This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Defective head bolt
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 26
- Joined: Sun Mar 31, 2013 4:34 pm
- Zip Code: 06488
Defective head bolt
I went out and bought some Grade 5 bolts to replace my head bolts. I torqued them all to 20 flb and started over to take them to 40. The center bolt tightened to 40 and I moved on to the second bolt in the sequence and it snapped off. So either the bolt was defective or I should be using grade 8s. The bolt in question was a Hillman Grade 5. I already drilled and extracted the broken bolt. Should I get a set of Grade 8 or do they not have enough stretch?
- John *.?-!.* cub owner
- Cub Pro
- Posts: 23701
- Joined: Sun Feb 02, 2003 2:09 pm
- Zip Code: 63664
- Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
- Location: Mo, Potosi
Re: Defective head bolt
Those are 3/8 bolts, and according to the chart in the front of the service manual torque on a grade 5 bolt is maximum of 37 ft lbs.
If you are not part of the solution,
you are part of the problem!!!
you are part of the problem!!!
-
- 10+ Years
- Posts: 26
- Joined: Sun Mar 31, 2013 4:34 pm
- Zip Code: 06488
Re: Defective head bolt
HMMM.. So the replacement bolts on Farmall forever are grade 8 SAE J429, but if you look those up on a torque chart max torque dry install is 44 ft lb. The head specs say 45 ft lbs, so even with factory bolts we are at max torque?
- John *.?-!.* cub owner
- Cub Pro
- Posts: 23701
- Joined: Sun Feb 02, 2003 2:09 pm
- Zip Code: 63664
- Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
- Location: Mo, Potosi
Re: Defective head bolt
that is the way I read it. don't forget to use some thread sealing compound on the threads to prevent water leaks, which also acts as a lubricant so you need to use less than 45 lbs for torque, max 40 or a little less.
If you are not part of the solution,
you are part of the problem!!!
you are part of the problem!!!
-
- 10+ Years
- Posts: 26
- Joined: Sun Mar 31, 2013 4:34 pm
- Zip Code: 06488
Re: Defective head bolt
I went to my local Case IH dealer today and spoke with their Mechanic about replacement head bolts. His advice is to reuse the old bolts. He said any head work they do on older tractors they either reuse the existing head bolts or find used replacements. He said none of the newer manufactured stuff today is up to par with the original bolts.
- Rudi
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger - Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
- Contact:
Re: Defective head bolt
I used to reuse the old bolts, that is what my IH mechanic told me to do a number of years ago. Clean em up, put never seize on them and re-install. I will no longer do that. 60 + year old bolts have done their job and time to retire them. I can get exact length replacements from my local fastener supply house that I have dealt with for almost 30 years. Grade 8 bolts. Reusing old bolts does have a few risks .... in my book not worth taking. I redid the head on my '48 3 times. The last time I put in the new head bolts.
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship
-
- 10+ Years
- Posts: 4948
- Joined: Tue Jun 08, 2004 3:04 pm
- Zip Code: 14559
- Circle of Safety: Y
- Location: Rochester, NY
Re: Defective head bolt
Aren't the head bolts supposed to be grade 9?
-
- 10+ Years
- Posts: 804
- Joined: Tue Apr 17, 2012 7:55 pm
- Zip Code: 47119
- Skype Name: ntrenn
- Tractors Owned: 63 Cub 221833 in family since '69
65 Lo-boy 19648 with an un-stuck #4 - it lives!!!
144 Cultivators with disc hillers
193 Plow
42C mower
59L mower mounted on the Fcub
23A Disc - lost possession - Circle of Safety: Y
- Location: Indiana
Re: Defective head bolt
You have 2 options with new bolts....either use Grade 8 and drop the torque back to 40 ft-lb, which works just fine, or go with Grade 9 and keep the torque at 45 per the book. Reusing head bolts on a 50 year old engine is more risky in my book than using modern bolts. I went with plated Grade 8 with washers on my last build and so far it's doing just fine. I also did NOT retorque after running the engine.
- bob in CT
- Team Cub Mentor
- Posts: 6018
- Joined: Thu Jun 07, 2007 9:34 am
- Zip Code: 06040
- Tractors Owned: 77 Cub (red); 74 Cub; 52 Cub; 50 Cub ( post-demo)
- Circle of Safety: Y
- Location: CT, Manchester
Re: Defective head bolt
I have a tractor that came with a professionally rebuilt engine. It was weeping coolant. I replaced that head gasket and re-torqued- no problems. 15 years ago I rebuilt my 52 and same procedure and no leaks. I run it with a pony tank so it only takes a few minutes.
Make sure your aftermarket bolts are trimmed or use grade 8 washers. Too long and the threads extend into the coolant and they will be a bear to get out someday. I like Rectorseal PTFE paste for sealing the threads to prevent coolant weep up the threads. Others use Indian Head shellac with good results- choose your poison, but choose one for sure! I agree with using grade 9 at 45 and grade 8 at 40 ft-lbs. Original bolts were clearly better than grade 8.
Make sure your aftermarket bolts are trimmed or use grade 8 washers. Too long and the threads extend into the coolant and they will be a bear to get out someday. I like Rectorseal PTFE paste for sealing the threads to prevent coolant weep up the threads. Others use Indian Head shellac with good results- choose your poison, but choose one for sure! I agree with using grade 9 at 45 and grade 8 at 40 ft-lbs. Original bolts were clearly better than grade 8.
- bob in CT
- Team Cub Mentor
- Posts: 6018
- Joined: Thu Jun 07, 2007 9:34 am
- Zip Code: 06040
- Tractors Owned: 77 Cub (red); 74 Cub; 52 Cub; 50 Cub ( post-demo)
- Circle of Safety: Y
- Location: CT, Manchester
Re: Defective head bolt
I bought my grade 9 bolts from McMaster Carr for my 1950 engine work. Grade 9 are significantly stronger than grade 8 and because of the higher tensile strength, the heads of the bolts are thicker. I need to trim all the bolt just a little so I was making sure there were enough threads on the bolt. When I had them side-by-side, I noticed the IH bolts had the same head thickness as the new grade 9's. For comparison, I put a grade 8 in the picture. I am ONLY using grade 9 bolts as replacements for IH head bolts. The IH torque spec exceeds that of grade 8 and the extra thickness of the head of the bolt clinched it for me.
- Attachments
-
- IH head bolt, grade 8 bolt and grade 9 bolt comparison
- IMG_1682.JPG (215.95 KiB) Viewed 1460 times
-
- 10+ Years
- Posts: 1573
- Joined: Sun Feb 02, 2003 11:01 pm
- Zip Code: 36310
- Tractors Owned: 1975 IH cub,1948 farmall cub,1979 international 3200 skid steer and a 1974 John deere 350B dozer.
- Location: Abbeville Alabama
Re: Defective head bolt
I have never had any problems re using the original head bolts providing they were not pitted or rusted. It is very important to clean the threads on the bolts plus in the block. On all the cub engines I rebuild I torque head bolts to 45 then after a couple hrs running I re torque them to 45. With heat the head gasket seems to shrink. I do know the new bolts are not like the originals. Failure is high with the new bolts. Even grade 8. It also depends on where the bolts were made. USA made is pretty good but anyting from china or japan is junk. Tractor supply has a selection of bolts but most are china junk.
Collector of Farmall cubs and cub cadets.Injoy helping people keep their cubs running. Years of experipnce.
- ricky racer
- 10+ Years
- Posts: 6334
- Joined: Wed Sep 12, 2007 8:40 pm
- Zip Code: 49120
- Circle of Safety: Y
- Location: Niles / Buchanan, Michigan
Re: Defective head bolt
That's a great comparison Bob. My concern has never been the bolt strength. I lube the bolts with some type of sealant which reduces the torque required to achieve the same tension. My concern has always been the threads stripping out due to the limited engagement area and the soft cast iron threads. I've Heli-Coiled every bolt hole that secures the head after stripping out the threads on one hole torquing the head.
1929 Farmall Regular
1935 John Deere B
1937 John Deere A
1941 John Deere H
1952 John Deere B
1953 Farmall Cub
1935 John Deere B
1937 John Deere A
1941 John Deere H
1952 John Deere B
1953 Farmall Cub
-
- 10+ Years
- Posts: 59
- Joined: Thu Mar 07, 2013 7:35 pm
- Zip Code: 74604
Re: Defective head bolt
If I had read this post 2 weeks ago I would have went with grade 9 bolts,used grade 8 from fastenal,Torqued to 45 and used sealant on threads on this restored 48 Cub,Head gasket was seaping antifreeze down side of engine causing paint to lift.
- bob in CT
- Team Cub Mentor
- Posts: 6018
- Joined: Thu Jun 07, 2007 9:34 am
- Zip Code: 06040
- Tractors Owned: 77 Cub (red); 74 Cub; 52 Cub; 50 Cub ( post-demo)
- Circle of Safety: Y
- Location: CT, Manchester
Re: Defective head bolt
If you did not feel the bolts yield when torquing, you should be OK. I had a weeper just like you described and found at least one bolt was weeping coolant right up the threads. I made sure to re-torque after running it up to full temperature and cooling it down and the bolts did take up a little more. High and dry since.
-
- 10+ Years
- Posts: 7388
- Joined: Sat Jul 22, 2006 5:02 pm
- Zip Code: 00000
- Location: in northern usa
Re: Defective head bolt
Being a engine builder for drag racing back in the early days I delt with high compression highly tuned engine idling between 1,200 to 1,800 rpm. Can cause problems with over heating if we don't assemble it correctly.
Here's my assembly process on every engine;
1. Wire wheel every head bolt squeaky clean.
2. Apply the high tac red spray sealer to both sides of the head gasket.
3. I cut the head .010" to make sure it's flat. I also check the deck of the block for flatness too with a starret straight edge.
4. I apply permatex #2 to each head bolt thread so the threads are sealed and the coolant can't weep up past the threads. Of you look closely when disassembling the head bolts the factory during assembly did this too by the old sealer caked on the head bolts.
5. I then follow the torque specs specs and I add 10lbs. Of torque to the specs. Then I run the engine then retorque in a few days after some operation.
I learned this though experience. Bill
Here's my assembly process on every engine;
1. Wire wheel every head bolt squeaky clean.
2. Apply the high tac red spray sealer to both sides of the head gasket.
3. I cut the head .010" to make sure it's flat. I also check the deck of the block for flatness too with a starret straight edge.
4. I apply permatex #2 to each head bolt thread so the threads are sealed and the coolant can't weep up past the threads. Of you look closely when disassembling the head bolts the factory during assembly did this too by the old sealer caked on the head bolts.
5. I then follow the torque specs specs and I add 10lbs. Of torque to the specs. Then I run the engine then retorque in a few days after some operation.
I learned this though experience. Bill
I'm technically misunderstood at times i guess its been this way my whole life so why should it change now.
Who is online
Users browsing this forum: No registered users and 41 guests