yea, I'm definitely going to make one up. I actually need it for dethatching, but I like the leaf rake idea. The Oak trees here dont drop leaves until it's way too late, and they're typically too wet to move with the leaf blower, and too heavy to rake by hand. This is definitely a potential answer!!! Thanks!
Cub Cadets 682, 1811, 1864, Simplicity Legacy XL 4x4 Diesel with FEL, 60" mower, 50" Tiller
-
- Similar Topics
- Replies
- Views
- Last post
-
- 32
- 1121
-
by Indy4570
Sat Nov 20, 2021 11:09 am
Who is online
Users browsing this forum: Don McCombs, Majestic-12 [Bot] and 11 guests