This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
International 54A Blade
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
- jlmason81
- 10+ Years
- Posts: 132
- Joined: Thu Nov 18, 2010 8:43 pm
- Zip Code: 75126
- eBay ID: jlmason81
- Location: Forney, Texas
International 54A Blade
I just recently purchased this original paint blade and wanted to make sure I mounted it correctly. Is there suppose to be a flat washer used in the mounting of the 12" bolt? Does it act as a spacer for the lift arm to keep it from hitting the steering housing? How long is the bushing in the lift arm suppose to be? Please critique so I may get it mounted correctly. Thanks.
Jeff
Jeff
- Attachments
-
- photo 2.JPG (134.74 KiB) Viewed 969 times
-
- photo 3.JPG (139.97 KiB) Viewed 969 times
-
- photo 1.JPG (149.96 KiB) Viewed 969 times
-
- photo 4.JPG (139.04 KiB) Viewed 969 times
-
- Team Cub
- Posts: 11851
- Joined: Tue May 25, 2004 8:02 pm
- Zip Code: 80501
- Tractors Owned: Cubs, MH Pony, Shaw, Allis G, 1934 Silver King, JD LA and LI, Gibson D, David Bradley Tri-Trac
- Circle of Safety: Y
- Location: CO, Longmont
Re: International 54A Blade
Jeff, Neither the assembly section of the manual or the parts manual show a washer used as a spacer. Mine has never rubbed there. I would guess that you have a slight bend or wear somewhere that allows the rubbing on the steering box. That being said, I see no reason not to use a washer. I can't give you a length on the bushing, but the ones I have made extend out both sides of the lift arms about 1/16-1/8" to prevent binding when the the 12" bolt is tightened. I use black gas line to make those and it has worked well (you may have to file down the seam on the inside to allow the bolt to slide through it. We may get some snow tonight, want to come up and try it out?
Bob
Bob
"We don't need to think more,
we need to think differently."
-Albert Einstein
we need to think differently."
-Albert Einstein
- jlmason81
- 10+ Years
- Posts: 132
- Joined: Thu Nov 18, 2010 8:43 pm
- Zip Code: 75126
- eBay ID: jlmason81
- Location: Forney, Texas
Re: International 54A Blade
Bob,
Thank you for the info. I also used black pipe to make my bushing. Lucky enough it didnt have a weld seam on the inside of the pipe. The arm isn't rubbing yet but it is "very" close! The lifting arm is turning a toward the inside which makes it closer to the steering housing. The black pipe probably allows 1/16" of play. What is the normal distance between the lifting arm and the steering housing? I did go to the Case IH dealer up the street and they show that the bushing is no longer available.
Jeff
Thank you for the info. I also used black pipe to make my bushing. Lucky enough it didnt have a weld seam on the inside of the pipe. The arm isn't rubbing yet but it is "very" close! The lifting arm is turning a toward the inside which makes it closer to the steering housing. The black pipe probably allows 1/16" of play. What is the normal distance between the lifting arm and the steering housing? I did go to the Case IH dealer up the street and they show that the bushing is no longer available.
Jeff
- bob in CT
- Team Cub Mentor
- Posts: 6018
- Joined: Thu Jun 07, 2007 9:34 am
- Zip Code: 06040
- Tractors Owned: 77 Cub (red); 74 Cub; 52 Cub; 50 Cub ( post-demo)
- Circle of Safety: Y
- Location: CT, Manchester
Re: International 54A Blade
What are you using to lock down the square blocks in the housing? Should be 5/8-11 cup set screws. Bolts just need to mushroom a little bit and they are a bear to remove.
- randallc
- Cub Pro
- Posts: 1906
- Joined: Tue Jan 18, 2011 9:16 am
- Zip Code: 72940
- Tractors Owned: 1951 Farmall Cub, 152 disk plow, 2 gang disk, belly mower, sickle mower
1949 Farmall Cub, cultivator, moldboard plow, disk,front blade. Cub Cadet, LTX1045 Mower. Cub Cadet's 109, 125, 1000, and 1250
1961 cub c2 belly mower and full blade. 48 cub manual lift with cultivators.
1947 Cub - Circle of Safety: Y
- Location: Huntington, AR
Re: International 54A Blade
Jeff, I never have measured my blade as far as the nearest to the steering housing, but it is very close.
Good looking originals you have collected.
Good looking originals you have collected.
- jlmason81
- 10+ Years
- Posts: 132
- Joined: Thu Nov 18, 2010 8:43 pm
- Zip Code: 75126
- eBay ID: jlmason81
- Location: Forney, Texas
Re: International 54A Blade
Bob, very good point. I need to check! I do know I removed them from an original 1973 Cub from the same location. They have IH stamped on the head, but I didn't verify if they were a cup bolt. I will check tomorrow.
Randall,
Thank you. All I am interested in now is nice original cubs. Clean Originals.. The other side of my garage has the red early models. They are lined up by year.
Jeff
Randall,
Thank you. All I am interested in now is nice original cubs. Clean Originals.. The other side of my garage has the red early models. They are lined up by year.
Jeff
- LeeC
- 10+ Years
- Posts: 343
- Joined: Fri Oct 31, 2008 2:07 pm
- Zip Code: 22150
- Tractors Owned: 2 1962 LoBoys
1 1964 LoBoy
1 1965 LoBoy
1 1966 LoBoy - Circle of Safety: Y
- Location: Springfield, VA
Re: International 54A Blade
Although the parts manual shows heat treated hex head machine bolts, Bob is right about what is best.
-
- Team Cub
- Posts: 17272
- Joined: Sun Feb 02, 2003 2:59 pm
- Zip Code: 55319
- Circle of Safety: Y
- Location: MN
Re: International 54A Blade
The parts breakdown doesn't show a flat washer on the long bolt. I had one where the lift arm was against the steering gear. So I added a flat washer on the left side of the arm and it tightened it up enough to keep the arm from rubbing. I don't remember what sort of washer I used. Maybe it was a 5/8, or it could have been a 1/2 fender washer that might have needed drilling out a bit. What works and how well may depend on the particular blade and how much wear it has.
Also make sure the 12" bolt isn't bent. A little bend on the right end will allow the lift arm to get askew. Inserting the bolt from right to left, so the arm is not on the threaded part, may help as well.
In most cases, the hex head machine bolts were supplied by IH for the square implement mounting socket. The Cub-22 mower came with a set screw. As we know, the mower was hard to keep tight. It definitely needed the set screw and it is a good idea to use it with any implement.
Also make sure the 12" bolt isn't bent. A little bend on the right end will allow the lift arm to get askew. Inserting the bolt from right to left, so the arm is not on the threaded part, may help as well.
In most cases, the hex head machine bolts were supplied by IH for the square implement mounting socket. The Cub-22 mower came with a set screw. As we know, the mower was hard to keep tight. It definitely needed the set screw and it is a good idea to use it with any implement.
- jlmason81
- 10+ Years
- Posts: 132
- Joined: Thu Nov 18, 2010 8:43 pm
- Zip Code: 75126
- eBay ID: jlmason81
- Location: Forney, Texas
Re: International 54A Blade
Thank you for the info Jim! The 12" bolt was just purchased this week from Case IH so it was nice and straight. I think my issue may be that the lift arm is bent in on the flat bar side (right side from sitting on the seat of the tractor) where someone over tightened the bolt. Between that and the 1/16" of play in my home made bushing that may be the issue. The arm isn't rubbing yet but it may be a 1/8" from the steering gear. Is that about the norm?
Jeff
Jeff
-
- Team Cub
- Posts: 17272
- Joined: Sun Feb 02, 2003 2:59 pm
- Zip Code: 55319
- Circle of Safety: Y
- Location: MN
Re: International 54A Blade
There may have been a little more clearance than that when they were new (certainly not much more). But if you can get one mounted and run through the range of motion without actually rubbing, you have done well.
- jlmason81
- 10+ Years
- Posts: 132
- Joined: Thu Nov 18, 2010 8:43 pm
- Zip Code: 75126
- eBay ID: jlmason81
- Location: Forney, Texas
Re: International 54A Blade
Thanks Jim.
I think I will straighten the lift arm a little more and let it be. I have the bushing maybe a total of 1/16 or so longer than the arm so that there is no rubbing, so I should be good. I got this blade from a good friend Sam Adams. Have you ever been to his place in Tatum? I took my dad out there last Saturday and he could not believe it. Its definitely a trip you have to take. I have been talking to him about hosting a Cub Fest at his place too.
Jeff
I think I will straighten the lift arm a little more and let it be. I have the bushing maybe a total of 1/16 or so longer than the arm so that there is no rubbing, so I should be good. I got this blade from a good friend Sam Adams. Have you ever been to his place in Tatum? I took my dad out there last Saturday and he could not believe it. Its definitely a trip you have to take. I have been talking to him about hosting a Cub Fest at his place too.
Jeff
-
- Team Cub
- Posts: 17272
- Joined: Sun Feb 02, 2003 2:59 pm
- Zip Code: 55319
- Circle of Safety: Y
- Location: MN
Re: International 54A Blade
I've been to Sam's, gotten a couple things from him.
- pickerandsinger
- 10+ Years
- Posts: 1501
- Joined: Thu Oct 18, 2012 3:23 pm
- Zip Code: 13143
- Tractors Owned: 1957 Cub Low Boy w/ FH Mott Flail Mower
1953 Cub w/ sprayer and 54A blade (Chompers)
1954 Cub w/fast hitch (Ira)
1948 Cub ( Papa Paul)with Henderson loader..
1951 Mutt mix Cub (BattleAx
1950 Farmall Cub (basket case demo)
Cub parts tractor
2019 " KuB"ota 2601 loader and roto tiller
1951 Ferguson TEA 20 (parts)( Uncle Rusty)
F/H Disc Harrow for cub L-38
C-22 Sickle Bar Mower
IH C2 and C3 mower
Universal tool attachment with disc hillers..Rear cultivators (various tips
York Rake for Cub home made
Single bottom Plow for Cub F194
Gravely 5660 12 hp/ w snoblower.rototiller,bush hog - Circle of Safety: Y
Re: International 54A Blade
Anyone happen to know the distance between the holes on Part number one in the manual drawing....I understand the spacing for the implement holes but its the lower hole, say from the upper hole center to the lower hole center I need....Maybe the thickness of the material used also....Many thanks... Dave
In Memory of 58,286
- Bill V in Md
- 10+ Years
- Posts: 1124
- Joined: Sun Feb 02, 2003 6:51 pm
- Zip Code: 21228
- Tractors Owned: 1948 Farmall Cub
LT1045 Cub Cadet - Circle of Safety: Y
- Location: MD, Catonsville
- Contact:
Re: International 54A Blade
pickerandsinger wrote:Anyone happen to know the distance between the holes on Part number one in the manual drawing....I understand the spacing for the implement holes but its the lower hole, say from the upper hole center to the lower hole center I need....Maybe the thickness of the material used also....Many thanks... Dave
Dave, I measured mine and it is 1/2" thick. The holes on each end are 6 3/4" center-to-center.
Bill VanHooser
Cub 54 Blade, Cub 193 Moldboard Plow, Cub 28A Disc Harrow
Cub 54 Blade, Cub 193 Moldboard Plow, Cub 28A Disc Harrow
- pickerandsinger
- 10+ Years
- Posts: 1501
- Joined: Thu Oct 18, 2012 3:23 pm
- Zip Code: 13143
- Tractors Owned: 1957 Cub Low Boy w/ FH Mott Flail Mower
1953 Cub w/ sprayer and 54A blade (Chompers)
1954 Cub w/fast hitch (Ira)
1948 Cub ( Papa Paul)with Henderson loader..
1951 Mutt mix Cub (BattleAx
1950 Farmall Cub (basket case demo)
Cub parts tractor
2019 " KuB"ota 2601 loader and roto tiller
1951 Ferguson TEA 20 (parts)( Uncle Rusty)
F/H Disc Harrow for cub L-38
C-22 Sickle Bar Mower
IH C2 and C3 mower
Universal tool attachment with disc hillers..Rear cultivators (various tips
York Rake for Cub home made
Single bottom Plow for Cub F194
Gravely 5660 12 hp/ w snoblower.rototiller,bush hog - Circle of Safety: Y
Who is online
Users browsing this forum: tucker86 and 48 guests