Sharpening hole punches

Easy ways to clean parts, remove broken bolts, etc.

Moderators: Barnyard, Team Cub

Bob McCarty
Team Cub Mentor
Team Cub Mentor
501 Club
501 Club
Posts: 7590
Joined: Tue May 25, 2004 8:02 pm
Zip Code: 80501
Tractors Owned: Cubs, MH Pony, Shaw, Allis G, 1934 Silver King, JD LA and LI, Gibson D, David Bradley Tri-Trac
Circle of Safety: Y
Location: CO, Longmont

Sharpening hole punches

Postby Bob McCarty » Thu Jan 05, 2012 4:35 pm

I have an inexpensive set of HF hole punches. This afternoon when I looked at the cutting edges, I realized that even the ones I hadn't used didn't come with a decent edge on them. If I had a lathe, it would be easy to chuck them up to sharpen. My alternative was to chuck the punch in my drill press, and raise the table until it was about 1/8" below the punch. I then took a fine cut triangular file and while holding one side flat against the table, ran it against the cutting edge. In a matter of seconds, I had a sharp and smooth cutting edge. The bevel (which would be 60* if my geometry is correct) looked to be close to the original angle, although I don't feel that would be critical. There are probably other better and possibly easier ways to do this, but this was the first idea I came up with that coincided with what I had available.

Bob
"We don't need to think more,
we need to think differently."
-Albert Einstein

User avatar
Stanton
Team Cub Mentor
Team Cub Mentor
501 Club
501 Club
Posts: 3851
Joined: Mon Jun 22, 2009 6:56 am
Zip Code: 64070
Tractors Owned: 1945 Farmall H, serial #213,651
1947 Farmall Circle Cub, serial #2116
1948 Farmall Cub, serial #46066
Circle of Safety: Y
Location: Lone Jack, MO

Re: Sharpening hole punches

Postby Stanton » Thu Jan 05, 2012 4:43 pm

Thanks for the tip. Might even be "Tip of the Week"!!

Your method sounds like it would be better than trying to hold them by hand at a bench grinder. The only limitation would be the size chuck on a drill press. Fortunately, mine's 1/2" diameter.
Stanton
Image Circle of Safety

User avatar
Bill Hudson
Team Cub
Team Cub
501 Club
501 Club
Posts: 7551
Joined: Wed Jul 26, 2006 10:50 am
Zip Code: 44057
Tractors Owned: 57 F-Cub - Dad & Mom's Cub
57 Lo-Boy
52 F-Cub
49 F-Cub
Circle of Safety: Y
Location: OH, Madison

Re: Sharpening hole punches

Postby Bill Hudson » Thu Jan 05, 2012 4:48 pm

Bob,

Great idea! Now I can sharpen my HF hole punches. :D :D

Bill
"The probability of life originating from accident is comparable to the probability of the unabridged dictionary resulting from an explosion in a printing shop." Edwin Conklin, biologist

User avatar
Rudi
Cub Pro
Cub Pro
501 Club
501 Club
Posts: 28707
Joined: Sun Feb 02, 2003 8:37 pm
Zip Code: E1A7J3
eBay ID: ve9rhs
Skype Name: R.H. "Rudi" Saueracker, SSM
Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger
Circle of Safety: Y
Twitter ID: Rudi Saueracker, SSM
Location: NB Dieppe, Canada

Re: Sharpening hole punches

Postby Rudi » Thu Jan 05, 2012 7:12 pm

Bob:

Yeah, I can see that. I like it. Might be something I try with my Princess Auto Hole Punches :idea: And it just may be a CToTW :D
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship



Return to “Shop Tips”

Who is online

Users browsing this forum: No registered users and 1 guest