This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Paint prep question?
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 185
- Joined: Thu Jul 08, 2004 6:00 pm
Paint prep question?
Looking to paint the hood/gas tank on my Cub this winter. This is not a show tractor, just a working one but want to protect it. Paint is in poor condition and metal is somewhat rough or pitted. Not too bad but not like your cars fenders. So how do I get the metal smooth. Will sand off the paint to the bare metal. So do I keep sanding til smooth or at some point smather on some sort of filler and sand it smooth?
Going to rattle can it, prime and color. To get the proper red, do I just use the cans from IH dealer or is there a cheaper brand that would do me just as good. Top coat the paint with anything? Thanks guys.
Going to rattle can it, prime and color. To get the proper red, do I just use the cans from IH dealer or is there a cheaper brand that would do me just as good. Top coat the paint with anything? Thanks guys.
-
- 10+ Years
- Posts: 807
- Joined: Sat May 07, 2011 8:20 pm
- Zip Code: 27526
- Tractors Owned: 1950 Cub Demo
1978 Cub Cadet 1650
cub 193 plow
cub 174 planter
cub sidedresser
cub 144 cultivator
cadet 50C deck - Circle of Safety: Y
Re: Paint prep question?
After cleaning to bare metal, use a brush in a drill to remove any rust down in the pitting, wipe it down good with laquer thinner, and depending on how bad the pitting is, I would use either filler, or a primer putty.
-
- 10+ Years
- Posts: 438
- Joined: Tue Aug 07, 2012 1:37 am
- Zip Code: 44134
- Tractors Owned: 1949 & 1951 Farmall Cubs
Several Snapper Garden Tractors - Circle of Safety: Y
- Location: Southern Suburbs of Cleveland, Ohio
Re: Paint prep question?
You will get many responses, my choice would be to prepare the metal as you described, spot putty from a tube, sand, prime, repeat until you are satisfied with the finish.
Prepare the surface then use Majic brand IHC red from TSC.
I've had awesome results with the Majic brand, nearly as good as a hvlp prayer.
Of course the better prepared the surface, the better the finish job.
Prepare the surface then use Majic brand IHC red from TSC.
I've had awesome results with the Majic brand, nearly as good as a hvlp prayer.
Of course the better prepared the surface, the better the finish job.
- Attachments
-
- 1351132570-picsay.jpg (42.38 KiB) Viewed 732 times
"HAVE ALL YOUR DELIVERIES MADE BY UNION DRIVERS"
-
- Cub Pro
- Posts: 5238
- Joined: Sat Sep 08, 2007 3:49 pm
- Zip Code: 25271
- eBay ID: yogiefisher
- Tractors Owned: 37 John Deere A
63 Farmall Cub
53 Farmall Cub
56 Farmall Cub
IH 140
Massey 165 & 250 - Circle of Safety: Y
- Location: WV. Ripley
Re: Paint prep question?
I like the spot putty in the tube, kind of a finishing filler. I use it all the time, sands much eaiser than Bondo filler.
Usually needs a little extra time to dry...
Usually needs a little extra time to dry...
Democracy is two wolves and a lamb voting on what to have for lunch. Liberty is a well-armed lamb contesting the vote.
Ben Franklin
-
- 10+ Years
- Posts: 438
- Joined: Tue Aug 07, 2012 1:37 am
- Zip Code: 44134
- Tractors Owned: 1949 & 1951 Farmall Cubs
Several Snapper Garden Tractors - Circle of Safety: Y
- Location: Southern Suburbs of Cleveland, Ohio
Re: Paint prep question?
Yogie wrote:sands much eaiser than Bondo filler.
Can say that again and also finishes the surface just as well with less effort and less sanding media.
"HAVE ALL YOUR DELIVERIES MADE BY UNION DRIVERS"
-
- 10+ Years
- Posts: 438
- Joined: Tue Aug 07, 2012 1:37 am
- Zip Code: 44134
- Tractors Owned: 1949 & 1951 Farmall Cubs
Several Snapper Garden Tractors - Circle of Safety: Y
- Location: Southern Suburbs of Cleveland, Ohio
Re: Paint prep question?
Less than 6 bucks a can at TSC. Takes 24 hours plus to dry in ideal conditions.
- Attachments
-
- Part # 8-22972 IH Red
- 1351133904-picsay.jpg (43.45 KiB) Viewed 724 times
"HAVE ALL YOUR DELIVERIES MADE BY UNION DRIVERS"
-
- Team Cub Mentor
- Posts: 17520
- Joined: Mon Feb 03, 2003 6:45 am
- Zip Code: 21550
- Tractors Owned: "1950 Something" Farmall Cub
1957 Farmall Cub w/FH
1977 International Cub w/FH
1978 International Cub
1948 Farmall Super A - Circle of Safety: Y
- Location: MD, Deep Creek Lake
Re: Paint prep question?
More information on the spot putty, please.
-
- 10+ Years
- Posts: 908
- Joined: Sat Feb 15, 2003 7:20 am
- Zip Code: 00000
Re: Paint prep question?
I’m not a professional painter; I’ve done a lot of painting and have been around a lot of professional auto body people. They always told me the biggest problem with spot putty is that after application it’s not allowed to set long enough for it to shrink before putting primer or paint over it.
I use it all the time for small imperfections and properly used it works great.
I use it all the time for small imperfections and properly used it works great.
-
- 10+ Years
- Posts: 807
- Joined: Sat May 07, 2011 8:20 pm
- Zip Code: 27526
- Tractors Owned: 1950 Cub Demo
1978 Cub Cadet 1650
cub 193 plow
cub 174 planter
cub sidedresser
cub 144 cultivator
cadet 50C deck - Circle of Safety: Y
Re: Paint prep question?
Don McCombs wrote:More information on the spot putty, please.
Spot putty is basically a primer that is thick enough to spread on. It does not require any activators or resins, you just squeeze it out like toothpaste and spread it on, HOWEVER, it is only used to fill small imperfections and must be applied only in thin coats. The bigggest problem people have with spot putty is trying to use it as a filler, which it was not designed to be, and if put on thick, it will never dry.
-
- 10+ Years
- Posts: 438
- Joined: Tue Aug 07, 2012 1:37 am
- Zip Code: 44134
- Tractors Owned: 1949 & 1951 Farmall Cubs
Several Snapper Garden Tractors - Circle of Safety: Y
- Location: Southern Suburbs of Cleveland, Ohio
Re: Paint prep question?
Don McCombs wrote:More information on the spot putty, please.
Spot putty comes out of the tube ready to use. It has the consistency of toothpaste and is intended to fill minor surface imperfections not holes or large dings.
It unlike catalyst bound fillers requires overnight drying for best results making standard fillers more economical for the body and finishing industry due to rapid drying time.
The stuff works great as long as you allow the time for it to completely dry before sanding or finishing.
There is nothing fast about bodywork, those jobs rushed indicated by the results. If you are familiar with drywall filling or joint compound, drying time is the same.
"HAVE ALL YOUR DELIVERIES MADE BY UNION DRIVERS"
-
- 10+ Years
- Posts: 4954
- Joined: Tue Jun 08, 2004 3:04 pm
- Zip Code: 14559
- Circle of Safety: Y
- Location: Rochester, NY
Re: Paint prep question?
You can get spot putty in the automotive section of walmart. Look for the product on a squatty-looking metal toothpaste tube.
-
- 10+ Years
- Posts: 6694
- Joined: Tue Apr 27, 2010 11:34 am
- Zip Code: 27517
- Tractors Owned: '51 Cub #140966 "Bruno" with Woods 59 mower
'55 Cub #187541 "Betty" with Fast Hitch
'55 Cub #190482 "Ben" with Woods 42 mower
'55 Cub #191739 "Bertha" with Woods 42 mower
'56 Cub #194370 "Boris" with Mott Flail mower - Circle of Safety: Y
- Location: NC, Chapel Hill
Re: Paint prep question?
Since I was fortunate enough to do my SA restoration at a paint and body shop, I saw and took advantage of a lot of their expertise. They helped me with the selection of filler and primers, which included regular body filler (2 part like Bondo), spot filler (only for real small spots or scratches), and high build primer (which allowed me to do a fair amount of sanding to get the sandblasting roughness and scratches that remained out).
Here is one reference that I Googled that might help with some information.
http://www.mig-welding.co.uk/primer.htm
Please be aware that I am NOT a body/paint person...just kept my eyes open and asked questions. One real factor in all of the painting was if you want the finished paint smooth, you MUST have a smooth primer finish...the paint will NOT fill any holes or rough surface. Also, sand between any dry paint coats. (Prep work: 90% of the job, Painting: 10%!!)
Good luck, and I hope a real painter comes along with better info!! I'm sure you will do fine.
Here is one reference that I Googled that might help with some information.
http://www.mig-welding.co.uk/primer.htm
Please be aware that I am NOT a body/paint person...just kept my eyes open and asked questions. One real factor in all of the painting was if you want the finished paint smooth, you MUST have a smooth primer finish...the paint will NOT fill any holes or rough surface. Also, sand between any dry paint coats. (Prep work: 90% of the job, Painting: 10%!!)
Good luck, and I hope a real painter comes along with better info!! I'm sure you will do fine.
-
- 10+ Years
- Posts: 908
- Joined: Sat Feb 15, 2003 7:20 am
- Zip Code: 00000
Re: Paint prep question?
You're right the best finish is smooth primer, sanding between paint coats and the finish will be like a mirror and very deep looking. You can sand between paint coats on the Acrylic and Urethane paints but on the Alkaline enamel paints (IH Iron guard, Van Sickle, Majic and ect.) you have to let set (cure) for a period of time.
Because of the hazards of the Urethane paints I’ve been priming with sandable primer and painting with Alkaline enamel paints. After a period of time I buff the last coat with Urethane paint buffing compound.
You’re fortunate to be working with a body shop.
Because of the hazards of the Urethane paints I’ve been priming with sandable primer and painting with Alkaline enamel paints. After a period of time I buff the last coat with Urethane paint buffing compound.
You’re fortunate to be working with a body shop.
-
- 10+ Years
- Posts: 99
- Joined: Tue Feb 21, 2012 11:02 pm
- Zip Code: 19520
- Tractors Owned: 1948 Farmall Cub
2007 Cub Cadet
Re: Paint prep question?
I've done a lot of paint work. If the tractor has all original paint, it can be fairly simple. Wet sand with 220 wet sandpaper and use a lot of water. Goal is smooth, not stripped. Think of the old paint as a filler.
Grind dents and rust to bare metal. Fill those spots with Bondo, then sand with 36, then 80 grit. Prime with a laquer primer, building it with 2 or 3 coats. It dries fast. Sand all with 320 wet until baby smooth. Run your palm across the surface. If you feel it, you will see it. This is where the difference between 'real nice' and 'just shiny' is. If you're not happy, fill again if necessary, repeat priming and sanding until satisfied. Use Putty only when filling very small imperfections - less than 1/16th inch thick. Putty adheres best to primer, not metal. Paint with a single stage urethane paint. Shopline is reasonably priced. You can use enamel, but once you do, prepared to be happy with it because repairing enamel is much more difficult than repairing urethane or laquer.
I've helped a lot of those kids who like to spray paint their cars, and in each case they learn the hard way how hard it is to fix the mess they've made with Krylon.
Grind dents and rust to bare metal. Fill those spots with Bondo, then sand with 36, then 80 grit. Prime with a laquer primer, building it with 2 or 3 coats. It dries fast. Sand all with 320 wet until baby smooth. Run your palm across the surface. If you feel it, you will see it. This is where the difference between 'real nice' and 'just shiny' is. If you're not happy, fill again if necessary, repeat priming and sanding until satisfied. Use Putty only when filling very small imperfections - less than 1/16th inch thick. Putty adheres best to primer, not metal. Paint with a single stage urethane paint. Shopline is reasonably priced. You can use enamel, but once you do, prepared to be happy with it because repairing enamel is much more difficult than repairing urethane or laquer.
I've helped a lot of those kids who like to spray paint their cars, and in each case they learn the hard way how hard it is to fix the mess they've made with Krylon.
-
- 10+ Years
- Posts: 7153
- Joined: Sat Feb 18, 2006 8:12 pm
- Zip Code: 15101
- eBay ID: lacrosseorgans
- Skype Name: Mike.Hengelsberg
- Tractors Owned: 1949 Cub "Merlin"
1955 Cub "Lewis"
Cub Trailer
A-60 Blade
Cub-22 Mower
193 Plow - Circle of Safety: Y
- Location: PA, Allison Park (Am Hengelsberg)
Re: Paint prep question?
L U D... You mentioned that you really liked Majic Paint. I have heard several folks on here really complaining that it is not nearly as nice as the old paint from TSC or from IH. Most said that they didn't like the fact that the paint took so long to dry and cure and that it did not like to cover as well as the old stuff...
I'd like to hear more about your experiences as I am going to be going through just this same path soon with Lewis, piece by piece...
I'd like to hear more about your experiences as I am going to be going through just this same path soon with Lewis, piece by piece...
-
- Similar Topics
- Replies
- Views
- Last post
-
- 17
- 485
-
by Glen
Wed Aug 18, 2021 1:25 am
-
- 3
- 275
-
by AL Farmall Boy
Wed Mar 06, 2024 12:14 pm
-
- 4
- 218
-
by Don McCombs
Fri Feb 16, 2024 10:54 am
-
- 6
- 224
-
by Gary Dotson
Tue Aug 01, 2023 7:30 am
-
- 4
- 354
-
by ShawnAgne
Fri Nov 05, 2021 6:07 pm
Who is online
Users browsing this forum: No registered users and 1 guest