This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Time to rebuild the touch control?
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 178
- Joined: Sat Feb 28, 2004 2:16 pm
- Location: Guerneville CA
Time to rebuild the touch control?
My touch control is lowering then popping back up. It does this in a continuing cycle. I'm assuming it needs a rebuild. Can I purchase a complete kit somewhere?
Steve Ruddy
Guerneville CA
Guerneville CA
-
- Cub Pro
- Posts: 23701
- Joined: Sun Feb 02, 2003 2:09 pm
- Zip Code: 63664
- Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
- Location: Mo, Potosi
get kit form local dealer, or on line from http://www.cngco.com, possibly form tM tRactor (one of the site sponsers ) also. there are 2 different ones, and you will need the mumber from your TC block.
If you are not part of the solution,
you are part of the problem!!!
you are part of the problem!!!
-
- 10+ Years
- Posts: 187
- Joined: Tue Nov 08, 2005 5:29 pm
- Zip Code: 38370
- Location: TN, Saltillo
I just rebuilt my block Steve. The kit is still available from CASE/IH. As John said there are 2 kits available. The part # on the block found below the fill port is all they need. Mine used the ealier kit and it ran approx. $35 if i remember.
I recomend washing the block really well before tearing into it. And do it in a clean place on a clean surface. And have lotsa rags handy. Be sure to coat all the o-rings with hydraulic oil when re-assembling. I also used a couple cans of brake-cleaner to clean everything real well before installing the new seals and coating with oil. It's hard to get it too clean.
I also recommend getting on the manual server and printing out the parts breakdown for the block you have, this is handy when re-assembling. Be sure to clean everything and keep it clean as you tear it apart. Mine was leaking from the control rod seal and was creeping as you described, now it's stays put and responds alot better.
Russell
I recomend washing the block really well before tearing into it. And do it in a clean place on a clean surface. And have lotsa rags handy. Be sure to coat all the o-rings with hydraulic oil when re-assembling. I also used a couple cans of brake-cleaner to clean everything real well before installing the new seals and coating with oil. It's hard to get it too clean.
I also recommend getting on the manual server and printing out the parts breakdown for the block you have, this is handy when re-assembling. Be sure to clean everything and keep it clean as you tear it apart. Mine was leaking from the control rod seal and was creeping as you described, now it's stays put and responds alot better.
Russell
-
- 10+ Years
- Posts: 178
- Joined: Sat Feb 28, 2004 2:16 pm
- Location: Guerneville CA
-
- Similar Topics
- Replies
- Views
- Last post
-
- 5
- 256
-
by Dale Finch
Tue Jul 18, 2023 9:32 pm
-
- 4
- 269
-
by Bill V in Md
Thu Feb 10, 2022 9:55 pm
-
-
Should this be used with touch control Attachment(s)
by cowridermi » Sun May 14, 2023 2:41 pm » in Farmall Cub - 2
- 234
-
by radioguy41
Sun May 14, 2023 5:07 pm
-
-
- 5
- 1070
-
by Glen
Thu Dec 28, 2023 6:35 pm
-
- 3
- 194
-
by Dale Finch
Sat May 22, 2021 2:38 pm
Who is online
Users browsing this forum: No registered users and 3 guests