Carb Woes

Farmall Cub Forum -- Questions and answers to all of your Cub related issues.

Moderator: Team Cub

Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
User avatar
10+ Years
10+ Years
Posts: 7147
Joined: Sat Feb 18, 2006 8:12 pm
Zip Code: 15101
eBay ID: lacrosseorgans
Skype Name: Mike.Hengelsberg
Tractors Owned: 1949 Cub "Merlin"
1955 Cub "Lewis"
Cub Trailer
A-60 Blade
Cub-22 Mower
193 Plow
Circle of Safety: Y
Location: PA, Allison Park (Am Hengelsberg)

Carb Woes

Postby Hengy » Wed Jan 09, 2013 4:01 pm

Hi all...

I have been talking with a local member via PM about their cub. One issue that came up was that a recently rebuild carb LEAKS after less than 10 minutes after opening up the fuel bowl. The person used the "deluxe" rebuild kit (not Tisco, I believe). Replaced needle valve, seat, soaked in carb cleaner, cleaned out all passages, etc, but still, after buttoning it back up, it leaks. He even put his old seat and needle valve back in the tractor and STILL has leaks. The replacement needle valve has the dreaded Viton tip, but it is NOT sticking yet. He has kept the valve and the seat as a set. Float is NOT leaking and has no fluid in it. He is confirming float height, but said he believed it was correct.

I talked with him about potentially using some valve lapping compound and lapping the original needle valve and seat together to try to get a good seal.

The reason for this thread is just to vent. I have had similar problems on a rebuilt carb on Merlin (done by one of the carb gurus" when I got the tractor originally). My leak is not rapid, but it still leaks. My problem is compounded by the fact that the valve on my fuel bowl is apparently bad as well, so I can't stop my little drip! The vent is that you would think that such a simple little carb would be easily repaired and would not be so prone to problems as this one is!
Mike (Happy as a Lark in Allison Park, PA)
Image Image

Check out my Restoration Thread (1955 Cub, Lewis)

Team Cub Mentor
Team Cub Mentor
Posts: 16803
Joined: Fri Jul 02, 2004 9:52 pm
Zip Code: 65051
Circle of Safety: Y
Location: Mo. Linn

Re: Carb Woes

Postby Eugene » Wed Jan 09, 2013 4:11 pm

Hose barb to fit carb inlet, clear plastic tubing to match the hose barb, funnel small enough to fit inside the clear plastic tubing and a bottle of rubbing alcohol from the dollar store.

Remove carburetor top, turn and block upside down on bench with hose barb, tubing and funnel attached. Funnel above carburetor, fill with alcohol. Observe needle valve area and remainder of carb top for source of leakage.
I have an excuse. CRS.

Clark Thompson
10+ Years
10+ Years
Posts: 1562
Joined: Sun Feb 02, 2003 11:01 pm
Zip Code: 44425
Tractors Owned: I own a 1950 cub demo, 1948 farmall cub, 1944 International I-9, a 1976 internationl cub, a 1975 international cub with fast hitch roleover plow and disc. a 1962 JD-440 dozer with 253 detroit, a 1952 JD-B, a 1979 international 3200 skid loader, a 1957 international S-160 truck, a 1929 Mccormic deering 10-20, a 1952 case S0 tractor. a pennsylvaning meteor rgarden tractor and sevrial cub cadets.
Location: Hubbard Ohio

Re: Carb Woes

Postby Clark Thompson » Wed Jan 09, 2013 4:20 pm

Had a few act like that over the years. found out the gasket between the two halves of the carb was rubbing on the float keeping the float from closing the needle valve properly. also had two carbs over the years with hair line cracks where the needle seat screws in.
Collector of Farmall cubs and cub cadets.Injoy helping people keep their cubs running. Years of experipnce.

Jim Becker
Team Cub
Team Cub
Posts: 13466
Joined: Sun Feb 02, 2003 2:59 pm
Zip Code: 55319
Circle of Safety: Y
Location: MN

Re: Carb Woes

Postby Jim Becker » Wed Jan 09, 2013 4:58 pm

There are some suggestions in this thread.

User avatar
Cub Pro
Cub Pro
Posts: 28706
Joined: Sun Feb 02, 2003 8:37 pm
Zip Code: E1A7J3
Skype Name: R.H. "Rudi" Saueracker, SSM
Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger
Circle of Safety: Y
Twitter ID: Rudi Saueracker, SSM
Location: NB Dieppe, Canada

Re: Carb Woes

Postby Rudi » Thu Jan 10, 2013 10:47 am


Hengy wrote:My problem is compounded by the fact that the valve on my fuel bowl is apparently bad as well, so I can't stop my little drip!

The fix for that is twofold.

#1. Repack you valve. Not too difficult. Should last for a long time when done correctly.

#2. Replace that valve with a ball valve. Poof :shock: no more problems. :idea: :) Since I replaced Ellie's I have not had a leak from my fuel sediment bowl valve, period.

It isn't exactly an original part but then again neither is the new gas cap. Just makes sense, at least to me.
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship

  • Similar Topics
    Last post

Return to “Farmall Cub”

Who is online

Users browsing this forum: No registered users and 3 guests