This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Farmall B wheel bearings/steering
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 41
- Joined: Tue May 25, 2004 6:35 am
- Location: Iowa
Farmall B wheel bearings/steering
Does anyone have bearing numbers for the front wheels of a '42 B? I also want to replace the (bushing?) that is in the tricycle stem - that whole part is loose on my tractor. Any suggestions on tightening up the play in the steering would be much appreciated.
-
- Team Cub Guide
- Posts: 3544
- Joined: Sun Feb 02, 2003 6:30 pm
- Zip Code: 38658
- eBay ID: Cub-Bud
- Tractors Owned: Four FCUBs, one IH Lo-Boy, one B Farmall, two Cadets, and a John Deere B.
- Circle of Safety: Y
- Location: MS, Pope
I just finished rebuilding the front bolster on my '45 B and replaced a bad wheel bearing. The wheel bearings and seals from Case/IH are very expensive. However, the bearings and seals for the bolster are competitive. I also replaced the bearing on the end of the steering shaft (worm shaft). Replacing the bearings will remove all of the play and tighten everything up. It is the only way to go.
I found this on Ebay the other night. You might find a similar kit from your local farm parts dealers. The seals alone from Case/IH cost as much as this kit.
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&category=56175&item=3855270833&rd=1
I can supply you with some Case/IH part numbers later tonight.
I found this on Ebay the other night. You might find a similar kit from your local farm parts dealers. The seals alone from Case/IH cost as much as this kit.
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&category=56175&item=3855270833&rd=1
I can supply you with some Case/IH part numbers later tonight.
"Never forget where it is you come from, or you may find yourself someplace you don't want to be"
Greg Norman
Greg Norman
-
- Team Cub Guide
- Posts: 3544
- Joined: Sun Feb 02, 2003 6:30 pm
- Zip Code: 38658
- eBay ID: Cub-Bud
- Tractors Owned: Four FCUBs, one IH Lo-Boy, one B Farmall, two Cadets, and a John Deere B.
- Circle of Safety: Y
- Location: MS, Pope
Here are the IH part #s and prices I paid for the bearings, seal, and gaskets in the bolster:
377788R91....seal....$18.00
52951D.....gasket.....$4.55
52952D.....gasket.....$4.55
ST269A.....bearing....$52.73 (this bearing at Napa was $99.00)
ST278.......bearing....$48.09
I purchased the bearing for the steering worm shaft from Napa. I had to remove the sheilds so it would get oil:
P6205-2RSJ..........$7.34
I hope this helps.
377788R91....seal....$18.00
52951D.....gasket.....$4.55
52952D.....gasket.....$4.55
ST269A.....bearing....$52.73 (this bearing at Napa was $99.00)
ST278.......bearing....$48.09
I purchased the bearing for the steering worm shaft from Napa. I had to remove the sheilds so it would get oil:
P6205-2RSJ..........$7.34
I hope this helps.
"Never forget where it is you come from, or you may find yourself someplace you don't want to be"
Greg Norman
Greg Norman
-
- Similar Topics
- Replies
- Views
- Last post
-
-
Wheel Thingy? Attachment(s)
by Old Machinist » Wed Dec 21, 2022 10:30 am » in Other Tractors and Machinery - 1
- 238
-
by Urbish
Wed Dec 21, 2022 10:47 am
-
-
- 2
- 236
-
by tldec50
Mon May 09, 2022 7:43 pm
-
-
grease bolt for hay wagon steering source? Attachment(s)
by inairam » Fri May 07, 2021 5:33 pm » in Other Tractors and Machinery - 8
- 653
-
by SONNY
Mon May 10, 2021 9:55 am
-
Return to “Other Tractors and Machinery”
Who is online
Users browsing this forum: No registered users and 0 guests