parts estimate

Farmall Cub Forum -- Questions and answers to all of your Cub related issues.

Moderator: Team Cub

Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
southernthunder
5+ Years
5+ Years
Cub Star
Cub Star
Posts: 84
Joined: Thu Mar 12, 2009 8:55 pm
Zip Code: 28430
Tractors Owned: 1950 Cub (Family Bought New)
1950 Cub
1950 TO-20

Re: parts estimate

Postby southernthunder » Mon Mar 11, 2013 11:02 pm

Update: after a lot of searching the web and such for crossover numbers I finally got almost everything ordered for my tranny/ final drive rebuild. the only bearing I have not got as a Timken replacement was the front spline shaft (it was another brand) and the rear spline shaft bearing. I have skf,new departure,agco,ntn and several more cross numbers that will work if I slightly reduce the diameter of the shaft that goes in it. I found this info in an old post here because several people were having trouble due to wear on the shaft from the original rollers direct on shaft. Sounds like a good cheaper fix to tighten this up. Total is looking like about $500 which includes doubling each seal where there is room. Any suggestions on anything else I may need to replace while in it. I have all the seals, gaskets and bearings I can find in the parts book. just hoping to have everything in the shop when I start the rebuild. thanks guys

User avatar
bob in CT
Team Cub Mentor
Team Cub Mentor
501 Club
501 Club
Posts: 5974
Joined: Thu Jun 07, 2007 9:34 am
Zip Code: 06040
Tractors Owned: 77 Cub (red); 74 Cub; 52 Cub; 50 Cub ( post-demo)
Circle of Safety: Y
Location: CT, Manchester

Re: parts estimate

Postby bob in CT » Tue Mar 12, 2013 4:46 am

Someone on this board commented that using 2 seals was not a good idea. The seals are designed to run wet. The outside seal will wear quickly and just become a dirt trap that will degrade the inner seal. Better to use the thinner seal to choose a clean, unworn spot on the shaft to do its job.

southernthunder
5+ Years
5+ Years
Cub Star
Cub Star
Posts: 84
Joined: Thu Mar 12, 2009 8:55 pm
Zip Code: 28430
Tractors Owned: 1950 Cub (Family Bought New)
1950 Cub
1950 TO-20

Re: parts estimate

Postby southernthunder » Tue Mar 12, 2013 5:42 am

thanks for the imput bob. all of the research I found on here suggested to use 2 seals in the place of some of the original double seal (rubber and leather). Maybe I should start another thread and ask everyone what they think. If that's the case I will have a start on parts for my next project :D thanks

User avatar
bob in CT
Team Cub Mentor
Team Cub Mentor
501 Club
501 Club
Posts: 5974
Joined: Thu Jun 07, 2007 9:34 am
Zip Code: 06040
Tractors Owned: 77 Cub (red); 74 Cub; 52 Cub; 50 Cub ( post-demo)
Circle of Safety: Y
Location: CT, Manchester

Re: parts estimate

Postby bob in CT » Tue Mar 12, 2013 6:56 am

If memory serves me, it was Steve K. Calif that posted this. He is a bearing and seal professional.

southernthunder
5+ Years
5+ Years
Cub Star
Cub Star
Posts: 84
Joined: Thu Mar 12, 2009 8:55 pm
Zip Code: 28430
Tractors Owned: 1950 Cub (Family Bought New)
1950 Cub
1950 TO-20

Re: parts estimate

Postby southernthunder » Tue Mar 12, 2013 7:04 am

with all of the input I received so quickly on the new post, and from your suggestion, I will only be putting a single seal in the most appropriate, smoothest spot on the shaft for each location.. thanks so much, mike

User avatar
bob in CT
Team Cub Mentor
Team Cub Mentor
501 Club
501 Club
Posts: 5974
Joined: Thu Jun 07, 2007 9:34 am
Zip Code: 06040
Tractors Owned: 77 Cub (red); 74 Cub; 52 Cub; 50 Cub ( post-demo)
Circle of Safety: Y
Location: CT, Manchester

Re: parts estimate

Postby bob in CT » Tue Mar 12, 2013 7:24 am

You will like the sealed bearing fix for the input shaft. I did that for my 1950 Cub project and I was very pleased with the results.

southernthunder
5+ Years
5+ Years
Cub Star
Cub Star
Posts: 84
Joined: Thu Mar 12, 2009 8:55 pm
Zip Code: 28430
Tractors Owned: 1950 Cub (Family Bought New)
1950 Cub
1950 TO-20

Re: parts estimate

Postby southernthunder » Tue Mar 12, 2013 7:57 am

that's my plan for it and the pto bearing. if the replacements come sealed, I am just going to leave them that way. It should last me or my girls or whoever they sell it to when I am gone.


Return to “Farmall Cub”

Who is online

Users browsing this forum: wrz and 8 guests