Hi All,
I would appreciate any suggestions as to where I can purchase a centrifugal type starter bendix. Please refer to the "starter bendix" post (using the search window) that was posted here on September 17, 2012 at 10:59am. In that post, the two different types of starter gears are pictured. My timing is right, my condenser is new, but when it is cold the engine needs a couple of full turns before it fires up and stays running. My spring type starter gear kicks out too early.
I tried ordering one from NAPA auto parts - but they only acquired the spring type. The NAPA parts guy said that both types have the same part number (is that true?). I am thinking that I might have to go to a tractor boneyard - but I would much rather purchase a brand new one.
Am I correct that both types fit on the same starter shaft?
Any suggestions would be greatly appreciated.
Thanks!
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
starter bendix - want to purchase centrifugal
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 379
- Joined: Sun Dec 12, 2004 9:29 pm
- Location: st. paul, mn
starter bendix - want to purchase centrifugal
Rick 1948 cub
- Mike in Louisiana
- 10+ Years
- Posts: 7812
- Joined: Tue Feb 15, 2005 10:10 am
- Zip Code: 71023
- Circle of Safety: Y
- Location: LA, Doyline
Re: starter bendix - want to purchase centrifugal
Check wih your local auto elec repair. The place that repairs alt, generators and starters.
1975 cub (LouAnn) serial # 245946, 1941 John Deere Model H
Good judgment comes from experience,
and a lot of that comes from bad judgment. Will Rogers
Good judgment comes from experience,
and a lot of that comes from bad judgment. Will Rogers
- challenger
- 10+ Years
- Posts: 1087
- Joined: Sun Apr 18, 2010 6:22 am
- Zip Code: 21742
- Tractors Owned: 1955 F Cub (2)
1952 F Cub
1948 F Cub
2155 JD
216 JD - Circle of Safety: Y
- Location: Hagerstown MD
Re: starter bendix - want to purchase centrifugal
The Cub starter has a screw or worm gear housing that slides over the starter drive shaft. A flat coiled spring connects the starter shaft to the worm gear housing. The starter gear is moved outward on the worm to engage the ring gear by the principle of inerta working with the sudden rotation of the starting motor. The coiled spring cushions the impact to the starter motor when the worm gear meshes with the ring gear.
-
- Team Cub Mentor
- Posts: 20344
- Joined: Fri Jul 02, 2004 9:52 pm
- Zip Code: 65051
- Circle of Safety: Y
- Location: Mo. Linn
Re: starter bendix - want to purchase centrifugal
The only time the starter bendix, over running clutch, will kick out is when the engine in turning faster than the starter. Double check engine timing - full engine tune up.rick 48 cub wrote:My timing is right, my condenser is new, but when it is cold the engine needs a couple of full turns before it fires up and stays running. My spring type starter gear kicks out too early.
I have an excuse. CRS.
- challenger
- 10+ Years
- Posts: 1087
- Joined: Sun Apr 18, 2010 6:22 am
- Zip Code: 21742
- Tractors Owned: 1955 F Cub (2)
1952 F Cub
1948 F Cub
2155 JD
216 JD - Circle of Safety: Y
- Location: Hagerstown MD
Re: starter bendix - want to purchase centrifugal
As Eugene says the timing, not the starter is the most likely culprit. Your starter spring would not cause the problem. Your spark is likely retarded, meaning the spark is delayed and firing after TDC. Forget the dynamic timing with the light. Do a static time on the engine. Make sure the points open and spark occur on number one cylinder right at the TDC mark on the crank pulley. The distributor has a centrifugal weight system to give you the proper advance as the engine rpm increases. Also, make sure you have not mistakenly switched the spark plug wires on the plugs. When looking at the open distributor, number one terminal/plug on the inside of the cap is at 1 o'clock and the rotor turns clockwise to fire plugs 1342.
-
- 10+ Years
- Posts: 1172
- Joined: Tue Oct 19, 2004 7:10 am
- Zip Code: 29130
- Tractors Owned: fcub(5)
tricycle cub
154 (4)
Earthmaster (2)
JD 40T, JD 420 crawler-loader, JD MT
JD Unstyled A, Styled A, Unstyled AR
JD H
Centaur Tractor
AC Model C, G
Cub Cadets (9)
Gibson D
Red-E - Circle of Safety: Y
- Location: SC, Ridgeway
Re: starter bendix - want to purchase centrifugal
Different versions of that type of starter drive, folo-thru is one type. I have no idea where to get one other than ebay or a starter shop.
I would do as others suggested, tune the engine. I will disagree with Challenger, do dynamic timing with a light, more info than through static timing. Check to see if the advance is working by using the light.
I would do as others suggested, tune the engine. I will disagree with Challenger, do dynamic timing with a light, more info than through static timing. Check to see if the advance is working by using the light.
Who is online
Users browsing this forum: No registered users and 28 guests