Leveling and grading blade CUB -54

[danovercash]

Just had my frame blasted. Looking at them, they looked a little different and while priming I found an "L" on one of them so they must be different. The TT mount is not centered with the frame.

[coppersmythe]

good morning fred , from the deep south , looks like these guys got you covered , just shows what level the folks on this website work at coppersmythe................

[bob in CT]

good morning fred , from the deep south , looks like these guys got you covered , just shows what level the folks on this website work at coppersmythe................

There is a LOT of covering yet to do.

[bob in CT]

Calling all volunteers!


My big assemblies are under 3 feet of snow. All of the parts from the page below except for #2 and the substitute drawbar parts need dimensions.




on this page, we have the shoes (7) and the parts welded on the back of the blade drawn. I think the two parts that get sandwiched together with the pin holes in assembly 2 are drawn. I may not see this for some time as it is on the North side of the barn.

[Fredy the frenchy]

Postby bob in CT » Sat Mar 07, 2015 5:11 pm

What link? Cleancomputes? What browser are you using?

Hello bob,

Cleancomputes the link will open with google but after all the links of the page Implement and Part Sketches does not open.
if anyone knows how to do or want me to send them to my email pdf I'm interested.
thank you for all your help.
fred

[bob in CT]

Postby bob in CT » Sat Mar 07, 2015 5:11 pm

What link? Cleancomputes? What browser are you using?

Hello bob,

Cleancomputes the link will open with google but after all the links of the page Implement and Part Sketches does not open.
if anyone knows how to do or want me to send them to my email pdf I'm interested.
thank you for all your help.
fred

I sent you all the pdfs on Cleancomputes after assembling them all in one document. The rest will have to be sketched.

[Fredy the frenchy]

hello,
for reperes8,9,10 of the first page I "ve this sketch I think it's good.http://www.google.fr/imgres?imgurl=http ... J8BEK0DMCg
fred

[bob in CT]

There are THREE VERSIONS of this attachment. I have been sending you diagrams for the NEWEST version only. The original IH part number is not on the sketch, like I did for the group of parts I sent to you so far. For anyone making drawings in the future, I suggest the original IH part number be put somewhere on the print if possible. Makes it a lot easier a few years in the future.

The parts in that sketch are not part of the original blade but are what is known as a "substitute draw bar" It is useful, but not part of the attachment. They should be the last parts you build.

[bob in CT]

[Fredy the frenchy]

tank you
fred

[Fredy the frenchy]

Good evening, is what you 'd be possible to send me pictures of other parties with the dimensions of the blade
thank you

[bob in CT]

I was thinking about that last week. Been a busy summer and I just finished some barn renovations including a new roof. Someone was going to help me with some drawings, but they never followed through. I have the painted parts in the garage so as soon as the weather pushes me inside, I'll have some time to review what I need to send to finish the job. That will work out for me as I can build the assemblies up after I sketch them.

[Fredy the frenchy]

Thank you , I'm not squeeze I just finished the roof of my studio , I have moved in and after I would start to restore farmall cub

[Clip]

Fredy, I'd been trying to help Bob get some of the drawings done for you but a change of jobs left me without access to Solidworks. PM me your email address and I'll send you what I've got, I believe it was one or two parts.

[Fredy the frenchy]

Hello, thank you for your help I sent you .
Thank you
Fredy