Put on a thin layer of Permatex RTV. lick your finger and smooth it out and wipe off the excess. Set it aside and let it dry(overnight) so it is completely dry. Then install, if you think it was needed.
Allowing it to dry will prevent the 2 parts from sticking together.
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
oil bath cup?
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 398
- Joined: Tue Nov 30, 2010 7:54 pm
- Zip Code: 23027
- Circle of Safety: Y
Re: oil bath cup?
As Dale said the RTV will work wonders on it if you think it is necessary. I have used that stuff to fix many things including cracks in a lawnmower seat, used it in holes where wires pass thru metal and such. It's uses are endless if your creative!
-
- 10+ Years
- Posts: 71
- Joined: Sat May 15, 2010 12:49 pm
- Zip Code: 63069
- Tractors Owned: "57" highcrop cub
"55" no hole
"61" cub
435 veg planter
201 corn planter
474 veg planter
447 cultivator
252 cultivator - Location: Pacific, MO
Re: oil bath cup?
Guys, If I remember right , I used an old oil filter gasket of a A farmall and stretched it around the were the gasket was, Fit like a glove,Mike
-
- 10+ Years
- Posts: 489
- Joined: Thu May 19, 2005 2:04 pm
- Zip Code: 35216
- Tractors Owned: 1947 Cub
1949 Cub
2011 JD X320 - Circle of Safety: Y
- Location: Birmingham Al/Bay Springs Ms.
Re: oil bath cup?
While we are on the subject, I just got to the point in my refurbish to install oil in my air cleaner cup this afternoon. I oiled it up in both the inner portion as well as the outer cup. Was this correct, or should I not have added oil to the inner cup? By the way, my filter assembly had the fiber style thin gasket which has been shown in this posting.
Since retirement, the things I miss most are the holidays!
-
- 10+ Years
- Posts: 2929
- Joined: Sun Apr 19, 2009 9:51 pm
- Zip Code: 63664
- Location: MO, Potosi
Re: oil bath cup?
I haven't looked for a gasket on my Cubs but am wondering what the purpose or need is for one in that location. It is on the "dirty air" side of the filter at that point. Air comes down the center of the filter does a sharp 180 back up through the mesh and then is drawn off and back down the outside pipe to the carb, right? What little dirt that could enter around the cup would be heading "south" at that point so it would have to do a 180 as well before joining the airflow.
Thiggy; fill it to the line embossed in the outside cup. That will be above the holes in the inner cup so both should/will be filled.
Thiggy; fill it to the line embossed in the outside cup. That will be above the holes in the inner cup so both should/will be filled.
-
- 10+ Years
- Posts: 438
- Joined: Tue Aug 07, 2012 1:37 am
- Zip Code: 44134
- Tractors Owned: 1949 & 1951 Farmall Cubs
Several Snapper Garden Tractors - Circle of Safety: Y
- Location: Southern Suburbs of Cleveland, Ohio
Re: oil bath cup?
Scrivet wrote:I am wondering what the purpose or need is for one in that location. It is on the "dirty air" side of the filter at that point.
One could only believe the engineers determined the air quality directly in the air flow path created by the cooling fan was poor, so air with less particulate matter is drawn from above the hood.
The air cleaner gasket surface forms a better seal than metal to metal contact could achieve preventing fan driven dirt from entering the system, which would require a higher maintenance frequency of the oil cup, which is only 10 hours or less as it is.
If a "loose" gasket was used, you can rest assured it would eventually drop out and possibly never replaced.
If the gasket surface was permanently applied at Donaldson, technically no gasket exists except on the manufacturing blueprints, leading to a debate as to why no gasket illustration or mention exists in the IHC service or parts manuals.
"HAVE ALL YOUR DELIVERIES MADE BY UNION DRIVERS"
-
- Cub Star!!
- Posts: 270
- Joined: Sat Oct 02, 2021 12:04 pm
- Zip Code: 28635
Re: oil bath cup?
As I understand it changes and improvements were implemented by I H engineers at certain serial numbers during the cub production run, and new parts would be listed in I H parts books. This could be a vendor ( Donaldson ) R&D improvement that went on for some time.
Who is online
Users browsing this forum: staninlowerAL and 18 guests