Farmall Cub Forum -- Questions and answers to all of your Cub related issues.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds
or one of our site sponsors for your tractor and parts needs.
Thu Nov 08, 2012 7:37 pm
hey guys have a 1954 farmall cub getting tractor cleaned and ready to paint i noticed the air filter cup where you put oil in cup half of gasket is gone called dealer to try to order new gasket says not available what should i do make a gasket out of some kind of cork ? or use some kind of gasket sealer Thanks for any help
Thu Nov 08, 2012 7:45 pm
If you're talking about this cup, there is no gasket required. If you have part of one, the previous owner may have added it. picture from TM Tractor
Thu Nov 08, 2012 8:24 pm
No gasket on mine either .
Thu Nov 08, 2012 8:39 pm
The oil should be thick enough to get the dust and dirt stick to it. There is not enough in there for it to slosh around with that baffle cup in the bottom.
Thu Nov 08, 2012 10:04 pm
IT SHOULD HAVE A GASKET ON IT THE GASKET STATES UP IN AIR CLEANER-------
--GET A MIRROR AND YOU CAN SEE IT UP IN AIR CLEANER------ THAT KEEPS IT FROM
SUCKING DIRTY AIR----I WOULD MAKE ONE AND PUT RUBBER CEMENT ON TOP SIDE
AND STICK IT UP IN AIR CLEANER-------
MY $0.08--- OK---
Thu Nov 08, 2012 10:22 pm
Lombard, I don't see any gasket shown on this parts page.
Thu Nov 08, 2012 10:28 pm
i agree with lombard , my 2 cubs had gaskets on the air cleaner.
Thu Nov 08, 2012 10:43 pm
I have never seen a gasket on one
Thu Nov 08, 2012 10:48 pm
The oil goes in part 9 not part #7.
Bob McCarty;s photo is Part #9 held up tight underneath by the bail and
there is no gasket to my knowledge.
Thu Nov 08, 2012 11:24 pm
lombard wrote:IT SHOULD HAVE A GASKET ON IT THE GASKET STATES UP IN AIR ....
Rob in NH wrote:i agree with lombard , my 2 cubs had gaskets on the air cleaner.
There is no gasket on the oil cup. Any that you may have seen was added by a previous owner.
Any air/dirt that may be pulled in the joint will still be drawn up through the oil soaked mesh before it gets to the carb.
Fri Nov 09, 2012 6:42 am
it wasn't on the cup,it was on the air cleaner.
Fri Nov 09, 2012 8:27 am
Three cubs - n gasket.
Fri Nov 09, 2012 8:36 am
Owning two tractors with Donaldson air cleaners, both with seemingly factory installed, well adhered fiber gaskets, it is impossible to believe no gasket was ever produced or installed even though the parts manuals clearly indicate no gasket or seal should be present.
Too many tractors have these gaskets to assume they were field installations by previous owners, especially since they fit perfectly.
I have a theory this fiber like substance may have been a spray coating applied to the lip of the filter can at the time of manufacture, therefore not otherwise indicated in parts breakdowns.
Edit for spelling error...
- Fiber Seal on Underside of Air Cleaner Can
- 1352466746-picsay.jpg (53.73 KiB) Viewed 458 times
Last edited by lazyuniondriver
on Fri Nov 09, 2012 9:29 am, edited 1 time in total.
Fri Nov 09, 2012 8:41 am
thats the gasket that mine have, thanks uniondriver, i'm not losing it.
Fri Nov 09, 2012 1:20 pm
I pulled off 5 this morning, 3 had no "gasket", 2 did.
I checked a 6th that wasn't on a tractor, and it had a very clean metal surface. I'll admit that I didn't know there was one there, but it doesn't look like they were on all the oil baths. Maybe different suppliers? If you think it's needed, a thin O-ring might be an easier solution than trying to cut something to fit.
Powered by phpBB © phpBB Group.
phpBB Mobile / SEO by Artodia.