This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
building suggestions
-
- Cub Pro
- Posts: 23701
- Joined: Sun Feb 02, 2003 2:09 pm
- Zip Code: 63664
- Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
- Location: Mo, Potosi
building suggestions
We are considiering selling our farm, and if we do, will be putting up a building at my place for the cubs and other machinery. It will be primarily storage, but due to my health, only light maintenace will be done in it. I am presently considering a 24x30 or 24x32 building with 10 foot sidewalls to give me enough height for a lean-to on each side that can be used for trailers, some implements, etc. I plan sliding doors on each end, as well as one walk in door. The building will be metal and insulated, with a concrete floor, whille the lean-tos will have gravel floors. Does anyone have suggestions I should consider, such as things to do in building, or possibly different sizes that would work better. cost is a factor.
If you are not part of the solution,
you are part of the problem!!!
you are part of the problem!!!
-
- Team Cub Mentor
- Posts: 20399
- Joined: Fri Jul 02, 2004 9:52 pm
- Zip Code: 65051
- Circle of Safety: Y
- Location: Mo. Linn
The biggest shop money will allow. No matter the size, it will quickly fill up.
A few year back my dad purchased an all metal building, 24' by 36'. Arched tublar bolt together metal frame. Two people put the building up in just over 8 hours on a level pad.
Plan the electrical installation, welder, provisions for heating, water and sewage before construction. They don't have to be put in during construction. Just in case the house burns down you have some place to live.
The shop building would be a good place to put the standby generator, with larger fuel tank. Might plan this into the electrical system.
One thing my son and I are going to put in a planned shop is floor anchors in the maintenance area - those recessed anchor points in the floor for chaining down machinery - parts.
A frame or suspended rail for splitting tractors.
Another thought. The entire shop floor doesn't have to be cement. Just the center section where you would work on machinery. The area to each side of the two larger doors could be graveled since this is usually used for storage
Eugene
A few year back my dad purchased an all metal building, 24' by 36'. Arched tublar bolt together metal frame. Two people put the building up in just over 8 hours on a level pad.
Plan the electrical installation, welder, provisions for heating, water and sewage before construction. They don't have to be put in during construction. Just in case the house burns down you have some place to live.
The shop building would be a good place to put the standby generator, with larger fuel tank. Might plan this into the electrical system.
One thing my son and I are going to put in a planned shop is floor anchors in the maintenance area - those recessed anchor points in the floor for chaining down machinery - parts.
A frame or suspended rail for splitting tractors.
Another thought. The entire shop floor doesn't have to be cement. Just the center section where you would work on machinery. The area to each side of the two larger doors could be graveled since this is usually used for storage
Eugene
-
- Cub Pro
- Posts: 3421
- Joined: Fri Sep 24, 2004 9:02 pm
- Zip Code: 30543
- Tractors Owned: 1948 Cub
- Circle of Safety: Y
- Location: Ga. Gillsville
John,
My shop is 28'x55' has a 12' ceiling, two 10' roll up doors and a entry door and is too small. Or should I say full aready!
Be sure to insulate, install electrical and plumbing if wanted while building the shop. Consider how you might want to heat it in the winter too. As Eugene said the biggest the budget will allow.
My shop is 28'x55' has a 12' ceiling, two 10' roll up doors and a entry door and is too small. Or should I say full aready!
Be sure to insulate, install electrical and plumbing if wanted while building the shop. Consider how you might want to heat it in the winter too. As Eugene said the biggest the budget will allow.
I bought an old tractor all dusty and worn,
knew nothing about her just the year she was born
I washed her and greased her and painted her red
Now she lives happily right here in my shed.
HOME of THE STONETHROW CUBFEST
2007 Cub Tug Champion
knew nothing about her just the year she was born
I washed her and greased her and painted her red
Now she lives happily right here in my shed.
HOME of THE STONETHROW CUBFEST
2007 Cub Tug Champion
-
- Cub Pro
- Posts: 2575
- Joined: Mon Feb 03, 2003 5:25 am
- Zip Code: 37774
- Tractors Owned: 1948 McCormick-Deering Farmall Cub
152 Disc Plow & Flat Belt Pulley
Brinly #8 Moldboard Plow
1971 JD 112 Garden Tractor
1928 Economy Hit & Miss Engine
1927 David Bradley "Little Wonder" Feed Grinder
1 A.H. Patch Corn Shellers
1 A.H. Patch #1 Grist Mill - Circle of Safety: Y
- Location: TN, Loudon (near Knoxville)
Hey John...Regardless of what SIZE you build your barn/shop...you'll find out in a hurry that it will NEVER be BIG ENOUGH The hardest delema for "geezers" or soon-to-be geezers like us is this: The issue of DOWNSIZING vs RETIREMENT TIME FOR HOBBIES
As you git OLDER...you WANT to DOWNSIZE, but the MORE time you have...the MORE THINGS you aquire to PLAY WITH! This ALWAYS results in most of us building any garage or barn/shop TOO SMALL SOOoooo...Use Country's Rule on shop size...Figure out how much room & stuff ya have NOW...THEN DOUBLE IT! When I designed my 28'W X 43'L X 14'H EXTRA garage for my "junk" I figured it would be HUGE! Well, I FILLED IT UP in less than 3 years of retirement...and NOW, if I want to BUY something...I have to SELL something else (i.e. 1930 Ford Streetrod meant sellin' 1946 Farmall M). Those kind of heart-wrenching decisions are just too tough on a geezer AND...SIZE MATTERS, so DON'T EVER LISTEN TO YOUR WIFE cause they'll ALWAYS tell ya..."You Don't Need Something That BIG"
As you git OLDER...you WANT to DOWNSIZE, but the MORE time you have...the MORE THINGS you aquire to PLAY WITH! This ALWAYS results in most of us building any garage or barn/shop TOO SMALL SOOoooo...Use Country's Rule on shop size...Figure out how much room & stuff ya have NOW...THEN DOUBLE IT! When I designed my 28'W X 43'L X 14'H EXTRA garage for my "junk" I figured it would be HUGE! Well, I FILLED IT UP in less than 3 years of retirement...and NOW, if I want to BUY something...I have to SELL something else (i.e. 1930 Ford Streetrod meant sellin' 1946 Farmall M). Those kind of heart-wrenching decisions are just too tough on a geezer AND...SIZE MATTERS, so DON'T EVER LISTEN TO YOUR WIFE cause they'll ALWAYS tell ya..."You Don't Need Something That BIG"
"Save The Possums...Collect The Whole Set"
"Tennessee Sun-Dried Possum...Heaven In A Can"
"Tennessee Sun-Dried Possum...Heaven In A Can"
-
- 10+ Years
- Posts: 72
- Joined: Wed Apr 26, 2006 4:03 pm
- Location: Zion Hill, Pa
I've owned 3 different buildings so far. 2 where on the property when I bought it and 1 that I built myself. If I had it to do all over I would make sure I put radiant heat tube in the concrete floor whether you plan on heating now or in the future. It can't be retro-fitted later, and it sure make it easy on my old-guy feet in the cold weather. Also, I knew a fellow who had a huge building with a car lift. He had his radiant heat set up in zones, one just around the lift so he wouldn't have to heat the whole shop just to work on the car. Pretty good thinking I thought.
"Outside of a dog, a book is a man's best friend; inside of a dog, it's to dark to read." -- Marx
-
- 10+ Years
- Posts: 3414
- Joined: Sat May 15, 2004 11:10 am
- Zip Code: 49229
- Location: MI, Britton
Hi John
We are looking at puting up a 24x40 at the farm. My uncle has one with 10' sidewalls when he put a lean to on it he ran out of head room fast. So we are going to go with a 12' or 14' side wall. I would also sugest that you build it up so floor is at least a foot above the surrounding ground. You know you drainage best. But it seems you build the floor a few inches higher and in a few years all the water wants to come inside.
Billy
We are looking at puting up a 24x40 at the farm. My uncle has one with 10' sidewalls when he put a lean to on it he ran out of head room fast. So we are going to go with a 12' or 14' side wall. I would also sugest that you build it up so floor is at least a foot above the surrounding ground. You know you drainage best. But it seems you build the floor a few inches higher and in a few years all the water wants to come inside.
Billy
Take care of your equipment and it will take care of you. 1964 cub. Farmall 100 and 130.
"Those that say it can’t be done should not interrupt the ones who are doing it.”
"Those that say it can’t be done should not interrupt the ones who are doing it.”
-
- 10+ Years
- Posts: 1132
- Joined: Sun May 29, 2005 1:21 pm
- Zip Code: 04762
- Location: ME, New Sweden
How about those prefab metal storage building kits? They might not be practical anymore since steel has gone up so much recently. Also, if you can have an upstairs attic, for storing all that stuff you will never use again but dont want to throw away becuase you never know when you will need it
Nik - 1948 Farmall Cub
-
- 10+ Years
- Posts: 2680
- Joined: Mon Oct 24, 2005 11:35 am
- Zip Code: 14072
- eBay ID: toysforjake
- Tractors Owned: Lots of Cub Cadets!
1951 Farmall Cub
1977 IH Cub
1966 IH Cub
1965 IH Lo Boy
1964 IH Lo Boy
1949 Farmall Cub
Several IH 154 Lo Boys
1979 IH 184 Lo Boy
Simplicity 4416 Sovereign
Simplicity Conquest
Simplicity Legacy 4x4 Diesel
Mitsubishi MT180D 4x4 Diesel - Circle of Safety: Y
- Location: Grand Island, NY
John,
I helped a friend finish a 24x32 pole barn, and it did fill up fast, but he has a 21' boat that takes up way too much space. One thing I tried to talk him into, at the time he did not think it was worth investigating, was installing a single piece of I-beam across one section of the shop at the ceiling level. He now regrets not listening to me, as it is near impossible to add once the building is finished.
The single piece of I-beam can later have a trolly and simple chain fall added and can be used for many things like an engine hoist, wheel weight lift, lift for getting heavy objects in/out of a truck or car, etc. You can also, if you plan according, install a heavy set of shelving, similar to what you see in Home Depot, at one end of the beam. There you can store extremely heavy things, up off of the floor, on shelves, where they take up much less space. One friend has 3-snow mobiles that he stores on shelving like this, and uses a chain fall to lift them in place. Works great and he now has 3 sleds sitting in one 4' x 8' floor area. This would be a great idea for storage of implements, wheel weights, extra tires, parts, etc. All could be lifted easily and placed up on shelves out of the way.
Best of luck,
Bill
I helped a friend finish a 24x32 pole barn, and it did fill up fast, but he has a 21' boat that takes up way too much space. One thing I tried to talk him into, at the time he did not think it was worth investigating, was installing a single piece of I-beam across one section of the shop at the ceiling level. He now regrets not listening to me, as it is near impossible to add once the building is finished.
The single piece of I-beam can later have a trolly and simple chain fall added and can be used for many things like an engine hoist, wheel weight lift, lift for getting heavy objects in/out of a truck or car, etc. You can also, if you plan according, install a heavy set of shelving, similar to what you see in Home Depot, at one end of the beam. There you can store extremely heavy things, up off of the floor, on shelves, where they take up much less space. One friend has 3-snow mobiles that he stores on shelving like this, and uses a chain fall to lift them in place. Works great and he now has 3 sleds sitting in one 4' x 8' floor area. This would be a great idea for storage of implements, wheel weights, extra tires, parts, etc. All could be lifted easily and placed up on shelves out of the way.
Best of luck,
Bill
Cub Cadets 682, 1811, 1864, Simplicity Legacy XL 4x4 Diesel with FEL, 60" mower, 50" Tiller
-
- Team Cub Mentor
- Posts: 17524
- Joined: Mon Feb 03, 2003 6:45 am
- Zip Code: 21550
- Tractors Owned: "1950 Something" Farmall Cub
1957 Farmall Cub w/FH
1977 International Cub w/FH
1978 International Cub
1948 Farmall Super A - Circle of Safety: Y
- Location: MD, Deep Creek Lake
John,
The things I regret not doing when I built my three bay garage:
1. Not installing a beam as Bill suggested for an overhead trolley.
2. Not putting some sort of vapor barrier under the concrete floor. I specified this, but the contractor didn't do it. I wasn't there when the floor was poured.
3. Not installing a floor drain for each bay. I have one in the center of the garage.
4. Not raising the garage a little higher as Cowboy suggests. I don't have water come in, but it doesn't drain away quickly enough from in front of the doors.
Things I'm glad I did:
1. Installed 9 foot wide garage doors, one of which is 8 feet high. I'd go with 9 or 10 feet high if you have larger tractors.
2. Installed plenty of electrical outlets, two of which are 220V for the welder and compressor.
3. Installed a hose bib inside the garage.
4. Built it with a 10 foot ceiling height.
Suggestions for you:
1. Insulate the space and make provisions for heat, even though you may not install it right away. Mine is insulated to R-13. Even with no heat currently in the garage, water doesn't freeze inside on the coldest nights.
2. Build as much space as you can afford. You can never have too much.
3. Leave plenty of wall space for shelves and work bench areas.
Hope this helps some.
The things I regret not doing when I built my three bay garage:
1. Not installing a beam as Bill suggested for an overhead trolley.
2. Not putting some sort of vapor barrier under the concrete floor. I specified this, but the contractor didn't do it. I wasn't there when the floor was poured.
3. Not installing a floor drain for each bay. I have one in the center of the garage.
4. Not raising the garage a little higher as Cowboy suggests. I don't have water come in, but it doesn't drain away quickly enough from in front of the doors.
Things I'm glad I did:
1. Installed 9 foot wide garage doors, one of which is 8 feet high. I'd go with 9 or 10 feet high if you have larger tractors.
2. Installed plenty of electrical outlets, two of which are 220V for the welder and compressor.
3. Installed a hose bib inside the garage.
4. Built it with a 10 foot ceiling height.
Suggestions for you:
1. Insulate the space and make provisions for heat, even though you may not install it right away. Mine is insulated to R-13. Even with no heat currently in the garage, water doesn't freeze inside on the coldest nights.
2. Build as much space as you can afford. You can never have too much.
3. Leave plenty of wall space for shelves and work bench areas.
Hope this helps some.
-
- 10+ Years
- Posts: 4565
- Joined: Wed Feb 05, 2003 1:18 pm
- Zip Code: 45365
- Tractors Owned: Home to "Rusty", the 2007 and 2009 Cub Tug Champion.
- Circle of Safety: Y
- Location: OH, Sidney
-
- Team Cub Mentor
- Posts: 20399
- Joined: Fri Jul 02, 2004 9:52 pm
- Zip Code: 65051
- Circle of Safety: Y
- Location: Mo. Linn
-
- 10+ Years
- Posts: 418
- Joined: Sat Jan 17, 2004 6:40 pm
- Location: Lordstown, Ohio
i just put a fridge in my barn. having cold water or beer close by has been a treat! seriously though, will you be moving to a warmer climate and what kind of barn construction do you have in mind? some of the suggestions posted so far do hinge on what kind of barn you build. the next barn i get will be easy to maintain.
John
John
-
- 10+ Years
- Posts: 51
- Joined: Sun May 01, 2005 6:36 pm
- Location: Warrenton Mo.
building suggestions
John I know everyone is going to metal buildings and they sure have some great advantages. However I just had a Tuff-Shed put up at my place and am very pleased. The cost was very much in line and the have anything you want. Stock units or they will custon anything you want. I would take the time to check them before you settle on anything.The warranty was every bit as good as metal and they did everything they promissed. Don't purchase through Home Depot go right to Tuff-Shed.
-
- 10+ Years
- Posts: 6547
- Joined: Mon Jul 25, 2005 10:16 pm
- Zip Code: 61944
- Tractors Owned: -
55 F-Cub - snow plow and chains
3 Demonstrators Restored.
"Bette" - 22 mower
"Roxie" - 144 Complete Cults'
"Sandy"(Done) 193 Plow
1950 Demo, "Billie"
-(Woods 59")
Corn Stalk Cutter
23a Disc
&
2005 Mahindra w/FEL - Circle of Safety: Y
- Location: IL, Paris just off of Interstate 70
1. I'd stay away from the skylights. They leak and tend to break, and will not last as long as the time. That was told to me by FIL when i was building my shed. So i have no sky lights, and no leaks.
2. THe building code (snow weight) here (it has to be less there), allows for 9 foot spans on poles. So your dimensions should be divisable by 9. You will get an extra couple of feet for very little cost. I wish i would have followed this when building my 20 x 24 shed with 9 ft over hangs on each side. I later moved one wall out, and made it 29 x24 inside with one overhang. I can get my 5 cubs and the zero turn mower in all at once. I even have the "martha Stewart room" the attic.
3. Goes as big as you can afford. You wont regret it. I would of preferred to have big rollup doors at both ends as well. Sliders there is no way to keep heat in. If you can do the thing in the concrete with heat pump, do it. Plenty of plugs, set up 220. Let me know when you need some wiring done, i can help ya do that.
john
2. THe building code (snow weight) here (it has to be less there), allows for 9 foot spans on poles. So your dimensions should be divisable by 9. You will get an extra couple of feet for very little cost. I wish i would have followed this when building my 20 x 24 shed with 9 ft over hangs on each side. I later moved one wall out, and made it 29 x24 inside with one overhang. I can get my 5 cubs and the zero turn mower in all at once. I even have the "martha Stewart room" the attic.
3. Goes as big as you can afford. You wont regret it. I would of preferred to have big rollup doors at both ends as well. Sliders there is no way to keep heat in. If you can do the thing in the concrete with heat pump, do it. Plenty of plugs, set up 220. Let me know when you need some wiring done, i can help ya do that.
john
-
- Team Cub
- Posts: 17309
- Joined: Sun Feb 02, 2003 2:59 pm
- Zip Code: 55319
- Circle of Safety: Y
- Location: MN
videodoc wrote:1. I'd stay away from the skylights. They leak and tend to break, and will not last as long as the time. That was told to me by FIL when i was building my shed. So i have no sky lights, and no leaks.
My experiencve with windows and skylights suggests the opposite. Leaks around my window have been a long term problem. Sky lights have been no more problem than any other part of the metal roof. So when I added on, I put in 2 sky lights and no windows. If I want to look outside, I can open a door.
-
- Similar Topics
- Replies
- Views
- Last post
-
- 3
- 4520
-
by SamsFarm
Thu Mar 23, 2023 4:20 pm
-
- 10
- 288
-
by Barnyard
Sat May 11, 2024 2:59 pm
-
- 9
- 2643
-
by Bob McCarty
Mon Apr 04, 2022 9:56 am
-
- 5
- 208
-
by inairam
Sun May 28, 2023 6:12 pm
-
-
International Harvester Engineering Building
by ricky racer » Thu Aug 24, 2023 7:17 am » in Off Topic - 1
- 3457
-
by dgrapes59
Thu Aug 24, 2023 8:26 am
-
Return to “Farm Life and Better Half Forum”
Who is online
Users browsing this forum: No registered users and 2 guests