1000 loader parts

Wed Mar 07, 2007 10:10 am

Does anyone know a sorce for the replacement cutting edge for the bucket? Mine is worn out. Also looking for the return line fitting that screws into the TC fill hole. Thanks

Wed Mar 07, 2007 10:46 am

Bob - Contact WKPoor right here on the forum for that return line fitting.

Wed Mar 07, 2007 10:50 am

Cutting edge is easy: Just go to your local scrapyard and pick up a piece of used cutting edge. You can usually find something suitable from a larger machine that's been worn down to just the right size for your 1000 loader.

As for the plug... You might be able to get that part at your local CaseIH dealer, but I doubt it. The big problem is that the plug hole is a straight thread while normal plumbing is a tapered thread. I remember seeing something about a custom-machined unit some time in the past here.

Re: 1000 loader parts

Wed Mar 07, 2007 11:06 am

BOB K. wrote:Also looking for the return line fitting that screws into the TC fill hole. Thanks

You need to be a little more specific on this. Early ones used pipe thread, later a straight thread with a sealing washer. I'm guessing you have the later style or probably wouldn't need to ask.

fitting

Wed Mar 07, 2007 12:07 pm

i took my plug to a machine shop and had them make me a fitting to match the plug threads not very expensive

Wed Mar 07, 2007 12:42 pm

Yes it is the later stright thread. I had contacted a local shop for the cutting edge. They are alot thicker and he would weld the upright to it. Just didn't know if anyone made them as a repro.

Wed Mar 07, 2007 6:08 pm

Aw heck, a cutting edge is a cutting edge... Do a decent job of welding it on and nobody will be able to tell the difference. Plus, it'll last as long as you live.

Just don't get one for a large excavator or you'll be spending a whole lot of time with your back wheels in the air :D

I'm making an order to SurplusCenter.com for an SAE 14 to 3/4" NPT adapter. In theory, this should thread right into the Touch Control fill port. May need a brass washer to make a seal, but heck, if my hunch isn't correct I'll only be out $6.

Wed Mar 07, 2007 8:35 pm

I have a pretty serious cutting edge that I was going to put on my McCormick plow... but decided against it.... forget how thick, but I can check if you want.
Its yours if you want it... Possibly I could bring it to the CT CubFest.

Wed Mar 07, 2007 9:47 pm

While this post is up where can I find a replacement Bucket for a 1000 loader.

Wed Mar 07, 2007 10:29 pm

I'm sure there are replacement buckets for these compact tractor loaders that are the right width. You could check with Cub Cadet, Kubota, and dare I say John Deere dealers. I don't think you can get a new bucket specifically for that loader anymore.

Wear pants you're not really attached to as you're likely to soil yourself when you find out how much they cost :shock: I know what the big buckets cost, and it's scary. On top of that, these buckets need to be modified for the 1-arm pivot and single cylinder.

If all you need is a new bottom, it may be prudent to find a piece of 3/16" plate, a friend with a welder, and a six pack of your favorite beverage. Heck with enough drink and material you may get him to weld you up an entire new bucket :)

Heck, I'd do it for you but I don't think you live very close to me.

Thu Mar 08, 2007 7:09 am

Matt, My bucket has been modified.And I was looking to restore it but I'm thinking about a fork set up for the loader.

Thu Mar 08, 2007 4:43 pm

Thanks buzzard wing, I am waiting for a price for 1 from a local shop. I will let you know. As far as a bucket goes make 1 if you have the tools. I plan on making a bigger 1 for snow. I make a bucket for a small backhoe. I cut the end plats used 3/16" steel welded the side plates to thesteel and bent it around using a comealong and welding every few inches the bend more and weld and so on. It wasn't that had just takes time.

Thu Mar 08, 2007 4:57 pm

Check with excavating company in your area because they will probably have some laying around both new and used that they may sell.

zack

Thu Mar 08, 2007 6:25 pm

As far as I know Earl is the only one with the adapters. The straight thread is a bastard and you won't find it any were nor will you find the die. Earl makes them on the lathe and his is furnished with a very nice thick copper sealing washer and...... he also has an adapter tee that will allow you to still have a service port with the same thread as the plug so you won't have to throw it in the corner and get lost. He has had a good stock of these for 2 or 3 yrs now.
I've never owned a loader but saw the need while skeeming up an aux. hydraulic mod a couple of yrs ago . I figured over time people would come out of the woodwork looking for them. Earl is way ahead of his time, he's got products sitting on the shelf waiting for the market to realize the need.