More starting problems

Farmall H, HV & Super H, 300 & 350, 1939-1958
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
User avatar
Jim in SC
5+ Years
5+ Years
Posts: 355
Joined: Mon Sep 15, 2014 10:16 am
Zip Code: 29527
Tractors Owned: 1951 Farmall H - "Ray R." (SN FBH 366519)
1959 Farmall Cub - "Pea" (SN 211538 J)
1964 IH Cub Cadet 100 - (SN 92562)
1971 IH Cub Cadet 106 - (SN 380760)

2018 Husqvarna YTH18542

Tractor previously owned:
1951 Farmall Cub - "Johnny R."
Circle of Safety: Y
Location: Conway, South Carolina

More starting problems

Postby Jim in SC » Sat Apr 20, 2019 2:43 pm

I just read pokitisme's post. Mine is similar, but I sureI need a little help.

I've owned my Farmall H for a little over a year. It was running okay when I got it and it ran until last September. With winter coming on I decided to do some work on it. I rebuilt the carb, replaced all the wiring, including the battery cables (O gauge wire), put in a new ignition switch, changed the plugs (gapped at 0.23"), replaced the plug wires, installed new points (gapped at 0.20") and condenser, and put in new water temperature and ammeter gauges, The ammeter shows discharge when the lights are turned on. The tractor has a 6 volt system with a good, year old battery. Since doing the work I've mentioned, I've tried starting it, but all it does is turn over, flood the carb, and backfire. I've double checked the timing by pulling the plug on the #1 cylinder and am getting a spark at TDC. I tried putting the old condenser in and re-gapped the points. The engine has good compression and is blowing air out from the exhaust mainifold and sucking air in at the carb, but it won' fire. When I stop cranking the engine, I get fuel gushing out the air intake on the carb.

Nothing has helped.

What am I missing? Any suggestions? I guess I could try putting the old points back in. If that doesn't work, I should I pull the carb and check it out again? :help:
Circle of Safety
"That's the great thing about a tractor. You can't really hear the phone ring."
Jeff Foxworthy

1951 Farmall H
1959 Farmall Cub
1964 IH Cub Cadet 100
1971 IH Cub Cadet 106
2018 Husqvarna YTH18542

User avatar
Dale Finch
10+ Years
10+ Years
Posts: 5636
Joined: Tue Apr 27, 2010 11:34 am
Zip Code: 27517
Tractors Owned: '51 Cub "Bernie" with Fast Hitch
'55 Cub "Bruno" with Woods 59 mower
'55 Cub "Bertha" with Woods 42 mower
'55 Cub "Ben" with Woods 42 mower
'56 Cub "Boris" with Mott Flail mower
Circle of Safety: Y
Location: NC, Chapel Hill

Re: More starting problems

Postby Dale Finch » Sat Apr 20, 2019 3:55 pm

Did you double check the plug wires to MAKE SURE they are in the right order. I think we've all goofed on that at least once.
Dale Finch
Image
Circle of Safety

User avatar
Slim140
501 Club
501 Club
Posts: 4698
Joined: Wed Nov 22, 2017 6:24 am
Zip Code: 00000
Tractors Owned: .
1970 International 140
1972 International 140
1949 John Deere A
1993 Ford 4630 W/Loader
1965 John Deere 110
1961 Cub Cadet Original
Circle of Safety: Y

Re: More starting problems

Postby Slim140 » Sat Apr 20, 2019 4:15 pm

Dale Finch wrote:Did you double check the plug wires to MAKE SURE they are in the right order. I think we've all goofed on that at least once.

Yes, a Cub will run on 2 cylinders, don’t ask how I know :roll:
Every home is a school, what are you teaching?

Circle of Safety

ajhbike
501 Club
501 Club
Posts: 1288
Joined: Thu Mar 09, 2017 4:06 pm
Zip Code: 06405
Tractors Owned: 1957 Cub
1950 Cub
1951 Super C
1966 IH 504 Hi-Clear
1968 JD 3020
1949 Ferguson TO-20
1955 Ferguson TO-35
Location: Branford, CT

Re: More starting problems

Postby ajhbike » Sat Apr 20, 2019 6:56 pm

Maybe carb not put together right so you get the gushing?. 100% Dale is right, that firing order will get ya too (or getting compression and exhaust mixed up for TDC)

User avatar
Jim in SC
5+ Years
5+ Years
Posts: 355
Joined: Mon Sep 15, 2014 10:16 am
Zip Code: 29527
Tractors Owned: 1951 Farmall H - "Ray R." (SN FBH 366519)
1959 Farmall Cub - "Pea" (SN 211538 J)
1964 IH Cub Cadet 100 - (SN 92562)
1971 IH Cub Cadet 106 - (SN 380760)

2018 Husqvarna YTH18542

Tractor previously owned:
1951 Farmall Cub - "Johnny R."
Circle of Safety: Y
Location: Conway, South Carolina

Re: More starting problems

Postby Jim in SC » Sun Apr 21, 2019 6:01 am

Okay, I'll double check on the plug wires in the morning. Maybe go with the old wires that I have laying around somewhere, just to make sure. That's a good comment on the carb, but Ill try the wires first, hopefully it'll do the trick and I won't have to mess with the carb again! I'll post again when I give the wires a try. Thanks to all!
Circle of Safety
"That's the great thing about a tractor. You can't really hear the phone ring."
Jeff Foxworthy

1951 Farmall H
1959 Farmall Cub
1964 IH Cub Cadet 100
1971 IH Cub Cadet 106
2018 Husqvarna YTH18542

User avatar
Jim in SC
5+ Years
5+ Years
Posts: 355
Joined: Mon Sep 15, 2014 10:16 am
Zip Code: 29527
Tractors Owned: 1951 Farmall H - "Ray R." (SN FBH 366519)
1959 Farmall Cub - "Pea" (SN 211538 J)
1964 IH Cub Cadet 100 - (SN 92562)
1971 IH Cub Cadet 106 - (SN 380760)

2018 Husqvarna YTH18542

Tractor previously owned:
1951 Farmall Cub - "Johnny R."
Circle of Safety: Y
Location: Conway, South Carolina

Re: More starting problems

Postby Jim in SC » Mon Apr 22, 2019 1:52 pm

Dang. I changed out the plug wires and the points. Checked to make sure the distributor cap was on right. Nothing. Same problem. I guess next is to take the dang carb off and see what's up with it. Could it be the coil?
Circle of Safety
"That's the great thing about a tractor. You can't really hear the phone ring."
Jeff Foxworthy

1951 Farmall H
1959 Farmall Cub
1964 IH Cub Cadet 100
1971 IH Cub Cadet 106
2018 Husqvarna YTH18542

User avatar
ShawnAgne
5+ Years
5+ Years
Posts: 728
Joined: Sat May 07, 2016 5:13 pm
Zip Code: 45380
Tractors Owned: 1952 Cub w/ 184 motor (Kid)
12V with Petronix
IH 3160 Mower Deck
54 Leveling Blade
193 Plow
IH528 Trailer
Front/Rear Weights
1955 Farmall 300 (Clarence)
12V with Petronix
Woods L306 72"
1955 Farmall 100 (Thomas)
Woods L59 60"
A60 Leveling Blade
Circle of Safety: Y
Location: Versailles, Ohio

Re: More starting problems

Postby ShawnAgne » Mon Apr 22, 2019 7:01 pm

Do you have a check light? I'd trace to see if you are getting power to the coil. If you are pull the wire from coil to distributor on the distributor side, crank and see if you are getting a spark. This was my issue with the 300 which showed me my electronic ignitor went out. Did you do all of this? If you are getting any fuel into the motor it will try and start.
Shawn Agne

User avatar
Jim in SC
5+ Years
5+ Years
Posts: 355
Joined: Mon Sep 15, 2014 10:16 am
Zip Code: 29527
Tractors Owned: 1951 Farmall H - "Ray R." (SN FBH 366519)
1959 Farmall Cub - "Pea" (SN 211538 J)
1964 IH Cub Cadet 100 - (SN 92562)
1971 IH Cub Cadet 106 - (SN 380760)

2018 Husqvarna YTH18542

Tractor previously owned:
1951 Farmall Cub - "Johnny R."
Circle of Safety: Y
Location: Conway, South Carolina

Re: More starting problems

Postby Jim in SC » Tue Apr 23, 2019 6:29 am

Okay, Shawn, I'll try that, but first I'm going to pull the carb to make sure that the throttle valve plate is not somehow hung up and not allowing fuel to flow to the cylinders, i.e. perhaps the throttle shaft didn't get seated right when I last installed the carb. I'm thinking this may well be the problem, the more I think about it. We'll see.
Circle of Safety
"That's the great thing about a tractor. You can't really hear the phone ring."
Jeff Foxworthy

1951 Farmall H
1959 Farmall Cub
1964 IH Cub Cadet 100
1971 IH Cub Cadet 106
2018 Husqvarna YTH18542

User avatar
Jim in SC
5+ Years
5+ Years
Posts: 355
Joined: Mon Sep 15, 2014 10:16 am
Zip Code: 29527
Tractors Owned: 1951 Farmall H - "Ray R." (SN FBH 366519)
1959 Farmall Cub - "Pea" (SN 211538 J)
1964 IH Cub Cadet 100 - (SN 92562)
1971 IH Cub Cadet 106 - (SN 380760)

2018 Husqvarna YTH18542

Tractor previously owned:
1951 Farmall Cub - "Johnny R."
Circle of Safety: Y
Location: Conway, South Carolina

Re: More starting problems

Postby Jim in SC » Tue Sep 08, 2020 6:31 am

I know this is an old thread, but I wanted to put it to rest. I FINALLY finished my H. The starting problems were narrowed down to a bad carburetor, which I had rebuilt by a carb guy in Minnesota, who also knows a bit about electricity, which turned out to be my other problem. He told me that the old 6 volt systems were just fine for starting low compression engines, but that, because of the low voltage, it is critical to have good grounding surfaces everywhere needed on the tractor. He said it was a common problem for tractors that had been "restored, including painting of parts piece by piece." That described mine perfectly. Long story short: I removed the starter, generator, and distributor, then ground off the paint there, which was serving as an insulator. That solved the problem! Starts great now.

I'm including a picture of my H in it's finished state. I also posted the same picture on the Cub section of the forum, because the '59 Cub on the trailer is my next project. I'll remember the no paint on contact surfaces this time though!

Jim
Attachments
sm.jpg
sm.jpg (60.95 KiB) Viewed 671 times
Circle of Safety
"That's the great thing about a tractor. You can't really hear the phone ring."
Jeff Foxworthy

1951 Farmall H
1959 Farmall Cub
1964 IH Cub Cadet 100
1971 IH Cub Cadet 106
2018 Husqvarna YTH18542

oldfarmkid
Cub Star
Cub Star
Posts: 81
Joined: Wed Dec 20, 2017 12:13 am
Zip Code: 29669

Re: More starting problems

Postby oldfarmkid » Sun Sep 13, 2020 8:33 pm

Glad you found all your problems and got everything fixed. Thanks for the update with pics. Also have an H, live in the upstate between Anderson and Greenville.

User avatar
Jim in SC
5+ Years
5+ Years
Posts: 355
Joined: Mon Sep 15, 2014 10:16 am
Zip Code: 29527
Tractors Owned: 1951 Farmall H - "Ray R." (SN FBH 366519)
1959 Farmall Cub - "Pea" (SN 211538 J)
1964 IH Cub Cadet 100 - (SN 92562)
1971 IH Cub Cadet 106 - (SN 380760)

2018 Husqvarna YTH18542

Tractor previously owned:
1951 Farmall Cub - "Johnny R."
Circle of Safety: Y
Location: Conway, South Carolina

Re: More starting problems

Postby Jim in SC » Mon Sep 14, 2020 7:57 pm

oldfarmkid wrote:Glad you found all your problems and got everything fixed. Thanks for the update with pics. Also have an H, live in the upstate between Anderson and Greenville.


I got my H from a fella outside of Fountain Inn. I spent a few years living in Clemson too.
Circle of Safety
"That's the great thing about a tractor. You can't really hear the phone ring."
Jeff Foxworthy

1951 Farmall H
1959 Farmall Cub
1964 IH Cub Cadet 100
1971 IH Cub Cadet 106
2018 Husqvarna YTH18542


  • Similar Topics
    Replies
    Views
    Last post

Return to “Farmall H, HV, Super H, 300 & 350”

Who is online

Users browsing this forum: No registered users and 2 guests