This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
C-22 pitman arm drawing
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 5+ Years
- Posts: 157
- Joined: Sun Sep 30, 2018 3:09 pm
- Zip Code: 06482
- Circle of Safety: Y
C-22 pitman arm drawing
As i'm continuing to learn, about my tractor, mower, and this site, i think i've learned that what is commonly referred to here as Rudi's server, i believe cleancomputers or something like that, is offline. i'm looking for a drawing for the pitman arm on my cub 22 sickle mower because i have time, and woodworking abilities and tools and would like to make one. I've found several posts from 2006, 8, 9, and 12 mentioning the drawing even with a link, but the link is broken. then i went down the rabbit hole of the old server, and how many gigs of data there are/was and moving things and recreating, but i am having zero luck locating a drawing for the pitman arm. I read where tractor supply used to sell them, they don't anymore at least mine doesn't and online search at tsc doesn't recognize the words or part numbers. i looked in the how to, implement section, and searched 6 ways till Sunday but i cannot find a drawing. what am i missing? someone always pops up and points me in the right direction. my grass board is done, i made that from scratch and am waiting for the stencil from my brother to paint McCormick on it, but it's a nice bright Caterpillar Yellow (funny to have yellow paint on the shelf now besides all the red and blue.) Anyway, i would be very grateful if someone could point me in the right direction for a drawing with the correct dimensions (i got a HOWL reading about how someone's pitman arm wasn't short on either end, but short in the middle!! HAHAHHAH!) Thanks in advance very much
chris
chris
-
- Cub Pro
- Posts: 7503
- Joined: Thu Aug 31, 2006 7:00 pm
- Zip Code: 02769
- Tractors Owned: 6"F" cubs
5 lo-boys
1 154
1 184
1 IH444
1 Oliver OC3 crawler
1 AC D10
1 IH 100 manure spreader
1 IH model B corn grinder
3 power units
cub demonstrator - Circle of Safety: Y
- Location: Ma. Rehoboth
Re: C-22 pitman arm drawing
TM tractor sells them. (Site sponsor)
Ed
Ed
- Glen
- 10+ Years
- Posts: 6113
- Joined: Mon Mar 19, 2012 7:33 pm
- Zip Code: 00000
- Tractors Owned: 1956 Farmall Cub with Fast Hitch, F-11 plow, Disc, Cultivator, Cub-22 mower
- Circle of Safety: Y
- Location: Wa.
Re: C-22 pitman arm drawing
Hi,
Below is a listing at TM Tractor for a new pitman. You can look at the pics.
Case IH might still sell them too.
http://www.tmtractor.com/new/sm/951fp.htm
Below is a listing at TM Tractor for a new pitman. You can look at the pics.
Case IH might still sell them too.
http://www.tmtractor.com/new/sm/951fp.htm
- ddlebail
- Posts: 41
- Joined: Wed Jul 17, 2019 6:35 am
- Zip Code: E1N6B5
- Tractors Owned: :
1960 Farmall Cub
1979 Ford 1700 4X4 - Location: Miramichi, New Brunswick, Canada
Re: C-22 pitman arm drawing
The length for the wooden pitman i have recorded as 30 3/4 inches
The hole in the end for the spring I have is 3/4" dia at 1 5/8" deep
These numbers are ones I have noted on my phone.
I will grab the pitman i removed when I replaced mine and get more measurements if required.
I know the one I have for a pattern is not an original, but it was made with the original as a template.
The hole in the end for the spring I have is 3/4" dia at 1 5/8" deep
These numbers are ones I have noted on my phone.
I will grab the pitman i removed when I replaced mine and get more measurements if required.
I know the one I have for a pattern is not an original, but it was made with the original as a template.
- Barnyard
- Team Cub
- Posts: 24238
- Joined: Tue Aug 07, 2007 3:39 pm
- Zip Code: 45030
- Tractors Owned: At This Time
40 Farmall Cubs (Round Hood)
2 Farmall Cub (Square Hood)
2 IH Cubs (Square Hood)
5 Lo-Boys (Round Hood)
2 Lo-Boys (Square Hood)
2 Farmall 404's
1 Farmall H
1 Ferguson 20
1 Cub Cadet 125
1 Kubota B-7100 - Circle of Safety: Y
- Location: OH, New Haven (Hamilton County)
- Contact:
Re: C-22 pitman arm drawing
I knew I had saved it just before Rudi's site crashed, but I couldn't remember where.
There are two ways to get enough Cubs. One is to continue to accumulate more and more. The other is to desire less.
-
- 5+ Years
- Posts: 157
- Joined: Sun Sep 30, 2018 3:09 pm
- Zip Code: 06482
- Circle of Safety: Y
Re: C-22 pitman arm drawing
Perfect thank you barnyard and ddlbail! I don’t feel so bad it wasn’t here!
C
C
- T-Mo
- 5+ Years
- Posts: 2009
- Joined: Tue May 16, 2017 9:25 am
- Zip Code: 63628
- Tractors Owned: '40 H
'44 B
'47 Cub
'49 C
54A Blade
42 Woods Mower
Henderson Loader
Cultivators
No. 8 Little Genius 2-12 Plow
IH Running Gear - Circle of Safety: Y
- Location: Bonne Terre, Mo
Re: C-22 pitman arm drawing
I probably can make a good 2D drawing to add to the pdf manual section here. How wide is the slit for the driving shaft plate and the gap between the holes? Hole diameters? I see the one that is 1.375 drilled parallel to the length is .75 but I don't know what the other holes are?
- SONNY
- 10+ Years
- Posts: 4087
- Joined: Thu Nov 09, 2006 11:26 pm
- Zip Code: 61722
Re: C-22 pitman arm drawing
I never did measure the plate thickness,---always just guessed!---Hmmmm Might have to get ole caliper out and go measure it! --- I made a couple over the years, but I just guessed all the length/hole sizes/etc.-----they always worked!
-
- 5+ Years
- Posts: 157
- Joined: Sun Sep 30, 2018 3:09 pm
- Zip Code: 06482
- Circle of Safety: Y
Re: C-22 pitman arm drawing
hi T-Mo. I'm an autocad draftsman, i was going to do just that tomorrow morning... since i have everything but the pitman (i actually do, made a temporary one from pressure treated when my old one rotted and just kind of gave up the ghost) it's not the right length so i know things aren't timed properly, but with Rudi's drawing from barnyard i was going to draw it in the morning.
c
c
- ddlebail
- Posts: 41
- Joined: Wed Jul 17, 2019 6:35 am
- Zip Code: E1N6B5
- Tractors Owned: :
1960 Farmall Cub
1979 Ford 1700 4X4 - Location: Miramichi, New Brunswick, Canada
Re: C-22 pitman arm drawing
Drive end 1.5 “ spacing 5/16 hole in plate
Blade end 1 5/16” spacing 5/16 hole in clamp
plate thickness 3/32"
Measurements are of hardware not the pitman arm.
I am fairly certain they were 1/4 bolts used for fasteners.
Blade end 1 5/16” spacing 5/16 hole in clamp
plate thickness 3/32"
Measurements are of hardware not the pitman arm.
I am fairly certain they were 1/4 bolts used for fasteners.
-
- Team Cub
- Posts: 17240
- Joined: Sun Feb 02, 2003 2:59 pm
- Zip Code: 55319
- Circle of Safety: Y
- Location: MN
Re: C-22 pitman arm drawing
Parts catalog calls out 5/16 diameter bolts.
- T-Mo
- 5+ Years
- Posts: 2009
- Joined: Tue May 16, 2017 9:25 am
- Zip Code: 63628
- Tractors Owned: '40 H
'44 B
'47 Cub
'49 C
54A Blade
42 Woods Mower
Henderson Loader
Cultivators
No. 8 Little Genius 2-12 Plow
IH Running Gear - Circle of Safety: Y
- Location: Bonne Terre, Mo
Re: C-22 pitman arm drawing
Preliminary drawing
- Attachments
-
- C-22 PITMAN ARM.pdf
- (20.16 KiB) Downloaded 534 times
- Don McCombs
- Team Cub Mentor
- Posts: 17442
- Joined: Mon Feb 03, 2003 6:45 am
- Zip Code: 21550
- Tractors Owned: "1950 Something" Farmall Cub
1957 Farmall Cub w/FH
1977 International Cub w/FH
1978 International Cub
1948 Farmall Super A - Circle of Safety: Y
- Location: MD, Deep Creek Lake
Re: C-22 pitman arm drawing
Looking good, Terry. Thank you!
- Dusty B
- 10+ Years
- Posts: 1880
- Joined: Wed May 23, 2007 7:35 am
- Zip Code: 61736
- Tractors Owned: '45 SC Case
- Circle of Safety: Y
- Location: IL, Downs
- Contact:
Re: C-22 pitman arm drawing
Neighbor (woodworker) made 4 of them for me! Have used them all,! Dusty B
Grandpa's '41 B
'56,,'57,'59, Cu'b
'45 C
'55 Case S
Dad's DB garden tractor
'48 DeSoto
'31 "A Coup
'79 Lincoln TC
God looks out for those of us who don't know how to look out for ourselves!
'56,,'57,'59, Cu'b
'45 C
'55 Case S
Dad's DB garden tractor
'48 DeSoto
'31 "A Coup
'79 Lincoln TC
God looks out for those of us who don't know how to look out for ourselves!
- T-Mo
- 5+ Years
- Posts: 2009
- Joined: Tue May 16, 2017 9:25 am
- Zip Code: 63628
- Tractors Owned: '40 H
'44 B
'47 Cub
'49 C
54A Blade
42 Woods Mower
Henderson Loader
Cultivators
No. 8 Little Genius 2-12 Plow
IH Running Gear - Circle of Safety: Y
- Location: Bonne Terre, Mo
Re: C-22 pitman arm drawing
I can get Dennis to load the drawing into the pdf manual section, but I would like to see if there are any comments that I may have to incorporate first.
Who is online
Users browsing this forum: No registered users and 28 guests