I need a little help with my new cub.

[Josh Blair]

Ok so my new cub has decided to be a little finicky with me about starting, and I'm having some trouble getting her started.
It is on the 6 volt system still and has a rebuilt generator. I currently suspect the carb to be part of the problem as every time I turn the gas on, it goes straight onto the ground. I took the carb off and think the float stop could need to be bent down as I dont think its where it's supposed to be. I have not checked spark yet because the carb seemed to be an obvious problem.

[Chris D]

Yeah first things first is to address the carb. Looks like it needs to be pulled down and given a good cleaning. Sounds like trash in the needle and seat assemble. I would clean all that, clean the fuel strainer on the fuel bowl unit and drain all old gas. Maybe while your in the carb just rebuild it. Doesn't cost that much.

[Josh Blair]

Yeah first things first is to address the carb. Looks like it needs to be pulled down and given a good cleaning. Sounds like trash in the needle and seat assemble. I would clean all that, clean the fuel strainer on the fuel bowl unit and drain all old gas. Maybe while your in the carb just rebuild it. Doesn't cost that much.

Well one good thing about this cub is the gas tank had no old gas in it and what is in there now is fresh 93. The PO had cleaned the tank so it is spotless.

[JackF]

Do what Chris wrote and hopefully this will help:

http://www.farmallcub.com/phpBB2/viewtopic.php?f=1&t=53055
http://www.youtube.com/watch?v=tY9YGHlDfjk
http://www.youtube.com/watch?feature=player_detailpage&v=iEFkMScOqiM
http://www.farmallcub.com/phpBB2/viewtopic.php?f=1&t=7110
http://www.cleancomputes.com/Cub/Blue%20Ribbon%20Service%20Manuals/GSS-1411%20Service%20Manual%20for%20Cubs%20and%20Lo-boy%20Tractors/index.html (Section 2 - Fuel System)
For some reason I was knocked off when I was posting a reply… Also…I would make sure the carburetor float does not have a hole in it

[Barnyard]

The problem I see with that you tube video is that the guy has a TSC kit and the guy points out some of the problems with that kit (long threads on seat, wrong instructions,etc.) and still uses it in his video. The only good video would be one using all parts that will make the job easier for the novice.

There was a carb repair video made almost a year ago at DSCF showing the right stuff and I have not been able to find it on the forum. Has it ever been posted?

[Dale Shaw]

Put the carb off Lorreta on it. It was a good carb when it left here last summer.

[Josh Blair]

Put the carb off Lorreta on it. It was a good carb when it left here last summer.

Well I am gonna, just when my mom isn't looking because apparently she doesn't like that I'm doing that

[Dale Shaw]

Josh, if your Mom say's NO, Don't. You CAN figure it out.

Hope i do not need to call her.

Dale

[beaconlight]

Josh ask mom to help you swap to see if you can get the new one running and then move it back. She might offer to help. Moms are like that. Some of the greatest people in the world. Of course I wouldn't ask till after christmas or she may do the carb swap and have you cook the turkey.

[JackF]

Barnyard wrote:

The problem I see with that you tube video is that the guy has a TSC kit and the guy points out some of the problems with that kit (long threads on seat, wrong instructions,etc.) and still uses it in his video. The only good video would be one using all parts that will make the job easier for the novice.

That’s correct and I should have pointed that out before I posted that video. I also assumed part three would have automatically loaded after part two concluded another error on my part.
This was the only video illustration I could find that named Farmall.com for reference of specs and illustration of float adjustment at the time.
Please feel free if you find an improved video delete and insert….
Part three:
http://www.youtube.com/watch?feature=player_detailpage&v=iEFkMScOqiM

[Josh Blair]

well i believe the cause of the problem is a STICKY float/needle valve. I tried to take the pin out of the float and it won't budge.

[Eugene]

I tried to take the pin out of the float and it won't budge.

Gently tap on end of the pin sticking out from the pivot point. Once moved the pin can be removed with needle nosed pliers.

The pin not moving in it's anchor points is not a concern. The float should easily pivot on the pin.

[Josh Blair]

I tried to take the pin out of the float and it won't budge.

Gently tap on end of the pin sticking out from the pivot point. Once moved the pin can be removed with needle nosed pliers.

The pin not moving in it's anchor points is not a concern. The float should easily pivot on the pin.

No Im talking about the actual valve that the float controls is sticky. sorry for the misunderstanding.

[Rudi]

Josh:

I take it you mean assembly #9 which is the needle and cage?

[Josh Blair]

Josh:

I take it you mean assembly #9 which is the needle and cage?

Yes I do.