Bash Projects

The new home for CubFest and Tractor show Announcements & Discussions.
Forum rules
ALL CubFest discussion posted in other forums will be moved to this forum without advance notice.

IMPORTANT NOTE: CubFest organizers -- Notify a TeamCub member or the ADMIN (Dennis) to "Sticky" your event announcement in this forum.
Jim Becker
Team Cub
Team Cub
Posts: 17197
Joined: Sun Feb 02, 2003 2:59 pm
Zip Code: 55319
Circle of Safety: Y
Location: MN

Re: Bash Projects

Postby Jim Becker » Mon May 27, 2019 9:16 pm

3/16 OD? What are you working on, a pocket watch?

cubbrian
10+ Years
10+ Years
Posts: 915
Joined: Sun Apr 08, 2007 7:47 pm
Zip Code: 47631
Tractors Owned: 1955 Cub w/9 different 1 point implements
1948 Cub
1948 McCormick W-6
1949 H
1949 M
1961 560 w/ 412 fast hitch plow
1966 140
1973 666
Allis Chalmers C w/sickle mower
Case 400
Economy 14 hp tractor
Location: IN, New Harmony

Re: Bash Projects

Postby cubbrian » Mon May 27, 2019 9:52 pm

Throttle shaft bushing on a super mta carburetor.

Gary Dotson
Team Cub Mentor
Team Cub Mentor
Posts: 5594
Joined: Thu Aug 03, 2006 6:20 am
Zip Code: 43358
Tractors Owned: 48 Cub Diesel (Cubota)
53 Cockshutt 20 restored (Shooter)
52 Cockshutt 20 unrestored
47 Leader "B" (Herckie)
49 Leader "D" (Princess)
49 Leader "D" very rough
48 Leader "D" unrestored
Kubota B6200E
Kubota B6200HST
Kubota B8200HST-D
Circle of Safety: Y
Location: OH West Mansfield

Re: Bash Projects

Postby Gary Dotson » Tue May 28, 2019 6:39 am

Dale, I'll have a pilot bushing reamer.

User avatar
Dale Finch
10+ Years
10+ Years
Posts: 6601
Joined: Tue Apr 27, 2010 11:34 am
Zip Code: 27517
Tractors Owned: '51 Cub #140966 "Bruno" with Woods 59 mower
'55 Cub #187541 "Betty" with Fast Hitch
'55 Cub #190482 "Ben" with Woods 42 mower
'55 Cub #191739 "Bertha" with Woods 42 mower
'56 Cub #194370 "Boris" with Mott Flail mower
Circle of Safety: Y
Location: NC, Chapel Hill

Re: Bash Projects

Postby Dale Finch » Tue May 28, 2019 2:34 pm

Oh, thanks, Gary!

I'm just leaving Roanoke, VA. A small side trip to pick up a 4E Hammermill that I am Expressing.
20190528_130736-1328x747.jpg

20190528_130815-1328x747.jpg

Then the obligatory stop at their Northern Tool to replace a dead battery jumpbox/compressor on sale from $149 to $99 less my $20 off coupon...FORCED to buy a bag of M&M's to get over the $100!!! :lol:
20190528_152555-1328x747.jpg
Dale Finch
Image
Circle of Safety

User avatar
Dale Finch
10+ Years
10+ Years
Posts: 6601
Joined: Tue Apr 27, 2010 11:34 am
Zip Code: 27517
Tractors Owned: '51 Cub #140966 "Bruno" with Woods 59 mower
'55 Cub #187541 "Betty" with Fast Hitch
'55 Cub #190482 "Ben" with Woods 42 mower
'55 Cub #191739 "Bertha" with Woods 42 mower
'56 Cub #194370 "Boris" with Mott Flail mower
Circle of Safety: Y
Location: NC, Chapel Hill

Re: Bash Projects

Postby Dale Finch » Sun Jun 16, 2019 1:59 pm

Was sorting through photos, and decided to post a couple of the projects that were done by some super folks...THANKS again, all!!

I had a few of the PTO Shifter Levers that I had replaced over the years, intending to repair them per a HOW TO someone posted a while back. However, I have neither the equipment nor the skills to do it, SO enter Gary Dodson!! My hero! :{_}:

First, he drill out the old worn pin:
20190531_181516-1328x747.jpg

20190531_182625-1328x747.jpg

Then he welded in a section of 1/4" drill bit (we were unsure of the required length, so will need to grind it down later):
20190531_182612-1328x747.jpg
Dale Finch
Image
Circle of Safety

User avatar
Dale Finch
10+ Years
10+ Years
Posts: 6601
Joined: Tue Apr 27, 2010 11:34 am
Zip Code: 27517
Tractors Owned: '51 Cub #140966 "Bruno" with Woods 59 mower
'55 Cub #187541 "Betty" with Fast Hitch
'55 Cub #190482 "Ben" with Woods 42 mower
'55 Cub #191739 "Bertha" with Woods 42 mower
'56 Cub #194370 "Boris" with Mott Flail mower
Circle of Safety: Y
Location: NC, Chapel Hill

Re: Bash Projects

Postby Dale Finch » Sun Jun 16, 2019 2:17 pm

After completing a DOUBLE tractor split.....
20190531_160201-1328x747.jpg

20190531_152717-1328x747.jpg

......we relaxed under the big shade tree, listening to Ron play his banjo. Meanwhile, I managed to pull a Tom Sawyer moment, "allowing" Ron's brother to sharpen my Mott Flail Mower Knives, but only after he diagnosed and repaired a problem with my "new-to-me" electric sharpener!!
20190601_153022-747x1328.jpg

20190601_153104-1328x747.jpg

20190601_154015-1328x747.jpg

20190601_153028-747x1328.jpg

We made an attempt to mow a bit at Barnyards, but unfortunately, his grass is like wire!! Took me a while at home to cut that stuff off the cutter bar! However, with "normal" grass here at my farm, it mowed great! Thanks "Ron's Brother" and those that helped with their supervision!!
Dale Finch
Image
Circle of Safety


  • Similar Topics
    Replies
    Views
    Last post

Return to “CubFest and Tractor Show Announcements & Discussions”

Who is online

Users browsing this forum: No registered users and 1 guest