Keep in mind as you're making your hitch that once you get plowing your right wheels will (should) be in the furrow you plowed on the previous pass. That will make the right side set lower than the left wheels by what ever depth you plow. If you mount the plow level on flat ground you'll be plowing a sawtooth pattern under your turned soil. There is a twist in the Cub plows beam so the plow sets level when it's working. If you mount the plow in the center of the tractor and then move over 12" (or whatever width your plow is) to the left to do your next furrow, your right wheels will be packing down the dirt you just turned if the right back wheel gets any traction at all. It should be mounted the width of the plow just inside the right rear wheel. You'll still need some sort of depth control as has been mentioned, as well as I'm not so sure "loosely mounted to the drawbar" is the best option. The Cub plow is fairly rigid with springs to cushion if you hit something. I don't know how well a plow will track on it's own it it can swing left and right. When it swings a little either direction off center, it's going to be a lot harder to pull. Taking it to extremes for illustration the more it swings to the right the more it becomes a grader blade instead of a plow.
It all can be done, but it's going to take a lot of patientence and persistence.
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Bottom Plow
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 2929
- Joined: Sun Apr 19, 2009 9:51 pm
- Zip Code: 63664
- Location: MO, Potosi
-
- 10+ Years
- Posts: 4113
- Joined: Thu Nov 09, 2006 11:26 pm
- Zip Code: 61722
Re: Bottom Plow
The lift is going to be hard to invent,--BUT possible to do. Make up a sleeve hitch that will fit the cub and hang the same height as if on garden tractor,--OR make a 3-point adapter and use the plow as a 3pt mount,---I use a 10" Brinley bottom on 1 of my cubs( modified as 3-pt hitch) and one on my AC 918 sleeve hitch tractor. Both work well but getting them set right is a bear! good luck on the idea! thanks; sonny
-
- 10+ Years
- Posts: 77
- Joined: Thu Apr 26, 2012 12:08 pm
- Zip Code: 42378
- Tractors Owned: 48 Farmall Cub, 55 Farmall 100, 35 10-20 mc cormick
- Circle of Safety: Y
Re: Bottom Plow
I've used an old Brinley plow mounted to the far right of the drawbar for several years. The draw bar floating and a chain lift to the rear rock shaft. You want the plow level about 4 to 6 inches deep. The hardest thing is adjusting the cant (or tilt) to lay over the sod, if you're on uneven ground laying over downhill always helps, plus it's a basic safety rule "engine uphill".
Dale
"It's better to regret the things you've done than the things you didn't do."
Still can't help to think "Wish I hadn't of done that!"
"It's better to regret the things you've done than the things you didn't do."
Still can't help to think "Wish I hadn't of done that!"
-
- 10+ Years
- Posts: 133
- Joined: Fri Sep 02, 2011 6:22 pm
- Zip Code: 33876
Re: Bottom Plow
I'm just goin to throw this out ,admitting that I don't have a Cub with or without a plow.
1)The Brinly Hardy instuctions on mounting their plow on a Cub Cadet say to let the plow "swing" within the small radius
that it can. 2) If you consider the first plows, pulled by horses, they were not "mounted" and when properly adjusted with a good point would "draft" and plow a good furrow with the ploughman mostly keeping the plow from falling on it's side.
But with a plow "mounted" by whatever means, the tire in the previously plowed furrow makes it neccesary to have the beam turned, rwisted, canted what ever, in relation to the depth the tire is running in the furrow. Buttt, as to Cubs and Cub plows, I say whatever Bill Hudson says is correct.
1)The Brinly Hardy instuctions on mounting their plow on a Cub Cadet say to let the plow "swing" within the small radius
that it can. 2) If you consider the first plows, pulled by horses, they were not "mounted" and when properly adjusted with a good point would "draft" and plow a good furrow with the ploughman mostly keeping the plow from falling on it's side.
But with a plow "mounted" by whatever means, the tire in the previously plowed furrow makes it neccesary to have the beam turned, rwisted, canted what ever, in relation to the depth the tire is running in the furrow. Buttt, as to Cubs and Cub plows, I say whatever Bill Hudson says is correct.
-
- 10+ Years
- Posts: 12
- Joined: Wed May 20, 2009 1:17 am
- Zip Code: 85242
- Tractors Owned: 1948 Farmall Cub
- Location: Queen Creek, Arizona
Re: Bottom Plow
Thanks for your help. I know you don't plow in circles, but I figured it wouldn't hurt since it only went in about 3 inches. Next question. The end of the plow where it attaches to the tractor is at an angle. Do I mount it so that angle is kept or do I mount it straight horizontal like the draw bar? In other words do I keep the plow vertical or the mount horizontal?
Boy you guys are good. I didn't notice there was a second page when I wrote this question. How did you know I was going to ask this? Please ignore.
Boy you guys are good. I didn't notice there was a second page when I wrote this question. How did you know I was going to ask this? Please ignore.
'48 Farmall Cub
-
- 10+ Years
- Posts: 1174
- Joined: Thu Jun 10, 2010 6:56 am
- Zip Code: 49053
- Circle of Safety: Y
- Location: Galesburg, MI
Re: Bottom Plow
Bill68 wrote:Thanks for your help. I know you don't plow in circles, but I figured it wouldn't hurt since it only went in about 3 inches. Next question. The end of the plow where it attaches to the tractor is at an angle. Do I mount it so that angle is kept or do I mount it straight horizontal like the draw bar? In other words do I keep the plow vertical or the mount horizontal?
Boy you guys are good. I didn't notice there was a second page when I wrote this question. How did you know I was going to ask this? Please ignore.
You can if you wish and no one has posted a reply go in and delete as an edit. You can also at any time strike out the text as an edit which shows only that at sometime you posted. But you are far from the first one who changes their mind. Vern
-
- 10+ Years
- Posts: 2791
- Joined: Tue Jul 22, 2008 12:44 pm
- Zip Code: 48370
- Tractors Owned: 184
- Location: Oxford, MI
Re: Bottom Plow
Since the plow hasn't been adapted to the tractor yet, try this.
If your tires width is set to a wide setting, you might need to set it to a more narrow setting on the non-engine side so that the drawbar holes are closer to the tire.
Set the front tire width to match the rear.
Park the tractor on a flat surface. Jack up the rear (engine side) tire approximately 6-8" and put blocks under the tire to make up the height. Lock brakes & block the tires. Remove jack.
Measure the width of the plow. The plow should be mounted so that the plow tip is at 2x the width measured from the inside of the rear tire.
Adjust the angle of the plow (or create a custom mount) so that the cutting edge of the plow is perpendicular to the ground (at a right angle). Use a square as a guide.
Construct your lifting mechanism for the plow. The plow will be approximately 2" below its current plane when plowing and the lift mechanism must lift high enough to clear the ground amply when the 4 tires are on level ground.
If the plow doesn't want to dig into the ground, then further lower the mounting point. Worn out plow tips also do not help this.
OR...........
Get a rototiller. That's what I did.
If your tires width is set to a wide setting, you might need to set it to a more narrow setting on the non-engine side so that the drawbar holes are closer to the tire.
Set the front tire width to match the rear.
Park the tractor on a flat surface. Jack up the rear (engine side) tire approximately 6-8" and put blocks under the tire to make up the height. Lock brakes & block the tires. Remove jack.
Measure the width of the plow. The plow should be mounted so that the plow tip is at 2x the width measured from the inside of the rear tire.
Adjust the angle of the plow (or create a custom mount) so that the cutting edge of the plow is perpendicular to the ground (at a right angle). Use a square as a guide.
Construct your lifting mechanism for the plow. The plow will be approximately 2" below its current plane when plowing and the lift mechanism must lift high enough to clear the ground amply when the 4 tires are on level ground.
If the plow doesn't want to dig into the ground, then further lower the mounting point. Worn out plow tips also do not help this.
OR...........
Get a rototiller. That's what I did.
184 w/ Creeper & 3-Point
IH 3160a Mower
IH Model 15 Tiller
IH-54 Blade
IH 3160a Mower
IH Model 15 Tiller
IH-54 Blade
-
- 10+ Years
- Posts: 4113
- Joined: Thu Nov 09, 2006 11:26 pm
- Zip Code: 61722
Re: Bottom Plow
Rototiller is best option!LOL! ---Got my King Kutter 72" on the 3-pt of my Harley-Davidson tractor and tills like mad! LOL! 1 pass --8" deep and ready to plant! thanks; sonny
-
- 10+ Years
- Posts: 12
- Joined: Wed May 20, 2009 1:17 am
- Zip Code: 85242
- Tractors Owned: 1948 Farmall Cub
- Location: Queen Creek, Arizona
Re: Bottom Plow
Finally got my Nexus tablet working. Here are a few pictures of the plow and blade plus details of how they are mounted. Also included are the winches that power everything.
- Attachments
-
- Winch powered plow and blade mount
- Rear Winch, Plow Mount and Blade Mount.png (506.61 KiB) Viewed 514 times
-
- Details of blade mount.
- Blade Mount.png (510.53 KiB) Viewed 514 times
-
- Winch powered 6' blade
- Side Winch, Blade and Blade Mount.png (509.74 KiB) Viewed 514 times
-
- Plow Angle as mounted.
- Angle When Touching Ground.png (511.41 KiB) Viewed 514 times
-
- Picture of the plow
- Plow.png (508.87 KiB) Viewed 514 times
'48 Farmall Cub
-
- 10+ Years
- Posts: 2929
- Joined: Sun Apr 19, 2009 9:51 pm
- Zip Code: 63664
- Location: MO, Potosi
Re: Bottom Plow
There's gonna be a lot of surprised people when they see your plow! That ain't what they were thinking it was. Have you got to try it yet? Go in the ground more than before?
-
- 10+ Years
- Posts: 12
- Joined: Wed May 20, 2009 1:17 am
- Zip Code: 85242
- Tractors Owned: 1948 Farmall Cub
- Location: Queen Creek, Arizona
Re: Bottom Plow
The tractor has no hydraulics and probably never had a blade before. I bought it at a relative's estate sale for a fair price and started thinking about what I could do with it. At first I just dragged things around and then we found that blade in Colorado for a good price. Had to make adapters for it to mount on the front of the rear wheel structure. I already had mounted a winch on the back for lifting rear implements. Found a thick piece of plate steel and fashioned one for the side to lift the blade. I've used cheap Harbor Freight winches. It works real well unless I let it dig in too deep. Then I end up with spinning tires, even with the wheel weights. I use it mainly for weed control, Leveling, clearing a right of way for a fence, and ploughing under horse manure. I'd like to have a cheap fence post hole digger attachment.
Sorry, I thought you were asking about the blade. Duh. So far I haven't gotten the plow to go in more than about 5 or 6 inches. I think there is enough angle adjustment for where I have it mounted. The height at the beginning of the throw is around 10" and I had hoped it would go in that deep. I'll keep playing with it. All suggestions are welcomed.
Sorry, I thought you were asking about the blade. Duh. So far I haven't gotten the plow to go in more than about 5 or 6 inches. I think there is enough angle adjustment for where I have it mounted. The height at the beginning of the throw is around 10" and I had hoped it would go in that deep. I'll keep playing with it. All suggestions are welcomed.
'48 Farmall Cub
-
- 10+ Years
- Posts: 12
- Joined: Wed May 20, 2009 1:17 am
- Zip Code: 85242
- Tractors Owned: 1948 Farmall Cub
- Location: Queen Creek, Arizona
Re: Bottom Plow
I figured out the drawbar swivels both in forward and backward positions. I mounted the plow directly to the drawbar and it plows pretty deep in soft ground. When I pass over hard ground it barely makes a scratch. Somewhere I heard about drawbars swiveling but I can't remember where.
Thanks again for your help!
Thanks again for your help!
'48 Farmall Cub
-
- Similar Topics
- Replies
- Views
- Last post
-
- 3
- 455
-
by CharlieK
Thu Mar 24, 2022 6:32 pm
-
- 4
- 180
-
by NJ Farmer
Mon Jun 12, 2023 10:00 am
-
-
Cub 193 with Canadian Ace bottom Attachment(s)
by Stevetractor » Sat Nov 19, 2022 9:29 am » in Farmall Cub - 6
- 286
-
by Stevetractor
Sun Nov 20, 2022 10:14 am
-
-
- 2
- 185
-
by masseycreek
Thu Jul 01, 2021 12:19 pm
-
-
Replacing bottom gasket on touch control cylinder block Attachment(s)
by Gene Rogers » Mon Feb 07, 2022 11:35 am » in Farmall Cub - 5
- 338
-
by Ken (48 Cub)
Tue Feb 08, 2022 9:14 am
-
Who is online
Users browsing this forum: ghanlin and 3 guests