I was wondering if there was any special way to set up the 2 bottom plow on a fast hitch like you do for the cub ?
Thanks Rich
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
plow set up on super c with fasthitch
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 79
- Joined: Mon Jan 10, 2011 7:01 pm
- Zip Code: 12578
- Tractors Owned: 1948 Cub w/FH
1948 Cub w/ International 1000 loader
1946 BN
1953 Super C w/FH
1968 John Deere 55 combine
1983 International 1440 - Circle of Safety: Y
- Location: Salt Point N.Y.
-
- 10+ Years
- Posts: 159
- Joined: Sun Apr 07, 2013 10:41 pm
- Zip Code: 47359
- Tractors Owned: Farmall 200
1956 Farmall Cub
1961 Farmall Cub
Farmall 460D
International 656D Hi-Clear
Farmall 806D
Allis Chalmers 5020 - Location: Blackford County, Indiana
Re: plow set up on super c with fasthitch
The Super C Operator's Manual contains instructions for setting up the fast hitch for plowing. The manual is available in PDF manuals on this site.
My 200 has the same hitch. Besides the lift cylinder there are two other hydraulic adjustments. There is a flat bar (leveling link) that connects from the hitch to the left side touch control. I don't have this flat bar for my 200, I think it was probably optional equipment. I recall that this piece is necessary to operate a plow properly. I have seen reproductions of this piece for sale. There is also an adjustable tube (depth-adjusting link) that connects from the right side touch control to the fast hitch bail. This tube can be attached to a fixed point or attached to the touch control in order to raise and lower the front of the bail (much like the depth control adjustment on the Cub).
My 200 has the same hitch. Besides the lift cylinder there are two other hydraulic adjustments. There is a flat bar (leveling link) that connects from the hitch to the left side touch control. I don't have this flat bar for my 200, I think it was probably optional equipment. I recall that this piece is necessary to operate a plow properly. I have seen reproductions of this piece for sale. There is also an adjustable tube (depth-adjusting link) that connects from the right side touch control to the fast hitch bail. This tube can be attached to a fixed point or attached to the touch control in order to raise and lower the front of the bail (much like the depth control adjustment on the Cub).
-
- Team Cub
- Posts: 17288
- Joined: Sun Feb 02, 2003 2:59 pm
- Zip Code: 55319
- Circle of Safety: Y
- Location: MN
Re: plow set up on super c with fasthitch
Xperimental wrote:I think it was probablyoptional equipmentmisplaced by a PO.
-
- 10+ Years
- Posts: 79
- Joined: Mon Jan 10, 2011 7:01 pm
- Zip Code: 12578
- Tractors Owned: 1948 Cub w/FH
1948 Cub w/ International 1000 loader
1946 BN
1953 Super C w/FH
1968 John Deere 55 combine
1983 International 1440 - Circle of Safety: Y
- Location: Salt Point N.Y.
Re: plow set up on super c with fasthitch
Thank you for the help
Rich
Rich
-
- 10+ Years
- Posts: 4953
- Joined: Tue Jun 08, 2004 3:04 pm
- Zip Code: 14559
- Circle of Safety: Y
- Location: Rochester, NY
Re: plow set up on super c with fasthitch
The front adjustment is for the depth control same as a Cub.
The left side adjustment is to level the plow when the right wheel is in the furrow.
Basically you need to set the tread width on the rear wheels so the front bottom takes a full cut while the right rear wheel is somewhere in the furrow. IIRC there's a mathematical formula for this. Then, you adjust the plow depth for your desired depth, and then level the plow side-to-side so it's leaving a level furrow behind you.
The left side adjustment is to level the plow when the right wheel is in the furrow.
Basically you need to set the tread width on the rear wheels so the front bottom takes a full cut while the right rear wheel is somewhere in the furrow. IIRC there's a mathematical formula for this. Then, you adjust the plow depth for your desired depth, and then level the plow side-to-side so it's leaving a level furrow behind you.
-
- Similar Topics
- Replies
- Views
- Last post
-
- 24
- 5518
-
by Magnum
Mon Jan 23, 2023 11:03 pm
-
-
Super C Steps and 3pt Attachment(s)
by ajhbike » Thu Dec 28, 2023 4:44 pm » in Farmall C, Super C, 200 & 230 - 5
- 856
-
by ajhbike
Thu Dec 28, 2023 7:07 pm
-
-
- 5
- 1443
-
by MD200460
Tue Oct 04, 2022 2:47 pm
-
- 3
- 966
-
by ajhbike
Tue Aug 30, 2022 6:05 pm
-
- 1
- 1144
-
by Eugene
Fri Nov 19, 2021 9:52 pm
Return to “Farmall C, Super C, 200 & 230”
Who is online
Users browsing this forum: No registered users and 0 guests