I was in need of something to do the heavy lifting round here. I decided I needed a boom pole, but wanted it independent of the hydraulics. I also wanted to be able to leave the mower hooked up, and I wanted it out front, for more accuracy in loading and unloading heavy parts and implements.
That does not leave a lot of options for the front of the cub. So, I started looking around and started to get an idea. I engineer better with my hands than with a pencil, so I dug in.
I have 4 grader blades hanging around here, so I snagged one of them and mounted it. I then removed the plow blade. Next I knew I would need some strength(and did not want to use the hydraulics). The cub I used is set wide for stability. So, I took a length of chain, wrapped the axle a couple times and slid it through the brackets under the plow frame to the other side. Basically making a sling to hold the unit up. The axle still pivots as the chain slides when needed.
Next I made 2 brackets that slide over the ends of a small 3pt boom pole I had, and pinned them in holes where the blade was. I had another bar that bolts into the center link and fastens to the brace of the plow frame that bolts to the torque tube. This fastens and positions the boom pole where i wanted it.
Lastly, A long time ago I bought a couple 2000lb winches from TSC for $50 ea. I mounted a new one under the floor and ran the cables to a pulley system at the end.
It works great. I lifted a half dozen implements and put them on a trailer this afternoon. I easily picked up sets of rear weights and stacked them on the trailer. Lastly here is a picture of the lift with the front end of a 23A disc in the air. This is going to save me a lot of work. I had everything laying around, even the winch. Total cost $50 for the winch.
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
building a cub boom pole on a budget
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
building a cub boom pole on a budget
- Attachments
-
- 20130309_164001.jpg (87.58 KiB) Viewed 2439 times
-
- 20130309_163933.jpg (79.27 KiB) Viewed 2439 times
-
- 20130309_163913.jpg (90.34 KiB) Viewed 2439 times
-
- 20130309_163823.jpg (77.27 KiB) Viewed 2439 times
-
- 10+ Years
- Posts: 133
- Joined: Fri Sep 02, 2011 6:22 pm
- Zip Code: 33876
Re: building a cub boom pole on a budget
Dale ,
That looks handy for sure. I would like to see it .
That looks handy for sure. I would like to see it .
-
- 10+ Years
- Posts: 6338
- Joined: Wed Sep 12, 2007 8:40 pm
- Zip Code: 49120
- Circle of Safety: Y
- Location: Niles / Buchanan, Michigan
Re: building a cub boom pole on a budget
That is too cool!! That took some thinking.
Is the Cub and winch12v.?? I like the way you've got it set up with the boom stationary and the winch routed through the boom pulley doing the lifting. Great idea!!
Thanks for sharing.
Is the Cub and winch12v.?? I like the way you've got it set up with the boom stationary and the winch routed through the boom pulley doing the lifting. Great idea!!
Thanks for sharing.
1929 Farmall Regular
1935 John Deere B
1937 John Deere A
1941 John Deere H
1952 John Deere B
1953 Farmall Cub
1935 John Deere B
1937 John Deere A
1941 John Deere H
1952 John Deere B
1953 Farmall Cub
-
- 10+ Years
Re: building a cub boom pole on a budget
yes Ricky, the cub and the winch are 12v. I knew that I would have an easier time lifting using multiple pullies, I can simply unhook the end hook if I need a little more reach.
It is a simple 2000lv 12v winch from TSC, the battery I use in the cub is just a 250 CCA garden tractor battery. It lifted the pairs of wheel weights with no problem, and as you can see in the picture, it is easily lifting and holding the 1/2 of the 23A disc.
It is a simple 2000lv 12v winch from TSC, the battery I use in the cub is just a 250 CCA garden tractor battery. It lifted the pairs of wheel weights with no problem, and as you can see in the picture, it is easily lifting and holding the 1/2 of the 23A disc.
-
- 10+ Years
- Posts: 1655
- Joined: Thu Dec 24, 2009 9:19 am
- Zip Code: 00000
- Tractors Owned: '48 trimmed dash high crop cub , '78 3/4 cub , lo-boy/59 mower , '64 "galvanized" cub , cub-6 toolbar , sicklebar mowers , 54 blade , plow , mott mower , early belly mower . . international 1010 pickup with 345ci v-8 .
- Circle of Safety: Y
- Location: louisiana
Re: building a cub boom pole on a budget
dale , that is as slick as it gets . we are quickly losing those salt of the earth guys with the talent and experience to "make do" with what you have . hats off to you , sir . coppersmythe..........................
-
- 10+ Years
Re: building a cub boom pole on a budget
LOL Val, read the tag line at the bottom of my post.
-
- 10+ Years
- Posts: 1655
- Joined: Thu Dec 24, 2009 9:19 am
- Zip Code: 00000
- Tractors Owned: '48 trimmed dash high crop cub , '78 3/4 cub , lo-boy/59 mower , '64 "galvanized" cub , cub-6 toolbar , sicklebar mowers , 54 blade , plow , mott mower , early belly mower . . international 1010 pickup with 345ci v-8 .
- Circle of Safety: Y
- Location: louisiana
Re: building a cub boom pole on a budget
dale , how many times i must have seen that and never really read it not bad , not bad at all , coppersmythe...................................
-
- 10+ Years
- Posts: 358
- Joined: Thu Jun 30, 2011 9:19 pm
- Zip Code: 32327
- Tractors Owned: Now
73 MF 165
63 MF 203 Ind
44 BF Avery "A" Project
51 Farmall Cub
49 Farmall Cub
48 Farmall Super A - Circle of Safety: Y
- Location: Crawfordville, Fla
Re: building a cub boom pole on a budget
That will sure help you out Dale. Makes it alot easier on the back as well, we ain't gettin any younger.
"Work smarter; Not harder"
-
- Cub Pro
- Posts: 1906
- Joined: Tue Jan 18, 2011 9:16 am
- Zip Code: 72940
- Tractors Owned: 1951 Farmall Cub, 152 disk plow, 2 gang disk, belly mower, sickle mower
1949 Farmall Cub, cultivator, moldboard plow, disk,front blade. Cub Cadet, LTX1045 Mower. Cub Cadet's 109, 125, 1000, and 1250
1961 cub c2 belly mower and full blade. 48 cub manual lift with cultivators.
1947 Cub - Circle of Safety: Y
- Location: Huntington, AR
Re: building a cub boom pole on a budget
Good work, that should give the old back some rest.
-
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger - Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
Re: building a cub boom pole on a budget
Dale:
A rather interesting take on using what you have to ease the strain on the back. Interesting idea ..
A rather interesting take on using what you have to ease the strain on the back. Interesting idea ..
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship
-
- 10+ Years
Re: building a cub boom pole on a budget
We just got a couple inches of rain. Time to see how it will do pulling old fence posts while the ground is soft.
-
- Similar Topics
- Replies
- Views
- Last post
-
- 5
- 207
-
by inairam
Sun May 28, 2023 6:12 pm
Who is online
Users browsing this forum: CharlieK, Majestic-12 [Bot] and 4 guests