I'm looking through the manuals on the website and can't find the procedures for setting the governor.
Where can this be found?
Also in the manual it says my zenith carb is supposed to have a throttle stop screw. Problem is it doesn't.
We are trying to set the low and high idles.
Governor setting proceedures
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 5+ Years
- Posts: 825
- Joined: Sat May 07, 2016 5:13 pm
- Zip Code: 45380
- Tractors Owned: 1952 Cub w/ 184 motor (Kid)
12V with Petronix
IH 3160 Mower Deck
54 Leveling Blade
193 Plow
IH528 Trailer
Front/Rear Weights
1955 Farmall 300 (Clarence)
12V with Petronix
Woods L306 72"
1955 Farmall 100 (Thomas)
12V with Petronix
Woods L59 60"
A60 Leveling Blade
Front/Rear Weights - Circle of Safety: Y
- Location: Versailles, Ohio
Governor setting proceedures
Shawn Agne
-
- 5+ Years
- Posts: 2751
- Joined: Wed Jul 08, 2015 10:24 am
- Zip Code: 19342
- Tractors Owned: 1948 6v - Dozer
1949 with kub klipper belly mower. mag 6v - Mom
1950 with plow, 54 blade, mott mag 6v - Roxanne
1953 54 blade, c22, wood 42 6v
1957 6v - barn Queen
1965 lo-boy with c-3 mower 12 v - Loboy
1974 Horse II 12 v c-2
1975 with woods 42-6 12 v - Horse
1979 long strip 12 v stuck engine
130 with international 1000 loader 6 v
1969 140 with bush hog tow behind mower 12 v
Terramite T-6 4WD Backhoe Perkins diesel
Memberships: Rough and Tumble Engineers Historical Association;Chapter 8 IH Collectors; IH Collectors Worldwide - Circle of Safety: Y
- Location: Glen Mills PA
Re: Governor setting proceedures
this is from the service manual for the c-123 c135 c146c153 engines 1977 GSS-1295J W rev 2
The cub has everything in the parts and service manual but the large tractors need a parts manuals for the tractor and the engine and the service manuals for the tractor and engine (4 in total) to get all of the info.
The cub has everything in the parts and service manual but the large tractors need a parts manuals for the tractor and the engine and the service manuals for the tractor and engine (4 in total) to get all of the info.
When you only have 9 horsepower you need to know the names of all of the ponies!
-
- 5+ Years
- Posts: 825
- Joined: Sat May 07, 2016 5:13 pm
- Zip Code: 45380
- Tractors Owned: 1952 Cub w/ 184 motor (Kid)
12V with Petronix
IH 3160 Mower Deck
54 Leveling Blade
193 Plow
IH528 Trailer
Front/Rear Weights
1955 Farmall 300 (Clarence)
12V with Petronix
Woods L306 72"
1955 Farmall 100 (Thomas)
12V with Petronix
Woods L59 60"
A60 Leveling Blade
Front/Rear Weights - Circle of Safety: Y
- Location: Versailles, Ohio
-
- Team Cub
- Posts: 17109
- Joined: Sun Feb 02, 2003 2:59 pm
- Zip Code: 55319
- Circle of Safety: Y
- Location: MN
Re: Governor setting proceedures
ShawnAgne wrote:. . . Also in the manual it says my zenith carb is supposed to have a throttle stop screw. Problem is it doesn't. . . .
Fell out and was lost? Is there a place to put one at the throttle shaft arm?
-
- 5+ Years
- Posts: 825
- Joined: Sat May 07, 2016 5:13 pm
- Zip Code: 45380
- Tractors Owned: 1952 Cub w/ 184 motor (Kid)
12V with Petronix
IH 3160 Mower Deck
54 Leveling Blade
193 Plow
IH528 Trailer
Front/Rear Weights
1955 Farmall 300 (Clarence)
12V with Petronix
Woods L306 72"
1955 Farmall 100 (Thomas)
12V with Petronix
Woods L59 60"
A60 Leveling Blade
Front/Rear Weights - Circle of Safety: Y
- Location: Versailles, Ohio
Re: Governor setting proceedures
Well we have a rebuild kit, I didn't do it, my friend did so just wondering if the wrong arm got installed. I'll have to take a look Saturday
Shawn Agne
-
- 10+ Years
- Posts: 271
- Joined: Fri Apr 03, 2009 11:37 pm
- Zip Code: 00000
Re: Governor setting proceedures
This is the adjustment for carburetor / governor linkage out the Serviceman's Guide for Farmall A and B .
-
- Similar Topics
- Replies
- Views
- Last post
-
-
Setting the timing on a 100
by customcutter » Wed May 10, 2023 2:35 pm » in Farmall A, Super A, AV, 100, 130 & 140 - 14
- 329
-
by customcutter
Sat May 13, 2023 4:50 pm
-
-
-
Off setting the mower extension on draw bar?
by inairam » Mon May 15, 2023 9:10 am » in Farmall A, Super A, AV, 100, 130 & 140 - 2
- 164
-
by inairam
Sun May 21, 2023 6:33 pm
-
-
- 1
- 135
-
by inairam
Fri Apr 22, 2022 6:20 am
-
-
Help with 140 governor
by M6Scout » Sat Jan 23, 2021 7:32 pm » in Farmall A, Super A, AV, 100, 130 & 140 - 4
- 316
-
by M6Scout
Sun Jan 24, 2021 4:51 pm
-
-
- 2
- 115
-
by tst
Wed Aug 09, 2023 9:21 am
Return to “Farmall A, Super A, AV, 100, 130 & 140”
Who is online
Users browsing this forum: No registered users and 0 guests