Rudi wrote:Using what you got to make the tool you needRudi wrote:This weeks "Cub Tip of the Week" is courtesy of: :by dickcub50 on Thu May 30, 2013 11:28 pm Post subject: Re: Brake pedal
Brake Pedal Puller Tool
Thanks for your help, mission accomplished. Made a puller from a piece
of 2- 3/8" sq. tubing. Cut 3/4" slot and welded the piece on top. Drilled
and taped 1/2-20 NF. Had kroil oil in peddle for 24 hours and used puller
the brake peddle cam off easily.
Cub Tip of the Week!
-
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger - Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
Cub Tip of the Week! May 31, 2013
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship
-
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger - Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
Re: Cub Tip of the Week! August 23, 2013
Rudi wrote:Using what you got to make the tool you need - installment #2Rudi wrote:This weeks "Cub Tip of the Week" is courtesy of:by John *.?-!.* cub owner on Thu May 30, 2013 11:28 pm Post subject: removing roll pins
How To Remove Roll Pins Easily
I learned a trick for removing spring type roll pins today. I was working on the throttle of Jeff's (non mechanic neighbor) 444 today and needed to get the lower roll pin in this picture out to replace the friction disk.
In addition to it being hard to get too, there appeared to be some weld gobbed around the pin, which I had to cut off with the Dremel. I tried to drive it out with a punch, but couldn't move it due to not being able to backup the shaft and keep it from sprining. I tried drilling it, but all I accomplished was dulling my drill bit. After thinking a little bit I remembered Jeff mentioning he was wondering about using an air chisel. I grabbed my air chisel and ground the punch bit that came with it down to the size of the roll pin, and the pin popped out almost as soon as I pulled the trigger. I think I will get some extra punches to grind down to pin sizes as I need them.
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship
-
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger - Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
Re: Cub Tip of the Week! June 09, 2014
Rudi wrote:I wonder if this is what Momma meant when she asked if you was popping your cork
Rudi wrote:This weeks "Cub Tip of the Week" is courtesy of:by TNMike on Thu May 30, 2013 11:28 pm Post subject: Re: East Tennessee - won't start
How To Find TDC by Using a Cork
Well fellers
I stuck a cork in the #1 plug hole and when it popped out, I lined up the mark and the rotor was 180 degrees off. Timed the mag again and she fired right up!!!! Man I was so glad!!! Thank you guys for the help and thanks to the board for all the how to stuff?
Now I'll keep my word...where can I send the parts to?
woohoo!
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship
Return to “Forum Rules, Suggestions, Feedback & Information”
Who is online
Users browsing this forum: No registered users and 0 guests