This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link:
Privacy Policy

NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.

Super A help

Farmall Super A, AV, 100, 130, & 140 1939 - 1973
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Jong1821
Posts: 12
Joined: Mon May 20, 2019 6:56 pm
Zip Code: 14006

Super A help

Postby Jong1821 » Mon May 20, 2019 7:12 pm

I picked up a super a from my buddy for 750$. A couple days ago he fired it up and it ran for about 30 seconds then stopped and wouldn't start again. I changed the plugs and cleaned the carb. Still won't fire. I hooked a spark plug to the coil out and put it on bare metal. I got a spark a couple times but not as frequent as I expected. Any tips would be greatly appreciated.

User avatar
Slim140
5+ Years
5+ Years
Posts: 4908
Joined: Wed Nov 22, 2017 6:24 am
Zip Code: 00000
Tractors Owned: .
1970 International 140
1972 International 140
1949 John Deere A
1993 Ford 4630 W/Loader
1965 John Deere 110
1961 Cub Cadet Original
Circle of Safety: Y

Re: Super A help

Postby Slim140 » Mon May 20, 2019 9:31 pm

Probably needs a set of points in it.
Every home is a school, what are you teaching?

Circle of Safety

Jong1821
Posts: 12
Joined: Mon May 20, 2019 6:56 pm
Zip Code: 14006

Re: Super A help

Postby Jong1821 » Tue May 21, 2019 6:15 pm

I got a tune up kit that has the points, condenser, cap and rotor. From what I am reading I need to get the motor to top dead center. In the manual it says when the impulse coupling trips the rotor should be pointing to the #1 post. The post is at about 2 o'clock and after mine trips the rotor is at 3 o'clock. Is this where it should be?

outdoors4evr
10+ Years
10+ Years
Posts: 2791
Joined: Tue Jul 22, 2008 12:44 pm
Zip Code: 48370
Tractors Owned: 184
Location: Oxford, MI

Re: Super A help

Postby outdoors4evr » Wed May 22, 2019 7:52 am

The #1 post should be wherever the rotor is pointing at TDC. (as a starting point). The impulse should snap right at TDC. I think most end up around 1 o'clock.
184 w/ Creeper & 3-Point
IH 3160a Mower
IH Model 15 Tiller
IH-54 Blade

Jong1821
Posts: 12
Joined: Mon May 20, 2019 6:56 pm
Zip Code: 14006

Re: Super A help

Postby Jong1821 » Wed May 22, 2019 10:17 am

So mine might be out of time. The rotor pauses for a second at the post and then moves past it when the impulse coupling trips.

Jong1821
Posts: 12
Joined: Mon May 20, 2019 6:56 pm
Zip Code: 14006

Re: Super A help

Postby Jong1821 » Wed May 22, 2019 10:33 am

I found a video of a magneto rebuild. It looks like she stops after the impulse from the previous cylindar impulse. I think I'm just cranking it past where I should be. I'm going to give it a go after work today. Thanks for the help.

Jong1821
Posts: 12
Joined: Mon May 20, 2019 6:56 pm
Zip Code: 14006

Re: Super A help

Postby Jong1821 » Sun May 26, 2019 3:36 pm

So I changed the points wednesday and still no spark. I left it for a few days and when I came home today I decided to tinker a bit. I had spark from the coil then tested each cylindar and had spark on all 4. It fired up for about 2 minutes and then died again. There was some white crusty stuff near the condenser so I cleaned the area and replaced it. The one that came with my tune up kit is a bit shorter than the one that was in it. Any ideas or input would be appreciated. Thanks.

Jong1821
Posts: 12
Joined: Mon May 20, 2019 6:56 pm
Zip Code: 14006

Re: Super A help

Postby Jong1821 » Tue May 28, 2019 5:08 pm

Any ideas? I'm at a loss here.

Jong1821
Posts: 12
Joined: Mon May 20, 2019 6:56 pm
Zip Code: 14006

Re: Super A help

Postby Jong1821 » Wed May 29, 2019 8:05 pm

I figured it out. I didn't tighten the lower contact for the points enough and it rattled loose. Got everything right and right. She fired on the second crank.


  • Similar Topics
    Replies
    Views
    Last post

Return to “Farmall A, Super A, AV, 100, 130 & 140”

Who is online

Users browsing this forum: No registered users and 1 guest