Hey yall, I ordered my oil seal and crank pulley wear sleeve today, suppose to be in tomorrow morning. I read some where on here that the sleeve has a tapered end and flat end. Which end goes in towards the block? I was guessing the tapered end? Supposedly the wear sleeve I ordered from NAPA comes with the installation tool. I am planning on installing the sleeve on the Pulley while I am on lunch tomorrow at work, (I work at my local John Deere dealer). Thanks for pointing me in the right direction,
Craig
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Crank pulley Wear Sleeve Install
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 140
- Joined: Fri Jan 31, 2014 7:52 pm
- Zip Code: 28430
-
- Team Cub
- Posts: 11862
- Joined: Tue May 25, 2004 8:02 pm
- Zip Code: 80501
- Tractors Owned: Cubs, MH Pony, Shaw, Allis G, 1934 Silver King, JD LA and LI, Gibson D, David Bradley Tri-Trac
- Circle of Safety: Y
- Location: CO, Longmont
Re: Crank pulley Wear Sleeve Install
If it comes with the installation sleeve, one end will have a lip that the tool seats against. The lip will have a score around it. After installation, you can remove the lip with a pair of side cutters. You are correct that the taper will go towards the block to facilitate the sleeve slipping through the seal.
Bob
Bob
"We don't need to think more,
we need to think differently."
-Albert Einstein
we need to think differently."
-Albert Einstein
-
- 10+ Years
- Posts: 140
- Joined: Fri Jan 31, 2014 7:52 pm
- Zip Code: 28430
Re: Crank pulley Wear Sleeve Install
Bob, so to clearify the lip end will go onto the pulley first right? I ordered wear sleeve # 99193 the day before yesterday and got it today and It was wrong, too big, I got the napa guy to look up what is suppose to be the right one today, will post #s later..
Thanks Craig
Thanks Craig
-
- Team Cub
- Posts: 11862
- Joined: Tue May 25, 2004 8:02 pm
- Zip Code: 80501
- Tractors Owned: Cubs, MH Pony, Shaw, Allis G, 1934 Silver King, JD LA and LI, Gibson D, David Bradley Tri-Trac
- Circle of Safety: Y
- Location: CO, Longmont
Re: Crank pulley Wear Sleeve Install
Yes, The seating tool rests against that lip so you can drive it onto the shaft. Here's a link to a video slide show that Raymond and I did with a differential shaft sleeve. It's a little different than what you are doing but shows one style of seating tool, the lip, and removal of the lip at the end: viewtopic.php?f=54&t=66493
Bob
Bob
"We don't need to think more,
we need to think differently."
-Albert Einstein
we need to think differently."
-Albert Einstein
-
- 10+ Years
- Posts: 807
- Joined: Sat May 07, 2011 8:20 pm
- Zip Code: 27526
- Tractors Owned: 1950 Cub Demo
1978 Cub Cadet 1650
cub 193 plow
cub 174 planter
cub sidedresser
cub 144 cultivator
cadet 50C deck - Circle of Safety: Y
Re: Crank pulley Wear Sleeve Install
When i did mine, I put the sleeve in boiing water for about 15 minutes before installing. Made a big difference to ease installation. Make sure to wear gloves though.
-
- Similar Topics
- Replies
- Views
- Last post
-
- 3
- 279
-
by john2189
Wed Jun 23, 2021 8:41 am
-
- 0
- 137
-
by Scott 1234
Tue Nov 07, 2023 8:32 am
-
-
clutch and throwout bearing wear? Attachment(s)
by pett3227b » Fri Mar 18, 2022 8:08 am » in Farmall Cub - 1
- 333
-
by Glen
Fri Mar 18, 2022 8:45 pm
-
-
- 10
- 562
-
by Clemsonfor
Mon Oct 25, 2021 8:16 pm
-
-
How to install A&I A-PR199 Rings? No instructions available from sellers
by wrascoe » Wed Nov 22, 2023 4:30 pm » in Farmall Cub - 7
- 379
-
by Gary Dotson
Fri Nov 24, 2023 8:38 am
-
Who is online
Users browsing this forum: No registered users and 1 guest