This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
"To Double or Not To Double??"
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 84
- Joined: Thu Mar 12, 2009 8:55 pm
- Zip Code: 28430
- Tractors Owned: 1950 Cub (Family Bought New)
1950 Cub
1950 TO-20
"To Double or Not To Double??"
Ok guys and gals, here's my next question, what does everyone think (or know from experience) about doubling any of the seals in the tranny, pto, or final drives As always thanks in advance for the input.
-
- 10+ Years
- Posts: 804
- Joined: Tue Apr 17, 2012 7:55 pm
- Zip Code: 47119
- Skype Name: ntrenn
- Tractors Owned: 63 Cub 221833 in family since '69
65 Lo-boy 19648 with an un-stuck #4 - it lives!!!
144 Cultivators with disc hillers
193 Plow
42C mower
59L mower mounted on the Fcub
23A Disc - lost possession - Circle of Safety: Y
- Location: Indiana
Re: "To Double or Not To Double??"
If you're putting double lip seals in place of single lip seals, there will probably be some benefit, as double lip designs usually are better at sealing.
If you are talking about putting 2 separate seal assemblies into the locations mentioned - the one that runs dry will burn up and you'll still just have a single seal.
Lip seals are designed to leak when they are working correctly, but the leak is supposed to be so small that you can't see it.
If you are talking about putting 2 separate seal assemblies into the locations mentioned - the one that runs dry will burn up and you'll still just have a single seal.
Lip seals are designed to leak when they are working correctly, but the leak is supposed to be so small that you can't see it.
- gitractorman
- 10+ Years
- Posts: 2678
- Joined: Mon Oct 24, 2005 11:35 am
- Zip Code: 14072
- eBay ID: toysforjake
- Tractors Owned: Lots of Cub Cadets!
1951 Farmall Cub
1977 IH Cub
1966 IH Cub
1965 IH Lo Boy
1964 IH Lo Boy
1949 Farmall Cub
Several IH 154 Lo Boys
1979 IH 184 Lo Boy
Simplicity 4416 Sovereign
Simplicity Conquest
Simplicity Legacy 4x4 Diesel
Mitsubishi MT180D 4x4 Diesel - Circle of Safety: Y
- Location: Grand Island, NY
Re: "To Double or Not To Double??"
If you're talking gaskets, I would suggest not doing that. It acutally makes things harder to seal, and was an old "trick" that people used to do just to skip the cleaning and prep process, which is something my dad used to call "half assing it!"
If you want to make sure something does not leak, remove the old seal (ALL OF IT) clean, grind, scrape, wire brush, etc., whatever you need to do to get the mating faces PERFECTLY CLEAN! Then clean again with acetone or whatever your favorite degreaser is. Then clean it again with degreaser. Then maybe clean it again. Get the hint?! Next, depending on the application I will typically use purple Permatex, or Indian Head Permatex, or, whatever the correct gasket sealant is for the application. Follow the directions for application. Lastly, bolt up the appropriate pieces and torque to specs.
By following these steps you are actually making a better gasket installation than was done at the factory, as all factory installed gaskets were done dry, with no sealants. Cork gaskets should seal dry, but the installation of Permatex products greatly enhances this, and makes up for some of the imperfections that may have occurred over the years. Also, the sealants will "help" if for some reason the surfaces are not perfectly clean, or a drop of oil runs across a surface and you don't notice it. Regardless, if you take your time, this is the best way to seal things.
If you want to make sure something does not leak, remove the old seal (ALL OF IT) clean, grind, scrape, wire brush, etc., whatever you need to do to get the mating faces PERFECTLY CLEAN! Then clean again with acetone or whatever your favorite degreaser is. Then clean it again with degreaser. Then maybe clean it again. Get the hint?! Next, depending on the application I will typically use purple Permatex, or Indian Head Permatex, or, whatever the correct gasket sealant is for the application. Follow the directions for application. Lastly, bolt up the appropriate pieces and torque to specs.
By following these steps you are actually making a better gasket installation than was done at the factory, as all factory installed gaskets were done dry, with no sealants. Cork gaskets should seal dry, but the installation of Permatex products greatly enhances this, and makes up for some of the imperfections that may have occurred over the years. Also, the sealants will "help" if for some reason the surfaces are not perfectly clean, or a drop of oil runs across a surface and you don't notice it. Regardless, if you take your time, this is the best way to seal things.
Last edited by gitractorman on Tue Mar 12, 2013 6:35 am, edited 1 time in total.
Cub Cadets 682, 1811, 1864, Simplicity Legacy XL 4x4 Diesel with FEL, 60" mower, 50" Tiller
-
- 10+ Years
- Posts: 84
- Joined: Thu Mar 12, 2009 8:55 pm
- Zip Code: 28430
- Tractors Owned: 1950 Cub (Family Bought New)
1950 Cub
1950 TO-20
Re: "To Double or Not To Double??"
sounds good to me. everything sounds very logical (like the outer seal burning up) although I don't know if I will be creating enough heat in there for that to be a problem since it won't actually work anymore. I remember my father using this method years ago but probably because he didn't want to replace the parts that were causing the leaks in the first place like grooves wore in shafts and such. The local industrial seal and bearing store actually suggested doubling the seal that surrounds the axle nut on the right side final drive due to the difference in thickness. So it looks like i'm better off to only us single seals and be sure to use some type of sealant on gaskets. Almost forgot,,,,clean,,,,clean,,,,,and clean some more to remove the 65 years worth of dirt and such. Sure am glad I ask. This is such a great site, don't know what I would do without it or the members on it
-
- 10+ Years
- Posts: 4947
- Joined: Tue Jun 08, 2004 3:04 pm
- Zip Code: 14559
- Circle of Safety: Y
- Location: Rochester, NY
Re: "To Double or Not To Double??"
We're not talking about literally catching fire here. It's a figure of speech.
The outer seal will not receive any lubrication because the inner seal is preventing oil from leaking. Dry seal against dry shaft will quickly wear away the rubber lip and probably put a groove in the shaft too, even if you are not working the tractor. It's not a heat thing but it is a friction thing.
The outer seal will not receive any lubrication because the inner seal is preventing oil from leaking. Dry seal against dry shaft will quickly wear away the rubber lip and probably put a groove in the shaft too, even if you are not working the tractor. It's not a heat thing but it is a friction thing.
- John *.?-!.* cub owner
- Cub Pro
- Posts: 23701
- Joined: Sun Feb 02, 2003 2:09 pm
- Zip Code: 63664
- Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
- Location: Mo, Potosi
Re: "To Double or Not To Double??"
Some of the seals on the older rigs, such as the brake drum shafts on H had that type originally, but the new ones are singles. The material the newer seals are made from are much better, and do not leak as easily. My personal opinion, which is worth about what I charged for it, is that it is a waste of money. Until the inner seal fails there will be no oil getting to it to lubricate where it runs on the shaft, and it will be worn to the point of not being effective by the time the inner one fails. The exception to this is if the shaft for the inner one is bad, and it leaks, then the second one would help.
If you are not part of the solution,
you are part of the problem!!!
you are part of the problem!!!
- ricky racer
- 10+ Years
- Posts: 6315
- Joined: Wed Sep 12, 2007 8:40 pm
- Zip Code: 49120
- Circle of Safety: Y
- Location: Niles / Buchanan, Michigan
Re: "To Double or Not To Double??"
I agree with gitractorman regarding gaskets. Also, keep in mind that some gaskets are made to a specific thickness to act as a spacer or shim to set clearances. The oil pump gasket comes to mind as well as the gaskets used on some governors.
Regarding the use of double seals, as a machine builder for over well over 20 years, I've seen it used sometimes in areas that historically are difficult to seal. When ever I installed double seals in an application, I hand packed grease in between each of the seals to provide lubrication for the outer seal. Also sometimes the seals are installed opposed to one another with the inner seal "lip in" to keep oil or grease in the housing and the outer seal mounted "lip out" to keep water, dust or other debris from getting into the housing. Again, I pack grease between the seals when installing.
Regarding the use of double seals, as a machine builder for over well over 20 years, I've seen it used sometimes in areas that historically are difficult to seal. When ever I installed double seals in an application, I hand packed grease in between each of the seals to provide lubrication for the outer seal. Also sometimes the seals are installed opposed to one another with the inner seal "lip in" to keep oil or grease in the housing and the outer seal mounted "lip out" to keep water, dust or other debris from getting into the housing. Again, I pack grease between the seals when installing.
1929 Farmall Regular
1935 John Deere B
1937 John Deere A
1941 John Deere H
1952 John Deere B
1953 Farmall Cub
1935 John Deere B
1937 John Deere A
1941 John Deere H
1952 John Deere B
1953 Farmall Cub
-
- 10+ Years
- Posts: 804
- Joined: Tue Apr 17, 2012 7:55 pm
- Zip Code: 47119
- Skype Name: ntrenn
- Tractors Owned: 63 Cub 221833 in family since '69
65 Lo-boy 19648 with an un-stuck #4 - it lives!!!
144 Cultivators with disc hillers
193 Plow
42C mower
59L mower mounted on the Fcub
23A Disc - lost possession - Circle of Safety: Y
- Location: Indiana
Re: "To Double or Not To Double??"
In the OE game, we worked really hard at getting gasket coatings that would NOT stick to the housings - at least in the short term. Years ago I was testing new gasket formulations and picked up a 1800 lb transmission by the gasket that stuck the 2 housings together. We quickly ordered a new coating formula.
- John *.?-!.* cub owner
- Cub Pro
- Posts: 23701
- Joined: Sun Feb 02, 2003 2:09 pm
- Zip Code: 63664
- Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
- Location: Mo, Potosi
Re: "To Double or Not To Double??"
Never tried it, but I once heard that chap stick was good to keep carburetor gaskets from sticking
If you are not part of the solution,
you are part of the problem!!!
you are part of the problem!!!
- clodhopper
- 10+ Years
- Posts: 807
- Joined: Sat May 07, 2011 8:20 pm
- Zip Code: 27526
- Tractors Owned: 1950 Cub Demo
1978 Cub Cadet 1650
cub 193 plow
cub 174 planter
cub sidedresser
cub 144 cultivator
cadet 50C deck - Circle of Safety: Y
Re: "To Double or Not To Double??"
gitractorman wrote:If you want to make sure something does not leak, remove the old seal (ALL OF IT) clean, grind, scrape, wire brush, etc., whatever you need to do to get the mating faces PERFECTLY CLEAN! Then clean again with acetone or whatever your favorite degreaser is. Then clean it again with degreaser. Then maybe clean it again.
Who is online
Users browsing this forum: No registered users and 3 guests