oil pressure high

Farmall Cub Forum -- Questions and answers to all of your Cub related issues.

Moderator: Team Cub

Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.

oil pressure high

Postby frankmarks » Mon Jan 21, 2013 12:22 pm

I recently bought a 1952 Cub and noticed my oil pressure is all the way in the white zone of mh gouge is this normal??
frankmarks
 
Posts: 17
Joined: Mon Jan 21, 2013 12:18 pm
Zip Code: 18058

Re: oil pressure high

Postby RaymondDurban » Mon Jan 21, 2013 1:03 pm

Welcome to the Forum!

What weight oil are you running? Does the pressure drop at all after the engine is warmed up?
User avatar
RaymondDurban
Team Cub Mentor
Team Cub Mentor
 
Posts: 4171
Joined: Wed Dec 26, 2007 7:45 pm
Location: CO, Peyton
Zip Code: 80831
Circle of Safety Award
Circle of Safety: Y

Re: oil pressure high

Postby Boss Hog » Mon Jan 21, 2013 2:19 pm

Either you have a bad gauge or the relief valve is stuck , If the pressure does not drop back some after it has wormed up.
IN GOD WE TRUST
All others pay cash
Boss Hog
Power corrupts; absolute power corrupts absolutely byJohn Emerich Edward Dalberg

8th Va fest link viewtopic.php?f=8&t=81392&p=657790#p657790
User avatar
Boss Hog
Cub Pro
Cub Pro
 
Posts: 9662
Joined: Mon Oct 24, 2005 8:35 pm
Location: VA. Randolph
Zip Code: 23962
eBay ID: dmb2613
Circle of Safety Award
Circle of Safety: Y

Re: oil pressure high

Postby frankmarks » Mon Jan 21, 2013 4:38 pm

Hi people,

My gauge does drop down after i shut it off,what worries me is that i dont remember it being that high when i bought the tractor. I since changed the filter and oil (30w) and its still high should i be concerned?
frankmarks
 
Posts: 17
Joined: Mon Jan 21, 2013 12:18 pm
Zip Code: 18058

Re: oil pressure high

Postby Eugene » Mon Jan 21, 2013 5:30 pm

Easy no cost check for stuck oil pressure regulator valve. Start engine and get oil pressure up. Stop engine. Remove the cap on the oil pressure regulator, remove the spring. Replace the cap.

Start engine at low idle, observe the oil pressure gauge for 15 to 20 seconds. Stop engine. Remove the cap to the oil pressure regulator valve. If valve is now located in the back of the bore, next to the cap, valve is not stuck. Could be that the spring has been replace with a much heavier one.

In case the valve is stuck. Post back, we have a valve removal method/tool.

Although once functioning, the valves seldom stick when the tractor has been relatively frequently operated.

My guess is the fault is the oil pressure gauge.
I have an excuse. CRS.
Eugene
Team Cub Mentor
Team Cub Mentor
 
Posts: 12132
Joined: Fri Jul 02, 2004 9:52 pm
Location: Mo. Linn
Zip Code: 65051
Circle of Safety Award
Circle of Safety: Y

Re: oil pressure high

Postby frankmarks » Mon Jan 21, 2013 5:33 pm

Where is the oil pressure valve located?? sorry im new to this and my tractor, but learning quickly... pictures are helpfull to!!
frankmarks
 
Posts: 17
Joined: Mon Jan 21, 2013 12:18 pm
Zip Code: 18058

Re: oil pressure high

Postby RaymondDurban » Mon Jan 21, 2013 5:44 pm

Front right side of the engine, behind a "hex cap", just above the water inlet line.
Tried to final a photo that pointed it out, but had no luck.
User avatar
RaymondDurban
Team Cub Mentor
Team Cub Mentor
 
Posts: 4171
Joined: Wed Dec 26, 2007 7:45 pm
Location: CO, Peyton
Zip Code: 80831
Circle of Safety Award
Circle of Safety: Y

Re: oil pressure high

Postby frankmarks » Mon Jan 21, 2013 5:52 pm

Thanks Ray still not sure were that is,near the radiator?? sorry im not clear on were its at.
frankmarks
 
Posts: 17
Joined: Mon Jan 21, 2013 12:18 pm
Zip Code: 18058

Re: oil pressure high

Postby Jim Becker » Mon Jan 21, 2013 5:58 pm

It is the hex cap on the right in this picture. (Picture from TM Tractor Parts.)

Image
User avatar
Jim Becker
Team Cub
Team Cub
 
Posts: 11853
Joined: Sun Feb 02, 2003 3:14 pm
Location: TX/MN
Zip Code: 75048
Circle of Safety Award
Circle of Safety: Y

Re: oil pressure high

Postby Boss Hog » Mon Jan 21, 2013 6:03 pm

You would do well to look at the manuals, they are at the [ NEW ] Manuals link at the left top of the page.
IN GOD WE TRUST
All others pay cash
Boss Hog
Power corrupts; absolute power corrupts absolutely byJohn Emerich Edward Dalberg

8th Va fest link viewtopic.php?f=8&t=81392&p=657790#p657790
User avatar
Boss Hog
Cub Pro
Cub Pro
 
Posts: 9662
Joined: Mon Oct 24, 2005 8:35 pm
Location: VA. Randolph
Zip Code: 23962
eBay ID: dmb2613
Circle of Safety Award
Circle of Safety: Y

Re: oil pressure high

Postby frankmarks » Mon Jan 21, 2013 6:30 pm

ok great pic now i just need to locate that item and shall i try what you suggested then?
frankmarks
 
Posts: 17
Joined: Mon Jan 21, 2013 12:18 pm
Zip Code: 18058

Re: oil pressure high

Postby RaymondDurban » Mon Jan 21, 2013 6:46 pm

Remove that hex bolt, and behind it will be a spring. This spring pushes against a plug and is what regulates the pressure. If the plug is stuck, there will be no relief and it will cause high oil pressure.
Open it up and have a look. If its stuck and you can't get it out with a magnet on a stick, come back and we'll show you a trick to get it out and cleaned up.
User avatar
RaymondDurban
Team Cub Mentor
Team Cub Mentor
 
Posts: 4171
Joined: Wed Dec 26, 2007 7:45 pm
Location: CO, Peyton
Zip Code: 80831
Circle of Safety Award
Circle of Safety: Y

Re: oil pressure high

Postby frankmarks » Mon Jan 21, 2013 7:19 pm

Ok great so, far Im a cnc machinist so this will be fun. Love to see your trick...
frankmarks
 
Posts: 17
Joined: Mon Jan 21, 2013 12:18 pm
Zip Code: 18058

Re: oil pressure high

Postby RaymondDurban » Mon Jan 21, 2013 7:26 pm

User avatar
RaymondDurban
Team Cub Mentor
Team Cub Mentor
 
Posts: 4171
Joined: Wed Dec 26, 2007 7:45 pm
Location: CO, Peyton
Zip Code: 80831
Circle of Safety Award
Circle of Safety: Y

Re: oil pressure high

Postby frankmarks » Mon Jan 21, 2013 8:14 pm

If i try this and i still have high pressure is it safe to run,also if i push on this wooden dowel i will not push anything into the motor will i? Thanks for all your help if i try and it doesnt work i hope its good to drive...
frankmarks
 
Posts: 17
Joined: Mon Jan 21, 2013 12:18 pm
Zip Code: 18058

Next

Return to Farmall Cub

Who is online

Users browsing this forum: Daniel H., Glen, jpcubs, Lee_Petrie, Tom and 3 guests