Hi,
D9 Mott flail mower cast iron PTO pulley split. The split goes through the splines inside. I'm not a welder so I'm asking the welders if there is any reasonable repair for this pulley, or has it given up the ghost?
If no repair any ideas as to replacement? JP tractor?
Thanks much,
Todd
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
mott mower pulley repair
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 1224
- Joined: Wed Jul 02, 2008 6:11 am
- Location: MN, Mankato
-
- 10+ Years
- Posts: 5214
- Joined: Tue Jan 12, 2010 2:08 pm
- Zip Code: 12514
- Circle of Safety: Y
Re: mott mower pulley repair
get a new one
-
- 10+ Years
- Posts: 1501
- Joined: Thu Oct 18, 2012 3:23 pm
- Zip Code: 13143
- Tractors Owned: 1957 Cub Low Boy w/ FH Mott Flail Mower
1953 Cub w/ sprayer and 54A blade (Chompers)
1954 Cub w/fast hitch (Ira)
1948 Cub ( Papa Paul)with Henderson loader..
1951 Mutt mix Cub (BattleAx
1950 Farmall Cub (basket case demo)
Cub parts tractor
2019 " KuB"ota 2601 loader and roto tiller
1951 Ferguson TEA 20 (parts)( Uncle Rusty)
F/H Disc Harrow for cub L-38
C-22 Sickle Bar Mower
IH C2 and C3 mower
Universal tool attachment with disc hillers..Rear cultivators (various tips
York Rake for Cub home made
Single bottom Plow for Cub F194
Gravely 5660 12 hp/ w snoblower.rototiller,bush hog - Circle of Safety: Y
Re: mott mower pulley repair
Looks like the 4 inch or 4 1/2 inch pulley also used on a sickle bar mower....If it is, their expensive (over 100.00) on ebay and I haven't located one in New condition....PM me if you find a supplier..Thanks Dave
In Memory of 58,286
-
- 10+ Years
- Posts: 1050
- Joined: Tue Apr 26, 2011 10:47 am
- Zip Code: 44266
- Tractors Owned: 48 F Cub #11678
65 Cub Cadet 104
70 450C JD loader
67 Cub Cadet 107
90 B7100HST-D Kubota
72 Cub Cadet 149
54 Super C - Circle of Safety: Y
- Location: Ravenna, Ohio
Re: mott mower pulley repair
Long story short, you may be able to braze it or use some Normacast welding rod on it. The bigger problem I noticed is the spline grooves look pretty well worn. I've had good luck using the two piece hub and pulley assemblies like those used on a Woods mower set up. They tighten up real nice on the PTO shaft (that may depend on the condition of your PTO shaft), no wiggles or wobbles, and they don't fall down ...er - uh - don't fall off. ...or work loose.
-
- 10+ Years
- Posts: 4565
- Joined: Wed Feb 05, 2003 1:18 pm
- Zip Code: 45365
- Tractors Owned: Home to "Rusty", the 2007 and 2009 Cub Tug Champion.
- Circle of Safety: Y
- Location: OH, Sidney
Re: mott mower pulley repair
TJG wrote:Hi,
D9 Mott flail mower cast iron PTO pulley split. The split goes through the splines inside. I'm not a welder so I'm asking the welders if there is any reasonable repair for this pulley, or has it given up the ghost?
If no repair any ideas as to replacement? JP tractor?
Thanks much,
Todd
Todd, what is the diameter? I have one hanging on the wall that came to me on my '61 Lo-Boy.
-
- Cub Pro
- Posts: 23701
- Joined: Sun Feb 02, 2003 2:09 pm
- Zip Code: 63664
- Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
- Location: Mo, Potosi
Re: mott mower pulley repair
They can be welded by someone that knows what they are doing, I have been using a welded one for over a year. As was mentioned however the splines on yours are badly worn,it appears that it has been run without being clamped tight enough. continuing to run it that way will wear the splines on the pto shaft if it has not already done so.
Those are 8 inch pulleys, and hard to find. that particular pulley has not been manufactured in several years. An 8 inch Woods pulley for a 42 inch mower will work, but if you have the later idler pulleys that bolt to the curve in the drawbar the belt actually lines up just past the end of the pto shaft, so to get the split hub Woods pulley to line up properly you need to install the pulley with the bolts turned toward the transmission.
Those are 8 inch pulleys, and hard to find. that particular pulley has not been manufactured in several years. An 8 inch Woods pulley for a 42 inch mower will work, but if you have the later idler pulleys that bolt to the curve in the drawbar the belt actually lines up just past the end of the pto shaft, so to get the split hub Woods pulley to line up properly you need to install the pulley with the bolts turned toward the transmission.
If you are not part of the solution,
you are part of the problem!!!
you are part of the problem!!!
-
- 10+ Years
- Posts: 1224
- Joined: Wed Jul 02, 2008 6:11 am
- Location: MN, Mankato
Re: mott mower pulley repair
John, this is the attachment that I have. Are you saying I'd have to move the idler bracket towards the center of the drawbar?
How does the Woods pulley clamp tightly to the PTO shaft? I've looked a pictures on Hamiltonbobs and I don't see how they tighten, unless I'm looking at the wrong pulley.
Todd
-
- 10+ Years
- Posts: 1501
- Joined: Thu Oct 18, 2012 3:23 pm
- Zip Code: 13143
- Tractors Owned: 1957 Cub Low Boy w/ FH Mott Flail Mower
1953 Cub w/ sprayer and 54A blade (Chompers)
1954 Cub w/fast hitch (Ira)
1948 Cub ( Papa Paul)with Henderson loader..
1951 Mutt mix Cub (BattleAx
1950 Farmall Cub (basket case demo)
Cub parts tractor
2019 " KuB"ota 2601 loader and roto tiller
1951 Ferguson TEA 20 (parts)( Uncle Rusty)
F/H Disc Harrow for cub L-38
C-22 Sickle Bar Mower
IH C2 and C3 mower
Universal tool attachment with disc hillers..Rear cultivators (various tips
York Rake for Cub home made
Single bottom Plow for Cub F194
Gravely 5660 12 hp/ w snoblower.rototiller,bush hog - Circle of Safety: Y
-
- Cub Pro
- Posts: 23701
- Joined: Sun Feb 02, 2003 2:09 pm
- Zip Code: 63664
- Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
- Location: Mo, Potosi
Re: mott mower pulley repair
the woods pulley is made in 2 pieces, it has a tapered center hub that fits the splines, and the outer pulley slides over it. there are 2 or 3 bolts (depending on which pulley) that pull the 2 pieces together locking it in place and clamping to the shaft. Normally it is installed with the bolts to the rear where they are easy to get to, but to get the pulley far enough back to line up with the idlers and still have a good grip on the pto shaft it has to be turned around with the bolts to the front unless you can come up with a way of moving the idler pulleys toward the front of the mower.
If you are not part of the solution,
you are part of the problem!!!
you are part of the problem!!!
-
- Team Cub Mentor
- Posts: 20378
- Joined: Fri Jul 02, 2004 9:52 pm
- Zip Code: 65051
- Circle of Safety: Y
- Location: Mo. Linn
Re: mott mower pulley repair
The idler bracket is correctly installed.TJG wrote:Are you saying I'd have to move the idler bracket towards the center of the drawbar?
I have an excuse. CRS.
-
- 10+ Years
- Posts: 1050
- Joined: Tue Apr 26, 2011 10:47 am
- Zip Code: 44266
- Tractors Owned: 48 F Cub #11678
65 Cub Cadet 104
70 450C JD loader
67 Cub Cadet 107
90 B7100HST-D Kubota
72 Cub Cadet 149
54 Super C - Circle of Safety: Y
- Location: Ravenna, Ohio
Re: mott mower pulley repair
John *.?-!.* cub owner wrote:to get the split hub Woods pulley to line up properly you need to install the pulley with the bolts turned toward the transmission.
In other words, it goes on backwards compared to the normal installation. That will work if you need to do that to align the belt as long as the pulley hub tightens up enough. If your PTO shaft is worn too much it may not. I did pretty much the same thing for a Cub 22 sickle bar pulley and it would not stay on the shaft but installed with the bolts facing back (normal installation) it stayed on with no problem but belt alignment was an issue.
-
- Similar Topics
- Replies
- Views
- Last post
-
- 6
- 170
-
by Don McCombs
Wed Mar 27, 2024 3:43 pm
-
- 1
- 179
-
by Dale Finch
Thu Jun 09, 2022 10:33 pm
-
- 1
- 234
-
by Jim Becker
Mon Aug 09, 2021 1:16 pm
-
- 28
- 983
-
by SamsFarm
Wed Jul 28, 2021 11:19 pm
-
-
Mott Flail Mower Fast Hitch Question Attachment(s)
by darkmuncan81 » Tue Oct 25, 2022 1:35 pm » in Farmall Cub - 7
- 254
-
by Don McCombs
Thu Oct 27, 2022 3:59 pm
-
Who is online
Users browsing this forum: Majestic-12 [Bot] and 10 guests