This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Timing Advance?
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 41
- Joined: Tue Jun 16, 2009 5:56 pm
- Zip Code: 02536
- Circle of Safety: Y
Timing Advance?
I know, KISS, Keep it simple stupid. Well my 69 square nose starts and runs OK but had issues with running smooth and bogging down under power. Compression is within 4 points at 112 lbs. Has Pedtronix Ignitor electronic ignition, new plugs, cap, rotor, coil and wires.
Number one cylinder at TDC, pointer on bottom pulley mark. Runs a little rough at 500 rpms, not bad though. Runs the same at 1,600 rpms. With throttle set at 500 rpms, timing light shows pointer on bottom pulley mark. Run it up to 1,600 rpms, pointer stays on bottom pulley mark.
Shouldn't it move to the top pulley mark at full throttle?
What KISS little thing am I missing.[size=150][/size]
Number one cylinder at TDC, pointer on bottom pulley mark. Runs a little rough at 500 rpms, not bad though. Runs the same at 1,600 rpms. With throttle set at 500 rpms, timing light shows pointer on bottom pulley mark. Run it up to 1,600 rpms, pointer stays on bottom pulley mark.
Shouldn't it move to the top pulley mark at full throttle?
What KISS little thing am I missing.[size=150][/size]
- RaymondDurban
- Cub Pro
- Posts: 4435
- Joined: Wed Dec 26, 2007 7:45 pm
- Zip Code: 32536
- Circle of Safety: Y
- Location: FL, Crestview
Re: Timing Advance?
At idle, it should be at the top pulley mark (TDC), and full throttle it should move down to the bottom mark (16* advance).
Set the idle to the top mark first, then see what happens when you increase the throttle. If it doesn't move to the bottom mark, the check the weights in the distributor.
Set the idle to the top mark first, then see what happens when you increase the throttle. If it doesn't move to the bottom mark, the check the weights in the distributor.
Screwstick #3934
FCub - LoBoy - Numbered Series - Power Unit Databases
FCub - LoBoy - Numbered Series - Power Unit Databases
-
- Team Cub Mentor
- Posts: 20344
- Joined: Fri Jul 02, 2004 9:52 pm
- Zip Code: 65051
- Circle of Safety: Y
- Location: Mo. Linn
Re: Timing Advance?
Follow Ray's directions to see if the advance is working.
Under the rotor, in the center of the post it sits on, is suppose to be a wick. This wick is to be oiled - and usually not. If advance is not working, set engine on TDC, # 1 cylinder and remove distributor. Set distributor upright in vise or stand. Add quality solvent to the wick. Let set. See if the solvent frees up the advance.
You will only get about an 8 degree movement in the advance, not much more than a wiggle, when it frees up. When free, oil wick and move advance mechanism. Then oil weight and spring pivots.
Under the rotor, in the center of the post it sits on, is suppose to be a wick. This wick is to be oiled - and usually not. If advance is not working, set engine on TDC, # 1 cylinder and remove distributor. Set distributor upright in vise or stand. Add quality solvent to the wick. Let set. See if the solvent frees up the advance.
You will only get about an 8 degree movement in the advance, not much more than a wiggle, when it frees up. When free, oil wick and move advance mechanism. Then oil weight and spring pivots.
I have an excuse. CRS.
-
- 10+ Years
- Posts: 41
- Joined: Tue Jun 16, 2009 5:56 pm
- Zip Code: 02536
- Circle of Safety: Y
Re: Timing Advance?
Thank you, I'll check that tomorrow lube up the post.
- pickerandsinger
- 10+ Years
- Posts: 1501
- Joined: Thu Oct 18, 2012 3:23 pm
- Zip Code: 13143
- Tractors Owned: 1957 Cub Low Boy w/ FH Mott Flail Mower
1953 Cub w/ sprayer and 54A blade (Chompers)
1954 Cub w/fast hitch (Ira)
1948 Cub ( Papa Paul)with Henderson loader..
1951 Mutt mix Cub (BattleAx
1950 Farmall Cub (basket case demo)
Cub parts tractor
2019 " KuB"ota 2601 loader and roto tiller
1951 Ferguson TEA 20 (parts)( Uncle Rusty)
F/H Disc Harrow for cub L-38
C-22 Sickle Bar Mower
IH C2 and C3 mower
Universal tool attachment with disc hillers..Rear cultivators (various tips
York Rake for Cub home made
Single bottom Plow for Cub F194
Gravely 5660 12 hp/ w snoblower.rototiller,bush hog - Circle of Safety: Y
Re: Timing Advance?
Following the post....A moment of learning, thanks to Eugene ........Thanks DaveEugene wrote:Under the rotor, in the center of the post it sits on, is suppose to be a wick. This wick is to be oiled
In Memory of 58,286
-
- 10+ Years
- Posts: 2784
- Joined: Tue Jul 22, 2008 12:44 pm
- Zip Code: 48370
- Tractors Owned: 184
- Location: Oxford, MI
Re: Timing Advance?
Since the tractor is designed to do its work at or near full throttle, you should actually set the timing at full throttle using the 16 degree mark.
It should move toward the 0 degree mark at an idle. If it doesn't make it all the way down to the 0 degree mark then that's ok. Live with it being off a bit at an idle. The tractor is not "doing work" at an idle and will still start very reliably.
It should move toward the 0 degree mark at an idle. If it doesn't make it all the way down to the 0 degree mark then that's ok. Live with it being off a bit at an idle. The tractor is not "doing work" at an idle and will still start very reliably.
184 w/ Creeper & 3-Point
IH 3160a Mower
IH Model 15 Tiller
IH-54 Blade
IH 3160a Mower
IH Model 15 Tiller
IH-54 Blade
-
- Team Cub Mentor
- Posts: 20344
- Joined: Fri Jul 02, 2004 9:52 pm
- Zip Code: 65051
- Circle of Safety: Y
- Location: Mo. Linn
Re: Timing Advance?
At engine cranking speed the ignition system needs to fire at 0 crankshaft degrees, or perhaps a tiny smidgen of a degree later/after. Should the ignition system fire the piston before TDC at engine cranking speed - hard start or no start problems.outdoors4evr wrote:If it doesn't make it all the way down to the 0 degree mark then that's ok. Live with it being off a bit at an idle. The tractor is not "doing work" at an idle and will still start very reliably.
I have an excuse. CRS.
-
- 10+ Years
- Posts: 2784
- Joined: Tue Jul 22, 2008 12:44 pm
- Zip Code: 48370
- Tractors Owned: 184
- Location: Oxford, MI
Re: Timing Advance?
Checked my service manual.
Spark advance @ 400 rpm............0-1 degrees
Spark advance @ 800 rpm............4-8 degrees
Spark advance @ 1200 rpm............10-14 degrees
Spark advance @ 1600 rpm............15-16 degrees
If using a timing light, and verifying the RPM's as you are measuring then timing your engine is easiest (and best) at working RPM's.
I notice it doesn't give a specification for higher RPM's even for the numbered series tractor engines. If you have the 16 degree mark on your front pulley and can set the timing at 1600 rpm's, then the rest usually works out okee dokee. I don't worry about the idle because I may not get my tractor to purr down to 400rpm. Just make sure the timing advance mechanism functions and the timing is being retarded at the lower RPM's.
Spark advance @ 400 rpm............0-1 degrees
Spark advance @ 800 rpm............4-8 degrees
Spark advance @ 1200 rpm............10-14 degrees
Spark advance @ 1600 rpm............15-16 degrees
If using a timing light, and verifying the RPM's as you are measuring then timing your engine is easiest (and best) at working RPM's.
I notice it doesn't give a specification for higher RPM's even for the numbered series tractor engines. If you have the 16 degree mark on your front pulley and can set the timing at 1600 rpm's, then the rest usually works out okee dokee. I don't worry about the idle because I may not get my tractor to purr down to 400rpm. Just make sure the timing advance mechanism functions and the timing is being retarded at the lower RPM's.
184 w/ Creeper & 3-Point
IH 3160a Mower
IH Model 15 Tiller
IH-54 Blade
IH 3160a Mower
IH Model 15 Tiller
IH-54 Blade
-
- 10+ Years
- Posts: 41
- Joined: Tue Jun 16, 2009 5:56 pm
- Zip Code: 02536
- Circle of Safety: Y
Re: Timing Advance?
Thank you for the input. I won't be able to get to it until Monday. I will take all the input and get it straightened out then and report back.
-
- 10+ Years
- Posts: 1421
- Joined: Sun Apr 30, 2006 2:54 pm
- Zip Code: 60073
- Circle of Safety: Y
- Location: IL, Round Lake Heights
Re: Timing Advance?
Eugene wrote:At engine cranking speed the ignition system needs to fire at 0 crankshaft degrees, or perhaps a tiny smidgen of a degree later/after. Should the ignition system fire the piston before TDC at engine cranking speed - hard start or no start problems.
Ditto this remark. I static timed my dist, then put a timing light on it to make sure it was getting proper advance. It was a few degrees short, so I adjusted the dist. That changed the static time, and, as Eugene says, I started having starting problems. Re-did the static time, and she was fine again. Not sure what changed since (probably the fact that I decided to change the points and condenser shortly after and oiled the felt), but she is now advancing properly at high idle.
Lesson learned, make sure the static timing is correct. If you can't get proper advance, then there is something else wrong.
Michael Cummings
Eddie - a 1959 International Lo-Boy named after my father in law, who who bought her new.
Eddie - a 1959 International Lo-Boy named after my father in law, who who bought her new.
- kpaine
- 10+ Years
- Posts: 23
- Joined: Tue Jul 02, 2013 11:19 am
- Zip Code: 39735
- Tractors Owned: 1948 Farmall Cub
1950 Farmall Cub - Location: Ackerman, MS
Re: Timing Advance?
Eugene wrote:Follow Ray's directions to see if the advance is working.
Under the rotor, in the center of the post it sits on, is suppose to be a wick. This wick is to be oiled - and usually not. If advance is not working, set engine on TDC, # 1 cylinder and remove distributor. Set distributor upright in vise or stand. Add quality solvent to the wick. Let set. See if the solvent frees up the advance.
You will only get about an 8 degree movement in the advance, not much more than a wiggle, when it frees up. When free, oil wick and move advance mechanism. Then oil weight and spring pivots.
Not trying to hijack the thread and I am a novice mechanic, but how to you advance #1 to TDC? Pull the spark plug and rotate crank until the piston is at the top of the stroke? Sorry for the dumb question.
Ken
-
- Team Cub Mentor
- Posts: 20344
- Joined: Fri Jul 02, 2004 9:52 pm
- Zip Code: 65051
- Circle of Safety: Y
- Location: Mo. Linn
Re: Timing Advance?
In this instance the engine is capable of running.kpaine wrote:Not trying to hijack the thread and I am a novice mechanic, but how to you advance #1 to TDC? Pull the spark plug and rotate crank until the piston is at the top of the stroke? Sorry for the dumb question. Ken
Remove distributor cap. Rotate engine by hand until the rotor points to the previous #1 spark plug wire location when distributor cap was installed. Check and line up the pointer and TDC mark on pulley by hand.
If engine is not capable of running. Finger in #1 cylinder spark plug hole. Rotate engine until compression felt. Then line up pointer and TDC mark on pulley.
I have an excuse. CRS.
-
- 10+ Years
- Posts: 41
- Joined: Tue Jun 16, 2009 5:56 pm
- Zip Code: 02536
- Circle of Safety: Y
Re: Timing Advance?
To follow up, I static timed my 69 Square Nose. With a timing light, at 1,600 rpm's the pointer is on the bottom pulley mark. At 500 rpm's, it remains on the bottom mark. I have removed the distributor and lubed the wick. I will continue to lube it and spin the distributor manually several times through out today and reinstall it in the morning to see if it frees up the weights.
If not, I guess I will have to disassemble the distributor to free then up???????
Thank you for your help and suggestions.
If not, I guess I will have to disassemble the distributor to free then up???????
Thank you for your help and suggestions.
- John *.?-!.* cub owner
- Cub Pro
- Posts: 23701
- Joined: Sun Feb 02, 2003 2:09 pm
- Zip Code: 63664
- Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
- Location: Mo, Potosi
Re: Timing Advance?
Bob, under the plate the points mount on are weights and springs that cause the advance as it speeds up. The shaft the rotor and points operate with is actually a separate shaft form the one that drives the distributor with one shaft being inside the other. That may be gunked/rusted and need to be cleaned and lubed. with the engine not running you should be able to use your hand to turn the rotor forward and backward a few degrees, with the springs returning it when you release it.
If you are not part of the solution,
you are part of the problem!!!
you are part of the problem!!!
-
- 10+ Years
- Posts: 41
- Joined: Tue Jun 16, 2009 5:56 pm
- Zip Code: 02536
- Circle of Safety: Y
Re: Timing Advance?
Thanks John. I've never had that plate off and was a little concerned that I may screw it up if I went digging in there.
I just went out and held the drive gear and turned the shaft. It was stiff. I lubed it again and worked it several more times. It appears to be freeing up a little. I will continue to lube it and move it for the rest of the day and reinstall it in the morning.
Thank you again.
I just went out and held the drive gear and turned the shaft. It was stiff. I lubed it again and worked it several more times. It appears to be freeing up a little. I will continue to lube it and move it for the rest of the day and reinstall it in the morning.
Thank you again.
Who is online
Users browsing this forum: No registered users and 27 guests