Just wanted to say hello.
I'm in southern Ohio area.
Bought me a beat up 185 last spring (2011) and bush hogged 4 acres of grass that had not been cut for 3 years immediately with the old girl. She bogged a few times but got the job done.
Then I maintained my 5 acres with her for the rest of the summer. She never missed a lick.
This spring I had to file my points and clean my cap & rotor because she woke up missing badly after sitting in the garage all winter ( had her full of sea-foamed gas for storage). Threw in a set of new plugs too and mowed the place with zero issues.
Well I decided to tighten the left side belt on my belly mower as she was kinda sloppy all last summer compared to the right side.
Of course after I did this, the old girl mowed about 15 minutes with no problem & then threw the darn belt I had just adjusted. The belt was pretty ragged anyway & I was surprised it lasted all last summer from the heavy mowing.
Belt is not broke, just has the cable coming out of the inside and now won't stay on no matter the adjustment.
I'm not sure what kind of mower this has. Doesn't look to be a Woods to me.Says IH in a square sticker on it on both sides with a thin white stripe under it. Uses 3 belts instead of one big one. I'm wondering what the procedure is for changing out the bad belt and adjusting it. Looks like the 3 blade pulley's on the deck are held in place with 4 bolts each in slots. Of course I need to remove the drive pulley coming off the PTO to swap out the left pulley. PTO pulley is on top of the middle blade 3 pulley setup - then left side in middle slot, then right side in bottom slot.
Do I loosen the middle pulley to remove the PTO belt so I can get to the side blade pulley belt?
Any certain order to follow to remove and then re-adjust?
Any advice on where to buy the replacement belt or what brand?
Thanks in advance for all input.
I'll take a few pics in the morning and post them. Don't laugh.......she's not a beauty queen but she does the job. Planning on dolling her up when I get time.
Again HELLO & THANKS!
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
HI YA! new member with 185 Lo-boy mower question
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 8
- Joined: Sun Mar 25, 2012 5:33 pm
- Zip Code: 45616
- Tractors Owned: 185 Cub Lowboy
- Location: southern Ohio
HI YA! new member with 185 Lo-boy mower question
Last edited by crazee on Tue Mar 27, 2012 5:54 am, edited 2 times in total.
-
- 10+ Years
- Posts: 1189
- Joined: Sat May 14, 2011 6:09 pm
- Zip Code: 15132
- Tractors Owned: 53 F Cub
73 F Cub
53 Super A With Snow/Grader Blade
193 Plow With Colter And Jointer
144 Cultivators
22 Mower - Circle of Safety: Y
- Location: Versailles,Pa.
Re: HI YA! new member with 185 Lowboy mower question
welcome Crazee. I can't answer your questions, but someone will be along shortly that can.
Tom
Tom
Know Your Cub, And Your Cub Will Know You.
Tom
Tom
-
- 10+ Years
- Posts: 8
- Joined: Sun Mar 25, 2012 5:33 pm
- Zip Code: 45616
- Tractors Owned: 185 Cub Lowboy
- Location: southern Ohio
Re: HI YA! new member with 185 Lowboy mower question
Thanks
I'm attempting to figure out which deck I have. Maybe the 3160? Like I said, I'll post pics in the morning when it's light out. ( tractor sitting out back tonight).
5Ft deck I think.
I'm attempting to figure out which deck I have. Maybe the 3160? Like I said, I'll post pics in the morning when it's light out. ( tractor sitting out back tonight).
5Ft deck I think.
-
- Cub Pro
- Posts: 1906
- Joined: Tue Jan 18, 2011 9:16 am
- Zip Code: 72940
- Tractors Owned: 1951 Farmall Cub, 152 disk plow, 2 gang disk, belly mower, sickle mower
1949 Farmall Cub, cultivator, moldboard plow, disk,front blade. Cub Cadet, LTX1045 Mower. Cub Cadet's 109, 125, 1000, and 1250
1961 cub c2 belly mower and full blade. 48 cub manual lift with cultivators.
1947 Cub - Circle of Safety: Y
- Location: Huntington, AR
Re: HI YA! new member with 185 Lowboy mower question
Welcome from Arkansas. I bet someone will recognize it once you post the pictures, maybe a C-3, just a guess. Be careful working with these little ole cubs -- they will get you hooked and you will have to get another one with a mower to use while one is down. Never changed a belt on one like you describe.
-
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger - Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
Re: HI YA! new member with 185 Lowboy mower question
G'day to ya Click the following links
IH 3160 Rotary Cutter
IH 3260 Rotary Cutter
IH 60 Inch Rotary Mower
I do not have a lot of information for the Numbered Cubs but what I do have can be found here: Numbered Series Cubs, look under Cub-185 Lo-Boy for the Owner's Manual and under Cub-154 Lo-Boy for the Parts Catalog that shows the different mowers.
Also, there is a lot of other information/resources for our members, just follow the links below:
IH 3160 Rotary Cutter
IH 3260 Rotary Cutter
IH 60 Inch Rotary Mower
I do not have a lot of information for the Numbered Cubs but what I do have can be found here: Numbered Series Cubs, look under Cub-185 Lo-Boy for the Owner's Manual and under Cub-154 Lo-Boy for the Parts Catalog that shows the different mowers.
Also, there is a lot of other information/resources for our members, just follow the links below:
to Farmallcub.com Forum Family. And you have come to the right place for all things Cub related. If you click on the Site Rules, Regulations, & Important Information, it will point you to the Welcome Wagon wherein you will find links to many useful sites and topics. One of which is the Cub Manual Server. Enjoy!.
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship
-
- Cub Pro
- Posts: 4436
- Joined: Wed Dec 26, 2007 7:45 pm
- Zip Code: 32536
- Circle of Safety: Y
- Location: FL, Crestview
Re: HI YA! new member with 185 Lowboy mower question
Welcome to the Forum!,
After you figure out the exact model of the deck you have, then we can get you pointed in the right direction with belt numbers, placement and how to tighten them.
After you figure out the exact model of the deck you have, then we can get you pointed in the right direction with belt numbers, placement and how to tighten them.
Screwstick #3934
FCub - LoBoy - Numbered Series - Power Unit Databases
FCub - LoBoy - Numbered Series - Power Unit Databases
-
- 10+ Years
- Posts: 8
- Joined: Sun Mar 25, 2012 5:33 pm
- Zip Code: 45616
- Tractors Owned: 185 Cub Lowboy
- Location: southern Ohio
Re: HI YA! new member with 185 Loboy mower question
Here are pics of deck and my homely yet lovely Cub 185. Been so busy using the old girl I haven't had time to properly clean her up.
I have done the important stuff like lube and change oil and such of course. I am a gear-head after-all, lol.
And of course I'm missing the expensive to replace front grill. Figure I'll make a custom one and add bolt on bug-eye headlights until I run on to a decent front surround for a good price.
So ........ is this a 3160 deck as I thought? And what are the best way to change belts and adjust (certain order? etc.) What belts are best to get & where? All that good info & advice I need to know.
Thanks again
PS---- I LOVE how nice this machine cuts grass. Makes it look like a golf course and FAST! and sips gasoline too!
I have done the important stuff like lube and change oil and such of course. I am a gear-head after-all, lol.
And of course I'm missing the expensive to replace front grill. Figure I'll make a custom one and add bolt on bug-eye headlights until I run on to a decent front surround for a good price.
So ........ is this a 3160 deck as I thought? And what are the best way to change belts and adjust (certain order? etc.) What belts are best to get & where? All that good info & advice I need to know.
Thanks again
PS---- I LOVE how nice this machine cuts grass. Makes it look like a golf course and FAST! and sips gasoline too!
Last edited by crazee on Tue Mar 27, 2012 5:52 am, edited 1 time in total.
-
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger - Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
Re: HI YA! new member with 185 Lowboy mower question
Looks like an IH 3160 to me... compare the Manual with your pics and it is pretty clear right from the first pic. Nice looking mower
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship
-
- 10+ Years
- Posts: 8
- Joined: Sun Mar 25, 2012 5:33 pm
- Zip Code: 45616
- Tractors Owned: 185 Cub Lowboy
- Location: southern Ohio
Re: HI YA! new member with 185 Loboy mower question
Rudi wrote:Looks like an IH 3160 to me... compare the Manual with your pics and it is pretty clear right from the first pic. Nice looking mower
Yeah, I though so too. Just wasn't 100% sure since the pulley covers are missing.
Now I just need to figure out proper belt change method -proper adjustment - belt type - where to buy info. Wonder if tractor supply has the belts??? Nearest Case dealer is Circleville which is 50 miles north.
BTW- I gave $900 for this tractor. So, it's definitely worth fixing up and keeping IMHO.
It has no blow-by except a tiny bit when under extreme load coming out of the oil spout.
Not charging so I have to charge battery after every several hours of use.Not a huge deal so I have not looked into why and fixed it yet. Maybe the old points regulator?
Clutch & hydraulics seems fine. Brakes are good enough. It started dripping a tiny bit of oil or hydraulic fluid from somewhere under the trans area on to the top back of mower deck this spring. Not enough to get alarmed about, just a few drips. Tires are kinda cracked but seem solid and hold air just fine. Not sure what the air pressure should be.
Just a bunch of details to work out.
Last edited by crazee on Tue Mar 27, 2012 5:52 am, edited 1 time in total.
-
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger - Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
Re: HI YA! new member with 185 Lowboy mower question
I can't help with tensioning/belt size etc., as I am not really familiar with the Numbered Series. However, if you click on the link below for Carter & Grunewald and talk to Ken Updike, I know Ken will be able to get you what you need. No sense driving that far ifn you can get it in the mail.
You got a good deal at $900.00 Definitely worth playing with
You got a good deal at $900.00 Definitely worth playing with
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship
-
- 10+ Years
- Posts: 4123
- Joined: Thu Nov 09, 2006 11:26 pm
- Zip Code: 61722
Re: HI YA! new member with 185 Lo-boy mower question
Looks like the 3160 that is on my first 185----they are a bear to work on!---First thing is to take the deck off and back the tractor off over the deck on blocks, (some guys frown at me when I say to do this,--but I do it all the time)---Then you will need to get ALL the spindle bolts loose WITHOUT breaking them off ( I think a 3/4" socket fits them,---thats what mine are). Turn each one very carefully in both directions and get oil started around the threads and take them completely out and clean the threads so as to remove the rust!---these castings have to slide easy to get belts tight.
After putting on the new belts I start with the short ones first then drag the center one back last. you will at some point have to loosen the pulleys back at the angle changer and re-adjust the whole thing when you put the deck back under the mower.---Flip the deck over and remove the blades and sharpen them while the deck is out.---make sure these bolts work freely too!
Welcome to a great forum! thanks; sonny
After putting on the new belts I start with the short ones first then drag the center one back last. you will at some point have to loosen the pulleys back at the angle changer and re-adjust the whole thing when you put the deck back under the mower.---Flip the deck over and remove the blades and sharpen them while the deck is out.---make sure these bolts work freely too!
Welcome to a great forum! thanks; sonny
-
- 10+ Years
- Posts: 8
- Joined: Sun Mar 25, 2012 5:33 pm
- Zip Code: 45616
- Tractors Owned: 185 Cub Lowboy
- Location: southern Ohio
Re: HI YA! new member with 185 Lo-boy mower question
SONNY wrote:Looks like the 3160 that is on my first 185----they are a bear to work on!---First thing is to take the deck off and back the tractor off over the deck on blocks, (some guys frown at me when I say to do this,--but I do it all the time)---Then you will need to get ALL the spindle bolts loose WITHOUT breaking them off ( I think a 3/4" socket fits them,---thats what mine are). Turn each one very carefully in both directions and get oil started around the threads and take them completely out and clean the threads so as to remove the rust!---these castings have to slide easy to get belts tight.
After putting on the new belts I start with the short ones first then drag the center one back last. you will at some point have to loosen the pulleys back at the angle changer and re-adjust the whole thing when you put the deck back under the mower.---Flip the deck over and remove the blades and sharpen them while the deck is out.---make sure these bolts work freely too!
Welcome to a great forum! thanks; sonny
Thanks, But I think I'll just change the one belt that needs it ( right side). Already had that spindle loose ( thank you PB blaster ). I'm just wanting to cut more grass, not over haul the deck. She is cutting just fine.....just needs a belt. The old girl is a work horse rather than my hobby.
My plan is ( using common sense) to loosen center spindle... loosen right spindle.... lift off center belt to get to right belt. replace right belt... tighten center spindle back to previous position. Tighten right belt. GO CUT GRASS.
Looks like tractor supply sells the belt. 5/8 x 56 ( Case calls it 0.71 x 56.85).
Thanks for the advice. It all sounds very sound.
Maybe come fall I'll actually remove the deck and give her a good going over, paint her up and such.... but for now I'm just going to use her without doing anything not really needed.
-
- 10+ Years
- Posts: 8
- Joined: Sun Mar 25, 2012 5:33 pm
- Zip Code: 45616
- Tractors Owned: 185 Cub Lowboy
- Location: southern Ohio
Re: HI YA! new member with 185 Lo-boy mower question
BTW--->
Procedure is as follows -
1- Drop deck all the way down
2- loosen all 3 pulleys ( the 4 - 3/4" bolts around each pulley)
3- slip off top drive pulley belt from middle pulley(mule drive)
4- Then the middle belt ( right side)
5- then the bottom belt ( left side)
6- re-install in reverse order
7- tighten middle blade pulley first ( which tightens the drive ( mule) belt. ( only tighten this with deck fully down)
8- then tighten left side - then right side
9- tighten about same as you would an alternator belt on your car.
10- go cut grass!
PS--> Hamilton Bob's Cub supply outside Cincinnati, Ohio sells an after market set of belts for the 3160 that are a great price and seem to be very good quality from what I'm seeing so far. They told me 100% guaranteed including return shipping if there is a problem!!!! SUPER nice guys to deal with and they ship out fast! Easy to get on the phone and very helpful. Need I say more.
Procedure is as follows -
1- Drop deck all the way down
2- loosen all 3 pulleys ( the 4 - 3/4" bolts around each pulley)
3- slip off top drive pulley belt from middle pulley(mule drive)
4- Then the middle belt ( right side)
5- then the bottom belt ( left side)
6- re-install in reverse order
7- tighten middle blade pulley first ( which tightens the drive ( mule) belt. ( only tighten this with deck fully down)
8- then tighten left side - then right side
9- tighten about same as you would an alternator belt on your car.
10- go cut grass!
PS--> Hamilton Bob's Cub supply outside Cincinnati, Ohio sells an after market set of belts for the 3160 that are a great price and seem to be very good quality from what I'm seeing so far. They told me 100% guaranteed including return shipping if there is a problem!!!! SUPER nice guys to deal with and they ship out fast! Easy to get on the phone and very helpful. Need I say more.
-
- Similar Topics
- Replies
- Views
- Last post
-
- 6
- 444
-
by outdoors4evr
Fri Aug 12, 2022 5:22 am
-
-
Cub Low Boy 154 Mower question?
by Hausfire28 » Sun Mar 31, 2024 8:07 pm » in Lo-Boy Series - 154, 184, 185 - 2
- 138
-
by outdoors4evr
Wed Apr 17, 2024 7:34 am
-
-
- 7
- 374
-
by Eugene
Mon Feb 13, 2023 10:28 am
-
-
184 + junk mower Attachment(s)
by SONNY » Sat Dec 10, 2022 8:22 pm » in Lo-Boy Series - 154, 184, 185 - 10
- 558
-
by SONNY
Thu Jan 26, 2023 3:51 pm
-
-
- 9
- 411
-
by Eugene
Tue Sep 27, 2022 5:53 pm
Return to “Lo-Boy Series - 154, 184, 185”
Who is online
Users browsing this forum: No registered users and 2 guests