Wed Jan 02, 2013 1:21 pm
Ok, I pulled out the little glass bowl underneath the gas tank and cleaned it was well as the filter screen. When I turnover the tractor, it still does not start but when I let go of the starting lever, gas spurts out in an area where the carb looks to split in two. There are two bolts holding it in place and what looks like the gasket spilling out. I take it the gasket is shot and I need to replace it? If this is the case, I hope that that is an easy fix. I cannot find any kind of shop manual for the cub so is there any trick or things I should look for or do? Thanks.
Wed Jan 02, 2013 1:30 pm
If gas is spurting out between the gasket then air is getting in. That is definitely the thing to fix first and then go from there. Manuals can be found by clicking on the manual link at the top of this page.
Wed Jan 02, 2013 2:00 pm
There should be two studs with nuts that attach the carb to the manifold. The studs are sometimes replaced with bolts. The carb halves are held together with 4 bolts. If gas is leaking there, your gasket is probably shot, and the top may also need to be flattened so the halves fit together tightly without the gasket. I would recommend getting an OEM gasket from a Case/IH dealer or TM Tractor (sponsor at the bottom of the page). Most of the aftermarket gaskets are either paper or a thin, poor quality cork. When you separate the two halves of the carb, pull them apart parallel to each other or you risk breaking the thin idle tube. Here's the link to the carb page that Barnyard mentioned: http://www.cleancomputes.com/Cub/Blue%2 ... System.htm
Hope that helps,
Wed Jan 02, 2013 2:41 pm
Sent you a PM.
Wed Jan 02, 2013 2:46 pm
Man, do I ever smell a minifest brewing!
Wed Jan 02, 2013 2:51 pm
Barnyard wrote:Man, do I ever smell a minifest brewing!
Right between where I live and the home place, where my son lives AND right near a CASE-IH dealership, where I often get parts. Make the trip often.
Oh, forgot to mention that Ike is a Texas AGGIE also!!!!!! WHOOP! WHOOP!
Wed Jan 02, 2013 2:56 pm
I just put a bowl gasket on my '63 last year. They are about $5 at the dealer if you have one close.
You can change it without taking the carb off the tractor if you have a right angle screwdriver....http://www.sears.com/craftsman-4-pc-off ... ockType=G2
Wed Jan 02, 2013 5:18 pm
I had the same problem. It is not so easy getting cub parts in Ireland, and the cost of getting a gasket from USA is prohibitive so I took the carb off the manifold and made replacement gasket out of gasket paper. A tricky job and accuracy is very important, but necessity is the mother of invention & poverty is the father LOL. Worked a treat, but if you live in USA it would be better and handier to get the proper one.
Wed Jan 02, 2013 8:06 pm
Donegal Cub wrote:I had the same problem. It is not so easy getting cub parts in Ireland, and the cost of getting a gasket from USA is prohibitive so I took the carb off the manifold and made replacement gasket out of gasket paper. A tricky job and accuracy is very important, but necessity is the mother of invention & poverty is the father LOL. Worked a treat, but if you live in USA it would be better and handier to get the proper one.
One of our forum members made a template that is used to make your own gaskets. Another member posted this How-To http://www.farmallcub.com/phpBB2/viewtopic.php?f=139&t=64926
to describe using the template to make gaskets. Unfortunately, I do not believe the template maker has any more, however, you may be able to get one made for future use.
Thu Jan 03, 2013 8:16 pm
I definitely will be giving Bill a call. Just have to wait for warmer weather. No heat in the barn. Plenty of human anti-freeze but better if we have our wits about us.
Powered by phpBB © phpBB Group.
phpBB Mobile / SEO by Artodia.