Did a couple rebuilds this weekend on some Cub Hydraulic Pumps. One of which is the early style with the actual oil seal instead of the o-ring. Upon cleaning up the outside of the pump I noticed that under the red paint, it had Federal Yellow on it too. I thought the pumps with the oil seals were early pumps (late 40's - early 50's)??
2nd Question......I looked at TM Tractors site since the oil seal wasn't included with their rebuild kit; but didn't see that it was offered on their site. I've also tried searching the part number off the old seal on a couple parts stores sites, but no help. Where would I find the correct seal for the pump. Here is the old seal that came out......
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Oil Seal for Hyd. Pump - Early Style
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 2558
- Joined: Tue Aug 10, 2010 6:38 pm
- Zip Code: 35630
- Circle of Safety: Y
Oil Seal for Hyd. Pump - Early Style
Regards,
Chase
205-368-5339
ihfarmallrtr@gmail.com
Follow my page "Alabama Tractor Pickers" on YouTube & Facebook!
Chase
205-368-5339
ihfarmallrtr@gmail.com
Follow my page "Alabama Tractor Pickers" on YouTube & Facebook!
-
- 10+ Years
- Posts: 2558
- Joined: Tue Aug 10, 2010 6:38 pm
- Zip Code: 35630
- Circle of Safety: Y
Re: Oil Seal for Hyd. Pump - Early Style
And here are some pictures of the entire assembly as I took it apart and discovered it was the oil seal type. I decided to not go any further until I got the correct seal and could finish it.
Regards,
Chase
205-368-5339
ihfarmallrtr@gmail.com
Follow my page "Alabama Tractor Pickers" on YouTube & Facebook!
Chase
205-368-5339
ihfarmallrtr@gmail.com
Follow my page "Alabama Tractor Pickers" on YouTube & Facebook!
-
- 10+ Years
- Posts: 203
- Joined: Thu Sep 29, 2011 3:17 pm
- Zip Code: 48180
- Tractors Owned: 1952 Cub with
- 54 Blade
- 193 Moldboard Plow
- Woods 59 C-2 mower
Re: Oil Seal for Hyd. Pump - Early Style
Case/IH part number 355 742 R91, or National 471526.
Where you are, right now, is of absolutly no use unless you are able to get away from it, FAST!
-
- 10+ Years
- Posts: 2558
- Joined: Tue Aug 10, 2010 6:38 pm
- Zip Code: 35630
- Circle of Safety: Y
Re: Oil Seal for Hyd. Pump - Early Style
Thanks much! The National should suffice to get a parts store to look it up.
Regards,
Chase
205-368-5339
ihfarmallrtr@gmail.com
Follow my page "Alabama Tractor Pickers" on YouTube & Facebook!
Chase
205-368-5339
ihfarmallrtr@gmail.com
Follow my page "Alabama Tractor Pickers" on YouTube & Facebook!
-
- Cub Pro
- Posts: 23701
- Joined: Sun Feb 02, 2003 2:09 pm
- Zip Code: 63664
- Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
- Location: Mo, Potosi
Re: Oil Seal for Hyd. Pump - Early Style
The nice thing about that seal is that it is quite a bit thinner than the original, so you can install it shallower so the lip does not ride in the shaft groove cut by the old one.
If you are not part of the solution,
you are part of the problem!!!
you are part of the problem!!!
-
- 10+ Years
- Posts: 2558
- Joined: Tue Aug 10, 2010 6:38 pm
- Zip Code: 35630
- Circle of Safety: Y
Re: Oil Seal for Hyd. Pump - Early Style
Yes, I was reading in your older posts where you had mentioned that. That is a good thing. This particular shaft isn't as worn as the shaft was that had the "o-ring" style seal. The shaft that had the o-ring seal had a groove cut in it and was a little rough, so I smoothed it down with some 600 grit paper. Hopefully it will be fine, as everything is good and tight after putting it back together. This particular pump wasn't in as bad of shape. It only had a small indenture where the seal lip was riding and wasn't rough at all. All-in-all, it should be like a new pump once I'm done with it.
Thanks again for the help and information guys! I think I'm gonna tackle a rebuild of the touch control next, as well as each for a Farmall 140!! (fingers crossed)
Thanks again for the help and information guys! I think I'm gonna tackle a rebuild of the touch control next, as well as each for a Farmall 140!! (fingers crossed)
Regards,
Chase
205-368-5339
ihfarmallrtr@gmail.com
Follow my page "Alabama Tractor Pickers" on YouTube & Facebook!
Chase
205-368-5339
ihfarmallrtr@gmail.com
Follow my page "Alabama Tractor Pickers" on YouTube & Facebook!
-
- Similar Topics
- Replies
- Views
- Last post
-
- 2
- 218
-
by 1953vacub
Tue Mar 28, 2023 8:37 am
-
- 3
- 277
-
by Super A
Fri Jun 11, 2021 9:34 am
-
- 1
- 149
-
by tst
Thu Feb 22, 2024 1:07 am
-
-
Early Christmas gifts for my cubs! Attachment(s)
by Dale Finch » Mon Sep 13, 2021 2:48 pm » in Farmall Cub - 9
- 436
-
by indy61
Tue Sep 14, 2021 2:36 pm
-
-
-
Early engine block change to strenghen break prone front ear
by staninlowerAL » Thu Dec 16, 2021 10:24 am » in Farmall Cub - 2
- 366
-
by radioguy41
Fri Dec 17, 2021 6:54 am
-
Who is online
Users browsing this forum: No registered users and 9 guests