A Video on what The clutch in my Cub has been doing
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Clutch.
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
- Brendan In NC
- 10+ Years
- Posts: 440
- Joined: Fri Jul 29, 2011 6:54 pm
- Zip Code: 27858
- Tractors Owned: 1964 Farmall Cub Red Square Nose # 223883 one of 2300 built before they switch to Yellow and White.
1964 Farmall 140 #27512
Just a Clean Strong run of the mill Farmall 140 with very little Wear.
Also have a bit of equipment
Woods C-42 Belly mower, 1963 IH McCormick #215 Plow, IH #144 Cultivators, IH Side Dresser (in need of some work non working at the moment) - Location: Greenville N.C
- Contact:
Clutch.
Tractors are like watermelons..Eat the red and throw away the green!!
Brendan Dixon Greenville NC
1964 Farmall Cub #223883
1964 Farmall 140 #27512
Tractorguy140, YouTube
Brendan Dixon Greenville NC
1964 Farmall Cub #223883
1964 Farmall 140 #27512
Tractorguy140, YouTube
-
- 10+ Years
- Posts: 1224
- Joined: Wed Jul 02, 2008 6:11 am
- Location: MN, Mankato
Re: Clutch.
That should be an easy adjustment. The clutch pedal that you are pushing needs reset. There are instructions in the manuals for the range of motion, engagement, and full travel of the pedal.
Todd
Todd
-
- Team Cub Mentor
- Posts: 20370
- Joined: Fri Jul 02, 2004 9:52 pm
- Zip Code: 65051
- Circle of Safety: Y
- Location: Mo. Linn
Re: Clutch.
I'm going for worn out throwout bearing. Sounds like the throwout bearing bracket is hitting the pressure plate fingers.
Check for throwout bearing condition and pressure plate finger height.
Check for throwout bearing condition and pressure plate finger height.
I have an excuse. CRS.
-
- 10+ Years
- Posts: 1421
- Joined: Sun Apr 30, 2006 2:54 pm
- Zip Code: 60073
- Circle of Safety: Y
- Location: IL, Round Lake Heights
Re: Clutch.
You need to adjust the pressure plate fingers. I had that exact same noise after splitting my cub to replace the rear main. I figured while I her split, I'd adjust the fingers where I could get at them directly, rather than through the hand hole. Unfortunately, I forgot that they are supposed to be checked with the pressure plate bolted to the flywheel, so, of course, they [url]weren't[/url] properly adjusted after all. (I should have figured something was wrong when they measured so far off, even though I had no problem before splitting .)
Got her back together, and got that same noise. Adjusted the fingers again (through the hand hole, this time), and she was fine. Adjust the fingers first, then adjust the free play so you have the proper clearance between the TOB and the fingers. A paint stirrer is the perfect thickness for setting the clearance.
Got her back together, and got that same noise. Adjusted the fingers again (through the hand hole, this time), and she was fine. Adjust the fingers first, then adjust the free play so you have the proper clearance between the TOB and the fingers. A paint stirrer is the perfect thickness for setting the clearance.
Michael Cummings
Eddie - a 1959 International Lo-Boy named after my father in law, who who bought her new.
Eddie - a 1959 International Lo-Boy named after my father in law, who who bought her new.
- Boss Hog
- Cub Pro
- Posts: 10290
- Joined: Mon Oct 24, 2005 8:35 pm
- Zip Code: 23962
- eBay ID: dmb2613
- Circle of Safety: Y
- Location: VA. Randolph
Re: Clutch.
Drag that cub up here well will take care of it , you are about 3 hours away Brendan
Boss
Boss
IN GOD WE TRUST
All others pay cash
Boss Hog
Power corrupts; absolute power corrupts absolutely byJohn Emerich Edward Dalberg
All others pay cash
Boss Hog
Power corrupts; absolute power corrupts absolutely byJohn Emerich Edward Dalberg
- Brendan In NC
- 10+ Years
- Posts: 440
- Joined: Fri Jul 29, 2011 6:54 pm
- Zip Code: 27858
- Tractors Owned: 1964 Farmall Cub Red Square Nose # 223883 one of 2300 built before they switch to Yellow and White.
1964 Farmall 140 #27512
Just a Clean Strong run of the mill Farmall 140 with very little Wear.
Also have a bit of equipment
Woods C-42 Belly mower, 1963 IH McCormick #215 Plow, IH #144 Cultivators, IH Side Dresser (in need of some work non working at the moment) - Location: Greenville N.C
- Contact:
Re: Clutch.
Ok im gonna try both next time out but which would be the clutch finger's? (dummy over here)
Tractors are like watermelons..Eat the red and throw away the green!!
Brendan Dixon Greenville NC
1964 Farmall Cub #223883
1964 Farmall 140 #27512
Tractorguy140, YouTube
Brendan Dixon Greenville NC
1964 Farmall Cub #223883
1964 Farmall 140 #27512
Tractorguy140, YouTube
- tmays
- 10+ Years
- Posts: 3410
- Joined: Wed May 11, 2011 8:59 pm
- Zip Code: 39154
- Tractors Owned: 1969 Farmall Cub
1952 Cub
1942 Farmall H - Location: Raymond, MS
Re: Clutch.
The fingers are the three things with the slots in them held in place with the nuts.
Thomas
- Dale Finch
- 10+ Years
- Posts: 6677
- Joined: Tue Apr 27, 2010 11:34 am
- Zip Code: 27517
- Tractors Owned: '51 Cub #140966 "Bruno" with Woods 59 mower
'55 Cub #187541 "Betty" with Fast Hitch
'55 Cub #190482 "Ben" with Woods 42 mower
'55 Cub #191739 "Bertha" with Woods 42 mower
'56 Cub #194370 "Boris" with Mott Flail mower - Circle of Safety: Y
- Location: NC, Chapel Hill
Re: Clutch.
Like Boss said, take it up there and he will have that thing humming!!
I had the same thing happen. Had to adjust the fingers, THEN set the peddle adjustment. But I found I had to make it just a tad more freeplay in the peddle than the manual said or I would get the TOB carrier hitting the adjustment screws (TOB was fairly new and in good shape). Don't run it like that or you won't have any screws left to adjust! Good luck.
PS You are welcome to bring it over to Chapel Hill for a minifest...I have to remove my left final for a brake job and will go ahead and replace seals while I am at it. We could get both done at the same time!
I had the same thing happen. Had to adjust the fingers, THEN set the peddle adjustment. But I found I had to make it just a tad more freeplay in the peddle than the manual said or I would get the TOB carrier hitting the adjustment screws (TOB was fairly new and in good shape). Don't run it like that or you won't have any screws left to adjust! Good luck.
PS You are welcome to bring it over to Chapel Hill for a minifest...I have to remove my left final for a brake job and will go ahead and replace seals while I am at it. We could get both done at the same time!
Who is online
Users browsing this forum: No registered users and 46 guests