This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy

NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.

Bull gear and the Bull Head

The Cub Club -- Questions and answers to all of your Cub related issues.
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Post Reply
User avatar
pickerandsinger
10+ Years
10+ Years
Posts: 1501
Joined: Thu Oct 18, 2012 3:23 pm
Zip Code: 13143
Tractors Owned: 1957 Cub Low Boy w/ FH Mott Flail Mower
1953 Cub w/ sprayer and 54A blade (Chompers)
1954 Cub w/fast hitch (Ira)
1948 Cub ( Papa Paul)with Henderson loader..
1951 Mutt mix Cub (BattleAx
1950 Farmall Cub (basket case demo)
Cub parts tractor
2019 " KuB"ota 2601 loader and roto tiller
1951 Ferguson TEA 20 (parts)( Uncle Rusty)
F/H Disc Harrow for cub L-38
C-22 Sickle Bar Mower
IH C2 and C3 mower
Universal tool attachment with disc hillers..Rear cultivators (various tips
York Rake for Cub home made
Single bottom Plow for Cub F194
Gravely 5660 12 hp/ w snoblower.rototiller,bush hog
Circle of Safety: Y

Bull gear and the Bull Head

Postby pickerandsinger » Wed May 15, 2013 11:12 pm

Took off the sickle bar mower....Went fine till I got to the pulley...Broke that, and the spline was shot on the Pto...Had an extra shaft, so I redid the Pto and re-installed it....Got the IH C-2 in place and proceeded to try to figure out the Bull Gear install....Finally took the drawbar apart, and jacked the bull gear up and partially started the bolts...Installed the plates from the drawbar on the partially started bolts, between the bull gear and the finals and manipulated the drawbar back in place and bolted the whole thing together using 5/8 by 2 inch with an extra nut and lock washers on the bull drive so it would equal the 1 1/4.the manual called for....Then proceeded to bolt the mower brackets in place on the bull gear, with 1/2 inch grade 8's and lock nuts, so it would move freely..Very limited space for the fingers I might add....I had previously attached the lift chain and bar, so I started to install the belt but alas it is to short...I need to move the mower back a few holes to make it fit....But I ran out of steam....Tomorrow is another day.....My little paragraph has taken me a day and 1/2...And yes I had several failed variations of the project.and I need to figure out the picture thing one of these days.... :bellylaugh: Say goodnight, Dave...Thanks to everyone who precipitated....
In Memory of 58,286
Top

SPONSOR AD

Sponsor

Sponsor
 
Top
User avatar
pickerandsinger
10+ Years
10+ Years
Posts: 1501
Joined: Thu Oct 18, 2012 3:23 pm
Zip Code: 13143
Tractors Owned: 1957 Cub Low Boy w/ FH Mott Flail Mower
1953 Cub w/ sprayer and 54A blade (Chompers)
1954 Cub w/fast hitch (Ira)
1948 Cub ( Papa Paul)with Henderson loader..
1951 Mutt mix Cub (BattleAx
1950 Farmall Cub (basket case demo)
Cub parts tractor
2019 " KuB"ota 2601 loader and roto tiller
1951 Ferguson TEA 20 (parts)( Uncle Rusty)
F/H Disc Harrow for cub L-38
C-22 Sickle Bar Mower
IH C2 and C3 mower
Universal tool attachment with disc hillers..Rear cultivators (various tips
York Rake for Cub home made
Single bottom Plow for Cub F194
Gravely 5660 12 hp/ w snoblower.rototiller,bush hog
Circle of Safety: Y

Re: Bull gear and the Bull Head

Postby pickerandsinger » Sun May 19, 2013 8:14 pm

Up Date....Mowed a couple acres with it today...How the heck I managed to chonk up a Bull Frog ( I swear its the truth)....But I did...He was huge...So now its Bull Head, Bull Gear, and the Bull Frog
In Memory of 58,286
Top
User avatar
Barnyard
Team Cub
Team Cub
Posts: 24266
Joined: Tue Aug 07, 2007 3:39 pm
Zip Code: 45030
Tractors Owned: At This Time
40 Farmall Cubs (Round Hood)
2 Farmall Cub (Square Hood)
2 IH Cubs (Square Hood)
5 Lo-Boys (Round Hood)
2 Lo-Boys (Square Hood)
2 Farmall 404's
1 Farmall H
1 Ferguson 20
1 Cub Cadet 125
1 Kubota B-7100
Circle of Safety: Y
Location: OH, New Haven (Hamilton County)
Contact:
Contact Barnyard

Re: Bull gear and the Bull Head

Postby Barnyard » Sun May 19, 2013 8:21 pm

pickerandsinger wrote:I managed to chonk up a Bull Frog ( I swear its the truth)....

We believe you Dave , but this is starting to sound like a lot of bull... :lol:
There are two ways to get enough Cubs. One is to continue to accumulate more and more. The other is to desire less.

Circle of Safety
Top
User avatar
pickerandsinger
10+ Years
10+ Years
Posts: 1501
Joined: Thu Oct 18, 2012 3:23 pm
Zip Code: 13143
Tractors Owned: 1957 Cub Low Boy w/ FH Mott Flail Mower
1953 Cub w/ sprayer and 54A blade (Chompers)
1954 Cub w/fast hitch (Ira)
1948 Cub ( Papa Paul)with Henderson loader..
1951 Mutt mix Cub (BattleAx
1950 Farmall Cub (basket case demo)
Cub parts tractor
2019 " KuB"ota 2601 loader and roto tiller
1951 Ferguson TEA 20 (parts)( Uncle Rusty)
F/H Disc Harrow for cub L-38
C-22 Sickle Bar Mower
IH C2 and C3 mower
Universal tool attachment with disc hillers..Rear cultivators (various tips
York Rake for Cub home made
Single bottom Plow for Cub F194
Gravely 5660 12 hp/ w snoblower.rototiller,bush hog
Circle of Safety: Y

Re: Bull gear and the Bull Head

Postby pickerandsinger » Mon May 20, 2013 4:46 pm

Or a lot of Goat, Bill :bellylaugh:
In Memory of 58,286
Top
Post Reply

Return to “Farmall Cub”

Who is online

Users browsing this forum: No registered users and 50 guests