This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Clutch pilot tool ?
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 4
- Joined: Sat Mar 29, 2003 10:52 am
- Location: North Carolina
Clutch pilot tool ?
I finally got around to splitting my cub to replace the rear seal in the engine. Thanks to all the tips I read here I discovered that the problem was a new number seal in the old style retainer. When I pulled the flywheel off the seal was sticking out at the bottom and I can R & R with my fingers. I've had the tractor for 15 years before it came loose. I ordered a new style retainer from tm tractor and a new seal from napa. My question is do I need a pilot shaft tool to align the clutch for reassembly or can it be done without it.
-
- Team Cub Guide
- Posts: 3544
- Joined: Sun Feb 02, 2003 6:30 pm
- Zip Code: 38658
- eBay ID: Cub-Bud
- Tractors Owned: Four FCUBs, one IH Lo-Boy, one B Farmall, two Cadets, and a John Deere B.
- Circle of Safety: Y
- Location: MS, Pope
The best bet would be to use a line-up tool. Call John Jr. at JP Tractor Salvage...he'll send you the cut-off end of the clutch shaft for $5-10.
http://www.jptractorsalvage.com/default.htm
http://www.jptractorsalvage.com/default.htm
"Never forget where it is you come from, or you may find yourself someplace you don't want to be"
Greg Norman
Greg Norman
-
- 10+ Years
- Posts: 755
- Joined: Sun Jan 02, 2005 4:28 pm
- Zip Code: 63031
- Location: St. Louis Mo.
Pilot bushing
It makes it a "LOT" easier if you can get a wooden dowel to center the clutch. Shaped to fit as necessary.
-
- 10+ Years
- Posts: 4
- Joined: Sat Mar 29, 2003 10:52 am
- Location: North Carolina
-
- 10+ Years
- Posts: 1055
- Joined: Thu Feb 06, 2003 9:21 am
- Zip Code: 93510
- Location: Acton Ca.
-
- Cub Pro
- Posts: 23701
- Joined: Sun Feb 02, 2003 2:09 pm
- Zip Code: 63664
- Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
- Location: Mo, Potosi
I couldn'r find one that would fit both my pilot bsushing and clutch disk, so for my first time changing a clutch I got a plastic alinement too that fit the pilot and stuck it in a half inch drill and used a grinder to turn down the spline part to slip inside the clutch. Now I have a cut off shaft I use.
If you are not part of the solution,
you are part of the problem!!!
you are part of the problem!!!
-
- Similar Topics
- Replies
- Views
- Last post
-
- 6
- 256
-
by Glen
Tue Jan 03, 2023 11:00 pm
-
- 10
- 406
-
by tst
Thu Apr 13, 2023 8:01 pm
-
- 4
- 175
-
by SamsFarm
Mon Jun 06, 2022 3:35 pm
-
- 15
- 744
-
by Don McCombs
Wed Oct 27, 2021 3:19 pm
-
- 4
- 353
-
by Rmpelley
Tue May 17, 2022 6:28 am
Who is online
Users browsing this forum: Cecil, Dale Finch and 2 guests