This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Need Help identifying my Cub?
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 15
- Joined: Mon Jan 19, 2004 1:02 pm
- Location: New Alexandria, Pa, USA
Need Help identifying my Cub?
I looked through the information up in the first post and found the serial numbers and corresponding years mine 215144 J shows it as being a 1960 cub. On the side of the transmission below the clutch pedal it shows 351688 R3 L3 what does that mean? then directly on the other side of the transmission it shows 360719 R1, any meaning to that? then on the side of the engine block i see 251341R7 L any meaning to that? I am content with it being a 1960 i just was wondering if anything has been changed or anything through its history?
-
- Team Cub Mentor
- Posts: 17489
- Joined: Mon Feb 03, 2003 6:45 am
- Zip Code: 21550
- Tractors Owned: "1950 Something" Farmall Cub
1957 Farmall Cub w/FH
1977 International Cub w/FH
1978 International Cub
1948 Farmall Super A - Circle of Safety: Y
- Location: MD, Deep Creek Lake
Nova,
Those numbers are part numbers for the torque tube, transmission and engine castings, respectively. To verify the date of manufacture of all of the castings on your tractor, go to the following site.
http://www.tmtractor.com/id/id_001.htm
Good luck,
Those numbers are part numbers for the torque tube, transmission and engine castings, respectively. To verify the date of manufacture of all of the castings on your tractor, go to the following site.
http://www.tmtractor.com/id/id_001.htm
Good luck,
-
- 10+ Years
- Posts: 15
- Joined: Mon Jan 19, 2004 1:02 pm
- Location: New Alexandria, Pa, USA
-
- Cub Pro
- Posts: 7013
- Joined: Sun Feb 02, 2003 9:36 pm
- Zip Code: 43420
- Circle of Safety: Y
- Location: OHIO, Fremont
Nova,
That's very common. The most likely cause is a leaking seal on the side of the differential case that causes the lining to become oil soaked. An archive search for axle seal should get many hits... we talk about it a lot.
That's very common. The most likely cause is a leaking seal on the side of the differential case that causes the lining to become oil soaked. An archive search for axle seal should get many hits... we talk about it a lot.
George Willer
http://gwill.net
The most affectionate creature in the world is a wet dog. Ambrose Bierce
http://gwill.net
The most affectionate creature in the world is a wet dog. Ambrose Bierce
-
- Team Cub Mentor
- Posts: 24144
- Joined: Sun Feb 02, 2003 12:50 pm
- Zip Code: 43113
- Circle of Safety: Y
- Location: OH, Circleville
The brake drum and brake band are inside the final drive housings. Check to make sure the rod from the brake pedal is still connected to the band. The brake band may be completely worn out, the set screw may be loose or missing or the rod may not be connected. Not a particularly difficult job if removing the final drives sounds like fun.
Bigdog
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
http://www.cubtug.com
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
http://www.cubtug.com
-
- 10+ Years
- Posts: 15
- Joined: Mon Jan 19, 2004 1:02 pm
- Location: New Alexandria, Pa, USA
-
- 10+ Years
- Posts: 15
- Joined: Mon Jan 19, 2004 1:02 pm
- Location: New Alexandria, Pa, USA
-
- Team Cub Mentor
- Posts: 24144
- Joined: Sun Feb 02, 2003 12:50 pm
- Zip Code: 43113
- Circle of Safety: Y
- Location: OH, Circleville
Check this link to Rudi's site. It is a page out of the parts manual showing the brake components. You may just have a pin that is missing.
http://www.cleancomputes.com/Cub/Cub%20Parts%20Manuals/TC-37F%20Revision%203/Group%2004%20-%20Brakes/Page%2004-02.jpg Also check the cub FAQs on ATIS for information on decals, emblems etc.
http://www.atis.net/CubFAQ/cub_faq.html
http://www.cleancomputes.com/Cub/Cub%20Parts%20Manuals/TC-37F%20Revision%203/Group%2004%20-%20Brakes/Page%2004-02.jpg Also check the cub FAQs on ATIS for information on decals, emblems etc.
http://www.atis.net/CubFAQ/cub_faq.html
Bigdog
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
http://www.cubtug.com
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
http://www.cubtug.com
-
- Cub Pro
- Posts: 7013
- Joined: Sun Feb 02, 2003 9:36 pm
- Zip Code: 43420
- Circle of Safety: Y
- Location: OHIO, Fremont
Nova,
I think your emblems should be the same as on my '63, so they are probably right. AFAIK, the change from the stainless ones was in 1959. When I fix mine up prettier, I plan to buy a set that is most commonly available from many sources, and simply not use the ones for the hood. All the other ones will be close enough.
Currently, there are none on it.
I think your emblems should be the same as on my '63, so they are probably right. AFAIK, the change from the stainless ones was in 1959. When I fix mine up prettier, I plan to buy a set that is most commonly available from many sources, and simply not use the ones for the hood. All the other ones will be close enough.
Currently, there are none on it.
George Willer
http://gwill.net
The most affectionate creature in the world is a wet dog. Ambrose Bierce
http://gwill.net
The most affectionate creature in the world is a wet dog. Ambrose Bierce
-
- Cub Pro
- Posts: 7013
- Joined: Sun Feb 02, 2003 9:36 pm
- Zip Code: 43420
- Circle of Safety: Y
- Location: OHIO, Fremont
Nova,
Oops, I must have been sleeping! If your emblems are correct, your tractor must be a Lo-Boy? They would have had the International emblem. All the smaller decals were probably the same.
Oops, I must have been sleeping! If your emblems are correct, your tractor must be a Lo-Boy? They would have had the International emblem. All the smaller decals were probably the same.
Last edited by George Willer on Mon Jan 26, 2004 12:35 pm, edited 1 time in total.
George Willer
http://gwill.net
The most affectionate creature in the world is a wet dog. Ambrose Bierce
http://gwill.net
The most affectionate creature in the world is a wet dog. Ambrose Bierce
-
- 10+ Years
- Posts: 15
- Joined: Mon Jan 19, 2004 1:02 pm
- Location: New Alexandria, Pa, USA
-
- Cub Pro
- Posts: 7013
- Joined: Sun Feb 02, 2003 9:36 pm
- Zip Code: 43420
- Circle of Safety: Y
- Location: OHIO, Fremont
Nova,
I went back to my post and see that it was still confusing, so I edited it.
The '60 Lo-Boy would have "International" on the hood side and say "Lo-Boy" on a vertical metal emblem on the hood support.
The '60 to '63 F-Cub would say McCormick Farmall on the hood side and say "Cub" on a metal oval on the hood support.
I went back to my post and see that it was still confusing, so I edited it.
The '60 Lo-Boy would have "International" on the hood side and say "Lo-Boy" on a vertical metal emblem on the hood support.
The '60 to '63 F-Cub would say McCormick Farmall on the hood side and say "Cub" on a metal oval on the hood support.
George Willer
http://gwill.net
The most affectionate creature in the world is a wet dog. Ambrose Bierce
http://gwill.net
The most affectionate creature in the world is a wet dog. Ambrose Bierce
-
- 10+ Years
- Posts: 15
- Joined: Mon Jan 19, 2004 1:02 pm
- Location: New Alexandria, Pa, USA
-
- Cub Pro
- Posts: 7013
- Joined: Sun Feb 02, 2003 9:36 pm
- Zip Code: 43420
- Circle of Safety: Y
- Location: OHIO, Fremont
Nova,
If your sheet metal oil pans for the final drives are on the bottom, you have a regular F-Cub with a lo-boy hood.
If they are on the front, you have a lo-boy with F-Cub hood supports.
If your sheet metal oil pans for the final drives are on the bottom, you have a regular F-Cub with a lo-boy hood.
If they are on the front, you have a lo-boy with F-Cub hood supports.
George Willer
http://gwill.net
The most affectionate creature in the world is a wet dog. Ambrose Bierce
http://gwill.net
The most affectionate creature in the world is a wet dog. Ambrose Bierce
-
- Team Cub
- Posts: 17279
- Joined: Sun Feb 02, 2003 2:59 pm
- Zip Code: 55319
- Circle of Safety: Y
- Location: MN
-
- Similar Topics
- Replies
- Views
- Last post
-
- 13
- 379
-
by Gary Dotson
Mon May 03, 2021 7:38 am
-
-
Identifying clutch parts before buying - 1973 Cub Attachment(s)
by JBP1 » Mon Feb 06, 2023 5:40 pm » in Farmall Cub - 5
- 758
-
by Bill Hudson
Mon Feb 06, 2023 9:09 pm
-
Who is online
Users browsing this forum: Majestic-12 [Bot] and 9 guests