This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Back to head scratching about vineyard cultivation
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 484
- Joined: Sun Aug 05, 2012 7:01 am
- Zip Code: 00000
- Tractors Owned: 1955 Cub Fast Hitch
sickle bar
land plow
harrows
snow plow
manure spreader
hayrake, rope pull
variety of cultivators
Wagner WM-1 bucket loader
rear carrier -- homemade - Location: Berkshire hills
Back to head scratching about vineyard cultivation
I'm still hoping for a tractor solution to the work of maintenance of weed-free soil between grape vines. The "Green machine" option looks too expensive, too weighty, too cumbersome for me to even consider it. Extending front cultivator bars to beyond the tractor's wheels on the side seems too much. Mental, half-baked solution? Coming up...but, let me warn you...it is less than even half-baked. Maybe it is still in the mixing bowl....
Here goes. Why not have the sicklebar mounted on the tractor, as I usually do for summertime, but ... (ready for this?)..take the sicklebar off while leaving the under-tractor mount on the tractor. While my sicklebar is off (not putting it on to try it now...I'm doing fence work), I realize that the sicklebar rotates up/down on a pin. So ... remove the pin, take off the entire cutting assembly. Make/design/install another bar of sorts that fits to the under-tractor mount for the sicklebar. I'd have, I think, a bar of my choosing going out the side of the tractor, well beyond the wheels. But a shorter bar than the 4.5' sicklebar. Maybe only 2.5" or 3' ?? If this bar was, say, a chunk of maybe 3" square tubing or whatever ( ! ) that isn't attached to the pitman bar (PTO to be "off"), then it would go up/down by hydraulics, and be constrained fore/aft by the mount. It would ride up over rocks, etc. as does the sicklebar. On the end of this new "bar" would be a means to attach a cultivator tool...say one of those multi-tined jobbies.
Then...I'd be able to come up to a row in the vineyard, keep the Cub in the open grassed walkway, ease this bar/cultivator under the trellis, lower the unit and ease forward, lift up the bar, back up...repeat as needed; move on to the next opening between vines. Not really for removing entrenched weeds (but would it?), but primarily to keep a weeded area maintained. Whattaya think? Got suggestions?
Here goes. Why not have the sicklebar mounted on the tractor, as I usually do for summertime, but ... (ready for this?)..take the sicklebar off while leaving the under-tractor mount on the tractor. While my sicklebar is off (not putting it on to try it now...I'm doing fence work), I realize that the sicklebar rotates up/down on a pin. So ... remove the pin, take off the entire cutting assembly. Make/design/install another bar of sorts that fits to the under-tractor mount for the sicklebar. I'd have, I think, a bar of my choosing going out the side of the tractor, well beyond the wheels. But a shorter bar than the 4.5' sicklebar. Maybe only 2.5" or 3' ?? If this bar was, say, a chunk of maybe 3" square tubing or whatever ( ! ) that isn't attached to the pitman bar (PTO to be "off"), then it would go up/down by hydraulics, and be constrained fore/aft by the mount. It would ride up over rocks, etc. as does the sicklebar. On the end of this new "bar" would be a means to attach a cultivator tool...say one of those multi-tined jobbies.
Then...I'd be able to come up to a row in the vineyard, keep the Cub in the open grassed walkway, ease this bar/cultivator under the trellis, lower the unit and ease forward, lift up the bar, back up...repeat as needed; move on to the next opening between vines. Not really for removing entrenched weeds (but would it?), but primarily to keep a weeded area maintained. Whattaya think? Got suggestions?
-
- 10+ Years
- Posts: 2680
- Joined: Mon Oct 24, 2005 11:35 am
- Zip Code: 14072
- eBay ID: toysforjake
- Tractors Owned: Lots of Cub Cadets!
1951 Farmall Cub
1977 IH Cub
1966 IH Cub
1965 IH Lo Boy
1964 IH Lo Boy
1949 Farmall Cub
Several IH 154 Lo Boys
1979 IH 184 Lo Boy
Simplicity 4416 Sovereign
Simplicity Conquest
Simplicity Legacy 4x4 Diesel
Mitsubishi MT180D 4x4 Diesel - Circle of Safety: Y
- Location: Grand Island, NY
Re: Back to head scratching about vineyard cultivation
I do not think the sickle bar assembley would handle the potential stress of engaging the ground at a point so far away from the mount to the tractor.
The standard cultivators should work fine, you will just need to have the wheels spaced in to the narrowest setting, then only use the far outside cultivator mount. The cultivators are designed to follow just behind, to the outside of the tires (at the narrowest setting) therefore, if you run the tires right down the side of your grapes, the cultivators will dig up and cover those tracks. It should work fine, with no speical fabrication needed. I would run both the front and rear cultivator, just the outside spikes, preferrably on the right side of the tractor, so you can literally watch what you're doing by looking right down the steering wheel at the front tire and front cultivator.
The standard cultivators should work fine, you will just need to have the wheels spaced in to the narrowest setting, then only use the far outside cultivator mount. The cultivators are designed to follow just behind, to the outside of the tires (at the narrowest setting) therefore, if you run the tires right down the side of your grapes, the cultivators will dig up and cover those tracks. It should work fine, with no speical fabrication needed. I would run both the front and rear cultivator, just the outside spikes, preferrably on the right side of the tractor, so you can literally watch what you're doing by looking right down the steering wheel at the front tire and front cultivator.
Cub Cadets 682, 1811, 1864, Simplicity Legacy XL 4x4 Diesel with FEL, 60" mower, 50" Tiller
-
- 10+ Years
- Posts: 1050
- Joined: Tue Apr 26, 2011 10:47 am
- Zip Code: 44266
- Tractors Owned: 48 F Cub #11678
65 Cub Cadet 104
70 450C JD loader
67 Cub Cadet 107
90 B7100HST-D Kubota
72 Cub Cadet 149
54 Super C - Circle of Safety: Y
- Location: Ravenna, Ohio
Re: Back to head scratching about vineyard cultivation
If I understand your idea, you want to mount a conventional cultivator tine or tines to your mower/sickle arm with a bit of extention on it. I think that would put a great deal of lateral stress on on the bolster and the mower bar mounting hardware. The bolster and mower bar mechanism are designed to accomodate some lateral stress but not a huge amount like you would have dragging cultivators through the ground if even for a short distance. A thought I had was to mount some sort of small roto-tiller to your short extention bar that you would need for you cultivator idea. You would want to take off the roto-tiller handle and you could rig a mount for the controlls, maybe half of the original handle bar, so that you could reach them while still on the tractor. I think something like that would work well on the weeds and in the dirt as long as you don't go too fast or too deep. Good luck with you project.
-
- Team Cub Mentor
- Posts: 20379
- Joined: Fri Jul 02, 2004 9:52 pm
- Zip Code: 65051
- Circle of Safety: Y
- Location: Mo. Linn
Re: Back to head scratching about vineyard cultivation
Mowing instead of cultivation? Black walnut plantation and other tree seedlings. I use a weed eater to trim grass and weeds close to seedlings and at each fence post in the fence line around the seedlings. Cub with Mott flail mower to mow between rows of seedlings and under the fence. The flail mower extends about a foot to the right of the tractor tires. Mow slow and weave back and forth to trim/mow around and between seedlings.
A Cub Cadet with hydrostatic transmission works better because of it's tighter turning radius for trimming up close to seedlings.
Still have a bit of hand weeding to do during the weed eater process.
A Cub Cadet with hydrostatic transmission works better because of it's tighter turning radius for trimming up close to seedlings.
Still have a bit of hand weeding to do during the weed eater process.
I have an excuse. CRS.
-
- 10+ Years
- Posts: 807
- Joined: Sat May 07, 2011 8:20 pm
- Zip Code: 27526
- Tractors Owned: 1950 Cub Demo
1978 Cub Cadet 1650
cub 193 plow
cub 174 planter
cub sidedresser
cub 144 cultivator
cadet 50C deck - Circle of Safety: Y
Re: Back to head scratching about vineyard cultivation
Couldnt you use a weed barrier and forego cultivation altogether?
-
- 10+ Years
- Posts: 2929
- Joined: Sun Apr 19, 2009 9:51 pm
- Zip Code: 63664
- Location: MO, Potosi
Re: Back to head scratching about vineyard cultivation
I keep thinking about something similar to the wiggle hoe that TM has a brochure on.
http://www.tm-tractor.com/gbrochures/wiglehoeing.htm
It would have to be mounted to the right side of the tractor instead of behind obviously. Some type of cultivator scratcher (I'm envisioning a multi pronged weed scratcher from an old hand push plow) attached to an arm on a vertical shaft with a lever at the top beside the seat that when you push swings out under the vines. When you come to the stem(?) pull the lever to swing the scratcher back towards the tractor then after the stem push it back out.
The fancier version would have a hydraulically controlled arm like a 4x4 mounted in the same orientation as the sickle bar that would move straight in and out a foot or so under the vines as a lever is moved right or left.
http://www.tm-tractor.com/gbrochures/wiglehoeing.htm
It would have to be mounted to the right side of the tractor instead of behind obviously. Some type of cultivator scratcher (I'm envisioning a multi pronged weed scratcher from an old hand push plow) attached to an arm on a vertical shaft with a lever at the top beside the seat that when you push swings out under the vines. When you come to the stem(?) pull the lever to swing the scratcher back towards the tractor then after the stem push it back out.
The fancier version would have a hydraulically controlled arm like a 4x4 mounted in the same orientation as the sickle bar that would move straight in and out a foot or so under the vines as a lever is moved right or left.
-
- 10+ Years
- Posts: 484
- Joined: Sun Aug 05, 2012 7:01 am
- Zip Code: 00000
- Tractors Owned: 1955 Cub Fast Hitch
sickle bar
land plow
harrows
snow plow
manure spreader
hayrake, rope pull
variety of cultivators
Wagner WM-1 bucket loader
rear carrier -- homemade - Location: Berkshire hills
Re: Back to head scratching about vineyard cultivation
There seems to be a consensus that there will be too much of a lateral force at the tip of any kind of substitute bar coming from the sicklebar mount...if there are tines out there digging into the earth. Too much stress would probably mess up the mount. Getting a tool bar to reach out there would probably have the same issues. Moving the wheels in is something I've not done and would be loath to do it if it messes up settings, takes a great length of time. The idea I was hoping for was one that would allow some "extended side cultivation" for the vineyard as part of a busy summer that has the tractor mostly used for sicklebar work on various hilly, slopes, etc. Resetting wheels, or finding/buying/installing a Green machine are probably well beyond where I want to go.
Thanks for thoughts. I'll be working on them here.
Dick
Thanks for thoughts. I'll be working on them here.
Dick
-
- 10+ Years
- Posts: 12
- Joined: Fri Aug 31, 2012 11:14 am
- Zip Code: 21774
Re: Back to head scratching about vineyard cultivation
Think about running a length of barstock through both 'tool bar clamps' pages 12 and 13, item #4 in the 144 cultivator manual. It could stick out on one or both sides, as you like, and would give you a strong triangulated base for your under the row tool, with the up and down function built in. You could mount your swing back/slide in tiller or teeth. Run it in and out from under the row with a sideways mounted lift handle. ....or something like that
-
- 10+ Years
- Posts: 12
- Joined: Fri Aug 31, 2012 11:14 am
- Zip Code: 21774
Re: Back to head scratching about vineyard cultivation
clodhopper wrote:Couldnt you use a weed barrier and forego cultivation altogether?
I tried weed barriers (long black woven material, water permeable) in a part of my first vineyard. I always ended up chewing a chunk out of it or wrapping it around the mower. Had it stapled down too. Maybe I wasn't doing it right.
-
- 10+ Years
- Posts: 2680
- Joined: Mon Oct 24, 2005 11:35 am
- Zip Code: 14072
- eBay ID: toysforjake
- Tractors Owned: Lots of Cub Cadets!
1951 Farmall Cub
1977 IH Cub
1966 IH Cub
1965 IH Lo Boy
1964 IH Lo Boy
1949 Farmall Cub
Several IH 154 Lo Boys
1979 IH 184 Lo Boy
Simplicity 4416 Sovereign
Simplicity Conquest
Simplicity Legacy 4x4 Diesel
Mitsubishi MT180D 4x4 Diesel - Circle of Safety: Y
- Location: Grand Island, NY
Re: Back to head scratching about vineyard cultivation
Dick,
HWil has a good idea. Using the existing tool bars for the cultivators, you can extend the bar out to one side, far enough to get past your wider wheel spacing. Then you can add a spade or tooth (or two) out there to do your cultivating. Nice, simple application, and should have plenty of strength. You may even be able to leave the sickle mower attached, but I'd have to look closely at where the tool bars come back and where the sickle mower sticks up. It would be close, but worth trying out. Worst case, you can just remove the cutter bar (as you were thinking about originally) and leave the mower mount hooked up.
Give it a try and let us know how you make out. Everyone loves pictures too.
HWil has a good idea. Using the existing tool bars for the cultivators, you can extend the bar out to one side, far enough to get past your wider wheel spacing. Then you can add a spade or tooth (or two) out there to do your cultivating. Nice, simple application, and should have plenty of strength. You may even be able to leave the sickle mower attached, but I'd have to look closely at where the tool bars come back and where the sickle mower sticks up. It would be close, but worth trying out. Worst case, you can just remove the cutter bar (as you were thinking about originally) and leave the mower mount hooked up.
Give it a try and let us know how you make out. Everyone loves pictures too.
Cub Cadets 682, 1811, 1864, Simplicity Legacy XL 4x4 Diesel with FEL, 60" mower, 50" Tiller
-
- 10+ Years
- Posts: 12
- Joined: Fri Aug 31, 2012 11:14 am
- Zip Code: 21774
Re: Back to head scratching about vineyard cultivation
That extended tool bar idea came from Boss Hog the other day during one of our conversations. Howard
-
- 10+ Years
- Posts: 2555
- Joined: Tue Aug 10, 2010 6:38 pm
- Zip Code: 35630
- Circle of Safety: Y
Re: Back to head scratching about vineyard cultivation
I have been talking with a guy up north that bought out several Dealerships in the 80's. He told me he is wanting to sell out all of his parts and implements, and that he has what he calls a "Vineyard Cultivator" for a Farmall Super A - 140 tractor (I think it was....or maybe a Cub). Very Intresting Nonetheless as I haven't ever heard of one.
"
"
Regards,
Chase
205-368-5339
ihfarmallrtr@gmail.com
Follow my page "Alabama Tractor Pickers" on YouTube & Facebook!
Chase
205-368-5339
ihfarmallrtr@gmail.com
Follow my page "Alabama Tractor Pickers" on YouTube & Facebook!
-
- Cub Pro
- Posts: 10540
- Joined: Mon Aug 09, 2004 10:14 pm
- Zip Code: 02840
- Location: RI, Newport
Re: Back to head scratching about vineyard cultivation
There are a lot of vineyards around here these days. I even tried 'will mow for wine' with one place, but they were going to bale the trimmings first. Never heard anything like that before ?? At any rate, they all seem to have turf between the rows and do not seem too critical about what grows between the vines (in the row) in season. That is my 25 MPH observation, which is a passing glance.
Westport River Winery in Westport Mass is owned by the Russell family and they are great folks (best bubbly white in the USA). They also own the Buzzard's Bay brewery (www.justbeer.us). Possibly you could talk to Rob there and get the lowdown on how he cultivates (or doesn't) and why. He has a Cub, but I believe it is used to cultivate something other than vines.
Westport River Winery in Westport Mass is owned by the Russell family and they are great folks (best bubbly white in the USA). They also own the Buzzard's Bay brewery (www.justbeer.us). Possibly you could talk to Rob there and get the lowdown on how he cultivates (or doesn't) and why. He has a Cub, but I believe it is used to cultivate something other than vines.
1971 Cub (Rufus) 1950 Cub (Cathy) 1965 Lo Boy Fast Hitch (Nameless III) 1970 Cub 1000 Loader & Fast Hitch (Lee)
-
- 10+ Years
- Posts: 12
- Joined: Fri Aug 31, 2012 11:14 am
- Zip Code: 21774
Re: Back to head scratching about vineyard cultivation
Might be a couple of reasons to bale the trimmings in the vineyard. Probably #1 is to get them out of the vineyard instead of mowing them, because they harbor the fungal spores that are the bane of humid region grapevines. It'll mean less spraying next year. Another may be to collect sample batches of the cuttings to weigh them which gives you an idea from year to year how the vines are doing and how many buds to leave on for the following year so you don't tax the plant.
You can use the grass in the middles to compete with the vines if they are too vigorous, and cultivate it out if it competes too much. h
You can use the grass in the middles to compete with the vines if they are too vigorous, and cultivate it out if it competes too much. h
-
- 10+ Years
- Posts: 484
- Joined: Sun Aug 05, 2012 7:01 am
- Zip Code: 00000
- Tractors Owned: 1955 Cub Fast Hitch
sickle bar
land plow
harrows
snow plow
manure spreader
hayrake, rope pull
variety of cultivators
Wagner WM-1 bucket loader
rear carrier -- homemade - Location: Berkshire hills
Re: Back to head scratching about vineyard cultivation
HWil wrote:clodhopper wrote:Couldnt you use a weed barrier and forego cultivation altogether?
I tried weed barriers (long black woven material, water permeable) in a part of my first vineyard. I always ended up chewing a chunk out of it or wrapping it around the mower. Had it stapled down too. Maybe I wasn't doing it right.
This seems to be on track. Thanks. Not sure, but I don't think I have that tool bar. Will have to check through what I have. But a tool bar that would go from L to R and extend out beyond the R front wheel and allow attachment of various cultivating tools would be the ticket. Now...There's a plan!
So, if I don't have such a tool bar, then is a long one something that was made? Available? Or do I go to a steel shop and ask them?
-
- Similar Topics
- Replies
- Views
- Last post
-
- 28
- 1055
-
by Don McCombs
Mon Mar 07, 2022 11:09 pm
-
-
Cub cultivation setup has a lot of play in it
by WildFarmall » Mon Feb 28, 2022 11:09 am » in Farmall Cub - 5
- 266
-
by Jim Becker
Tue Mar 01, 2022 9:04 pm
-
-
- 4
- 260
-
by SamsFarm
Thu May 11, 2023 12:32 am
-
-
Back to work for the old gal!! Attachment(s)
by Dale Finch » Sun Sep 26, 2021 11:52 am » in Farmall Cub - 15
- 565
-
by k hutchins
Sat Oct 02, 2021 7:46 pm
-
-
-
Back in the Cub business--kinda. Attachment(s)
by Super A » Mon May 16, 2022 8:44 am » in Farmall Cub - 5
- 291
-
by SamsFarm
Mon May 16, 2022 7:15 pm
-
Who is online
Users browsing this forum: No registered users and 4 guests