All non-Cub/Cadet/IH/Farmall/Case tractor and machinery discussions.
Moderator: Team Cub
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
11 posts • Page 1 of 1
I received the ride-a-matic I purchased out of MI the other day. Thanks Karl, and a big thanks to your BIL? (forgot his name (mr Woody)) for the cub express.
It is in perfect shape for what I wanted- a toy to ride on at tractor shows.
It has a Kohler K-160 7 hp. I filed the points and have great spark. Cleaned the carb, and it will fire, but have not gotten it running yet.
It has a Carter #1 carb. I made a bowl gasket, but really need a new one. Can anyone point me to where to start with the adjustments?
Last edited by Former Member on Mon Oct 15, 2012 3:25 pm, edited 1 time in total.
In a topic below, Wisconsin Engine, is a link to a garden tractor web site. On the site are down loadable manuals for Kohler engines.
If the adjustments asked for is the carburetor. Try 1 to 1/4 turns out on both needle valves to start with. Once engine starts you can fine tune. CRS. Manuals not on hand. I think the low speed idle jet is 3/4 turn out and the main jet is about 1 1/2 turn out.
Kohler parts, auto parts store. Single gaskets can be purchased including carburetor gaskets.
I have an excuse. CRS.
I have a wizard version of the round hood ride o matic, kohler k90 engine. Missing the clutch disc so it is just sitting for now.
The K160 and K161 had a bendix magneto on the flywheel, prone to cracking of the plastic coil. Your's may have been replaced over the years. If so then that is a good thing. I would check the valves and other than that not much to go wrong. If it is the carb I am thinking of, there is a welch plug that covers part of the idle circuit, make sure it has not fallen out. Does it run with starting fluid?
I just got a can last night to try (carb and choke cleaner). On the list for this morning.
Had the head off and valves looked great.
I am getting a hot blue spark, so with proper air/fuel mixture, it should start and run.
That clutch system with varying speed control is wild. I bet the clutch disc is one expensive puppy, IF you can find one.
After playing with it some more today, and adding 2+2 together, I believe it is lack of compression. With the starter engaged, I can hold my thumb over the plug hole.
Also, I noted that there is a lot of old oil grime and dirt everywhere. The fins on the jug were full of it, and when I pulled the head, it looked as though oil had been seeping under it. For a long time. I think I will stufy up on it and see about replacing the rings, as that is the only place oil on the head could come from. I will also double check the valves and timing while i have it off the tractor.
fun fun fun.
choke and carb cleaner is flammable, but does not work well as starting fluid for engines. It doe work well as starting fluid on your hair if you are smoking when using it though.
"The Constitution is not an instrument for the government
to restrain the people, it is an instrument for the people to restrain the
government lest it come to dominate our lives and interests." Patrick Henry
I try to stay away from starting fluid. It can be a bit harsh on small engines I have had to replace a couple.
Very nice Bolens. I kinda like em. My buddy Marc collects them although I don't think he has that particular model. My buddy in Dale McKay has that one though. I know I have the Parts Lists in my files but not sure about the Owner's Manual. I think I have the service manual as well.
It is on the back burner for right now. Dealing with the end of Cub season and winter prep. I have the motor off and in my truck, the rest of the tractor is all there and filthy greasy.
I plan to tear it down to clean it, and to shim, replace bushings and basically tighten it up. I will replace the rear ags with cub front wheels, or perhaps i can find some soft atv balloon tires for the rear. I am planning to just clean it, fix the engine and take it to shows to ride on, rather than a golf cart (except where prohibited.)
Not going to put any paint on it for now. I would like to find a new hood for it. it looks good, but the vibrations have broken the front bolt holes out, and it is being held on with washers,.
A washer could likely be welded in to repair those hood holes.
'52 Cub ("Great Personality") 148xxx
'48 Cub with FH ("Gunny Cub") 38xxx
'57 Lambretta (a slow work in progress)
'74 Triumph TR6 (Mama's toy)
11 posts • Page 1 of 1
Who is online
Users browsing this forum: No registered users and 3 guests