This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Super A Snowplow mount
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- Cub Star
- Posts: 70
- Joined: Sun Oct 13, 2019 12:19 pm
- Zip Code: 04079
Super A Snowplow mount
I have a why question.
Looking at the large U shaped mount of the snowplow mount hanging vertically there is a short piece on the left side of the tractor when mounted with 2 bolts thru it to make a full U. On the parts diagram/listing for the A60 snowplow it is #11, 650 348 R1. In my case a PO welded it to part #6, 650 347 R91 rather than bolting it. Any idea why \Farmall made the U in 2 pieces and had holes for adjustability?
After snowplow season I will grind out the welds and return it to how Farmall built it.
As an aside, I found this picture of an old, 2017, for sale posting at a price of $300. That was a good price I think both then and now. I paid a bit more for my tractor because it had the snowplow. In fact I would not have bought it without the snowplow. As I understand it the A60 is quite a bit harder to find than an A54.
Note: Not my plow
-
- Team Cub
- Posts: 17279
- Joined: Sun Feb 02, 2003 2:59 pm
- Zip Code: 55319
- Circle of Safety: Y
- Location: MN
Re: Super A Snowplow mount
I've had the same question since I was about 12 years old. Still haven't seen an answer.
-
- Cub Star
- Posts: 70
- Joined: Sun Oct 13, 2019 12:19 pm
- Zip Code: 04079
Re: Super A Snowplow mount
Jim,
Was the A60 designed to be used with other Farmall tractors of the era?
Was the A60 designed to be used with other Farmall tractors of the era?
-
- Team Cub
- Posts: 17279
- Joined: Sun Feb 02, 2003 2:59 pm
- Zip Code: 55319
- Circle of Safety: Y
- Location: MN
Re: Super A Snowplow mount
Not that I am aware of, just the A and Super A.
-
- 10+ Years
- Posts: 2499
- Joined: Sun Feb 17, 2008 2:38 am
- Zip Code: 07727
- Tractors Owned: 1 -'58 International Cub Lo-Boy
2 - '46 International A's
2 - '52 Farmall Cubs
1 - '53 Farmall Super A
1 - ‘41 Ford 9N with a ‘49 8N Engine
1 - ‘48 (5641) Allis Chalmers G - Location: Farmingdale NJ
Re: Super A Snowplow mount
49willard wrote:super a snowplow picture.jpg
I have a why question.
Looking at the large U shaped mount of the snowplow mount hanging vertically there is a short piece on the left side of the tractor when mounted with 2 bolts thru it to make a full U. On the parts diagram/listing for the A60 snowplow it is #11, 650 348 R1. In my case a PO welded it to part #6, 650 347 R91 rather than bolting it. Any idea why \Farmall made the U in 2 pieces and had holes for adjustability?
After snowplow season I will grind out the welds and return it to how Farmall built it.
As an aside, I found this picture of an old, 2017, for sale posting at a price of $300. That was a good price I think both then and now. I paid a bit more for my tractor because it had the snowplow. In fact I would not have bought it without the snowplow. As I understand it the A60 is quite a bit harder to find than an A54.
Note: Not my plow
Not sure if I follow you but I have 3 of these setups and I don’t see anything out of the ordinary in you pic aside from the additional bracing to the frame. That was commonplace because if you use the plow as intended the frame will bend.
Quote by Gary Pickeral I like
"If it can cast a shadow, it can be restored"
"If it can cast a shadow, it can be restored"
-
- 10+ Years
- Posts: 2499
- Joined: Sun Feb 17, 2008 2:38 am
- Zip Code: 07727
- Tractors Owned: 1 -'58 International Cub Lo-Boy
2 - '46 International A's
2 - '52 Farmall Cubs
1 - '53 Farmall Super A
1 - ‘41 Ford 9N with a ‘49 8N Engine
1 - ‘48 (5641) Allis Chalmers G - Location: Farmingdale NJ
Re: Super A Snowplow mount
49willard wrote:Jim,
Was the A60 designed to be used with other Farmall tractors of the era?
The A60 was followed with a version that had a pressure spring rod assembly that replaced the two bars that connect the lift arm to the blade frame. It’s the same style used on the later Cub assemblies only bigger. This plow can be used on the “A” with a hand lift and is used on the 100, 130, and 140 tractors with the same hardware that the Super A uses.
Quote by Gary Pickeral I like
"If it can cast a shadow, it can be restored"
"If it can cast a shadow, it can be restored"
-
- Similar Topics
- Replies
- Views
- Last post
-
-
Shop Made DIY Disc Hiller Mid Mount Tool Bar
by southern-jim » Thu Mar 30, 2023 12:43 pm » in Farmall A, Super A, AV, 100, 130 & 140 - 5
- 503
-
by workinonit
Wed May 17, 2023 9:57 am
-
-
-
Need to I.D Super A
by browning1 » Sun Nov 05, 2023 8:19 pm » in Farmall A, Super A, AV, 100, 130 & 140 - 5
- 926
-
by browning1
Fri Jan 26, 2024 3:36 pm
-
-
-
First Super A Attachment(s)
by CDKL » Tue May 31, 2022 10:38 am » in Farmall A, Super A, AV, 100, 130 & 140 - 24
- 815
-
by Ole Timey Farmin
Sat Jun 18, 2022 3:53 pm
-
-
- 5
- 201
-
by Ang
Thu Jan 19, 2023 3:19 pm
-
- 1
- 165
-
by ShawnAgne
Tue Jan 24, 2023 9:40 pm
Return to “Farmall A, Super A, AV, 100, 130 & 140”
Who is online
Users browsing this forum: No registered users and 0 guests