When I asked George originally for this How To, I think one of two things occured . Either George sent it to me as a PM and I simply cut and pasted into this thread, or somehow in the transferral of the post, stuff got lost. Either way, it has now been corrected and a new post under George's ID is now connected to the Cub Book of Knowledge.
This thread is now unlocked and released into the general archives.
[edited by Rudi 09 March 2008 for content]
Rudi ... you asked fot it. You can add it to the how-to files, but maybe wait if see if anyone can suggest anything to make it any clearer than mud?
This is how I make fuel lines...
The lines are interchangeable among my Cubs because I'm careful to have all the sediment bowls tightened so the outlets are all pointing the same way -- at right angles to the center line of the tractor (THIS IS IMPORTANT FOR THIS SYSTEM TO WORK). If you do the same you should be able to make a new line that fits the same way. This also assumes the sediment bowl and IH carburetor have the original threads.
This won't work for tractors with underslung exhaust without some modification.
The line is made from a 20" length of 5/16" brake line available from NAPA with the right fittings already on it. The fittings are the correct 1/2" x 20 thread. The flared ends are cut off and ferrules are used instead. The ferrules will have to be bought separately.
Here's one of my lines with the measurements that work for me:
I recommend making the first bend just a little long and trimming it to the final length. Note the measurement is from the center line of the vertical run to the end. The vertical run is measured between the center lines of the two horizontal runs. The final horizontal run is simply measured from the center line of the vertical to the final end cut.
It may be helpful to note any difference between expected length of the first run and the final result -- so the layout of the second bend can be adjusted accordingly, if necessary.
There are several ways to make the bends. I'll only explain the one I use. Since I don't have a proper bender of the right size I use an old pulley made for round leather belts that makes a 2" radius bend.
I clamp the pulley in the bench vise so I have both hands free. The desired length is measured on the line and the radius is deducted and the spot marked. By placing the mark on the pulley at the point of tangency, the right length will result when the pipe is bent 90 degrees.
Here's where you have to be really careful ... make the second bend in the right direction!
If you have a task to do
and mean to do it, really,
never let it be by halves,
but do it fully-freely... Clarence Topel
All fuel related How To’s can be found here
Moderator: Team Cub
1 post • Page 1 of 1
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger
- Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
- Similar Topics
- Last post
Mon Apr 25, 2016 4:58 pm
Wed Oct 19, 2016 7:33 pm
by Bill Hudson
Fri Jan 13, 2017 11:58 am
by AL Farmall Boy
Fri Jan 12, 2018 10:11 am
Mon Dec 18, 2017 9:48 am
Who is online
Users browsing this forum: No registered users and 1 guest