Farmall Cub

As i'm continuing to learn, about my tractor, mower, and this site, i think i've learned that what is commonly referred to here as Rudi's server, i believe cleancomputers or something like that, is offline. i'm looking for a drawing for the pitman arm on my cub 22 sickle mower because i have time, and woodworking abilities and tools and would like to make one. I've found several posts from 2006, 8, 9, and 12 mentioning the drawing even with a link, but the link is broken. then i went down the rabbit hole of the old server, and how many gigs of data there are/was and moving things and recreating, but i am having zero luck locating a drawing for the pitman arm. I read where tractor supply used to sell them, they don't anymore at least mine doesn't and online search at tsc doesn't recognize the words or part numbers. i looked in the how to, implement section, and searched 6 ways till Sunday but i cannot find a drawing. what am i missing? someone always pops up and points me in the right direction. my grass board is done, i made that from scratch and am waiting for the stencil from my brother to paint McCormick on it, but it's a nice bright Caterpillar Yellow (funny to have yellow paint on the shelf now besides all the red and blue.) Anyway, i would be very grateful if someone could point me in the right direction for a drawing with the correct dimensions (i got a HOWL reading about how someone's pitman arm wasn't short on either end, but short in the middle!! HAHAHHAH!) Thanks in advance very much
chris

TM tractor sells them. (Site sponsor)
Ed

Hi,
Below is a listing at TM Tractor for a new pitman. You can look at the pics.
Case IH might still sell them too.

http://www.tmtractor.com/new/sm/951fp.htm

The length for the wooden pitman i have recorded as 30 3/4 inches
The hole in the end for the spring I have is 3/4" dia at 1 5/8" deep
These numbers are ones I have noted on my phone.
I will grab the pitman i removed when I replaced mine and get more measurements if required.
I know the one I have for a pattern is not an original, but it was made with the original as a template.

I knew I had saved it just before Rudi's site crashed, but I couldn't remember where.

Perfect thank you barnyard and ddlbail! I don’t feel so bad it wasn’t here!
C

I probably can make a good 2D drawing to add to the pdf manual section here. How wide is the slit for the driving shaft plate and the gap between the holes? Hole diameters? I see the one that is 1.375 drilled parallel to the length is .75 but I don't know what the other holes are?

I never did measure the plate thickness,---always just guessed!---Hmmmm Might have to get ole caliper out and go measure it! --- I made a couple over the years, but I just guessed all the length/hole sizes/etc.-----they always worked!

hi T-Mo. I'm an autocad draftsman, i was going to do just that tomorrow morning... since i have everything but the pitman (i actually do, made a temporary one from pressure treated when my old one rotted and just kind of gave up the ghost) it's not the right length so i know things aren't timed properly, but with Rudi's drawing from barnyard i was going to draw it in the morning.
c

Drive end 1.5 “ spacing 5/16 hole in plate
Blade end 1 5/16” spacing 5/16 hole in clamp
plate thickness 3/32"
Measurements are of hardware not the pitman arm.
I am fairly certain they were 1/4 bolts used for fasteners.

Parts catalog calls out 5/16 diameter bolts.

Preliminary drawing

Looking good, Terry. Thank you!

Neighbor (woodworker) made 4 of them for me! Have used them all,! Dusty B

I can get Dennis to load the drawing into the pdf manual section, but I would like to see if there are any comments that I may have to incorporate first.