Got the A out of the shed to start getting it ready for it's rebirth. It was missing and running badly the last several times I had it out. The block had a small freeze fracture behind the carb and was leaking anti-freeze, so I thought I was dealing a similar fracture on the head deck of the block. Either that or I had valves sticking.
First thing on my agenda was to observe the valves with the valve cover off. Everything was moving smoothly. I know it makes a big difference if it is at operating temp. and this was not.
Second objective was a compression test. I didn't have the proper adapter to screw my compression gauge into the spark plug hole so I just tried wrapping it with electrical tape and shoving it up against the hole as best I could. I know this is not going to be extremely accurate but I really expected to find # 2 and 3 cylinder (freeze cracked) with 0 compression and this set up would be good enough to tell me that.
My results were very pleasing.....I think. All the cylinders came out within about a .5% of one another. That's pretty good cylinder balance in my book. The thing I don't know is how much pressure should each cylinder render? This is a gas tractor from the midwest , so it shouldn't have any whacky compression ratio pistons (high altitude or distilate).
OK you salty dogs, help me out..........please
Thanks,
Steve
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
1941 A-How many lbs. psi on compression test?
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 41
- Joined: Sun Feb 10, 2008 3:32 pm
- Zip Code: 47960
- Tractors Owned: 1948 C
1941 A
1971 JD 110 - Location: IN, Monticello
-
- Team Cub Mentor
- Posts: 20395
- Joined: Fri Jul 02, 2004 9:52 pm
- Zip Code: 65051
- Circle of Safety: Y
- Location: Mo. Linn
Re: 1941 A-How many lbs. psi on compression test?
As long as the compression is even on all 4 cylinders, the tractor runs fine and does what you want - don't worry about it.
Just guessing. 100 psi would be in the ball park, good. 80 marginal but still satisfactory. However, I have a WC Allis and without looking you could find any one of 7 different piston sets (compression rations) for the original engine. Don't know about an IH 41 A. I have a distilate set in the WC and a fresh engine overhaul. Hand cranking, 70 PSI is the best I can get.
Just guessing. 100 psi would be in the ball park, good. 80 marginal but still satisfactory. However, I have a WC Allis and without looking you could find any one of 7 different piston sets (compression rations) for the original engine. Don't know about an IH 41 A. I have a distilate set in the WC and a fresh engine overhaul. Hand cranking, 70 PSI is the best I can get.
I have an excuse. CRS.
-
- 10+ Years
- Posts: 41
- Joined: Sun Feb 10, 2008 3:32 pm
- Zip Code: 47960
- Tractors Owned: 1948 C
1941 A
1971 JD 110 - Location: IN, Monticello
Re: 1941 A-How many lbs. psi on compression test?
With my screwed up method of checking compression I got 46 to 48 lbs. on all the cylinders. I didn't think that sounded like much pressure.
Steve
Steve
-
- Cub Pro
- Posts: 23701
- Joined: Sun Feb 02, 2003 2:09 pm
- Zip Code: 63664
- Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
- Location: Mo, Potosi
Re: 1941 A-How many lbs. psi on compression test?
With 46 to 48 pounds of compression it should barely be able to move itself, and blow a lot of oil smoke.
If you are not part of the solution,
you are part of the problem!!!
you are part of the problem!!!
-
- Team Cub Mentor
- Posts: 20395
- Joined: Fri Jul 02, 2004 9:52 pm
- Zip Code: 65051
- Circle of Safety: Y
- Location: Mo. Linn
Re: 1941 A-How many lbs. psi on compression test?
Time for a dry and wet compression test. You do not need one of the mechanics quality testers - one of the cheaper ones will do just as well - provide you with the needed information.
NAPA has loaner tools. Perhaps some of the other autoparts store have loaner tools. Know a local mechanic?
NAPA has loaner tools. Perhaps some of the other autoparts store have loaner tools. Know a local mechanic?
I have an excuse. CRS.
-
- Cub Pro
- Posts: 2461
- Joined: Mon Feb 17, 2003 7:53 am
- Zip Code: 47906
- eBay ID: steveb05
- Tractors Owned: 1947 in well used condition
1948 restored
Nice original 1950 just out of the Demo Range
628 2 wheel Trailer
1950 Demo
Tryke
Rat Cub - Circle of Safety: Y
- Location: IN West Lafayette
Re: 1941 A-How many lbs. psi on compression test?
Steve,Stop by and pick up my Compression tester so you can get some accurate reading .
Be prepared to be unprepared Seth Goden
-
- 10+ Years
- Posts: 719
- Joined: Thu Oct 23, 2008 2:38 pm
- Zip Code: 77802
- eBay ID: ronnyb.east.texas
- Tractors Owned: 1938 Farmall F-20
Grandpa's '49 Cub #82289
194x Gibson Model D
1953 Allis Chalmers CA - Location: TX, Bryan
Re: 1941 A-How many lbs. psi on compression test?
John *.?-!.* cub owner wrote:With 46 to 48 pounds of compression it should barely be able to move itself, and blow a lot of oil smoke.
I'm taking it that these are bad numbers, but is there any reason why all four would give reading so similar?
Steve didn't say if these were wet or dry tests, but are these numbers way out of spec for a dry test?
I can understand low readings on a couple of cyinders, but the part about all of them being so close is confusing.
The only thing I can think of is using electrical tape to seal the spark plug openings gave artificially low numbers, and the true compression is a lot higher.
What do y'all think?
Steve, if you are able to get a gauge that fits, please let us know what results you get.
I've got a feeling he has good compression on all four cylinders, but I am definitely not a mechanic!
Ronny
“If it ain’t broke, I haven’t 'fixed' it yet”
“If it ain’t broke, I haven’t 'fixed' it yet”
-
- Team Cub Mentor
- Posts: 20395
- Joined: Fri Jul 02, 2004 9:52 pm
- Zip Code: 65051
- Circle of Safety: Y
- Location: Mo. Linn
Re: 1941 A-How many lbs. psi on compression test?
Could be a couple of reasons that the compression numbers are so similar. My thought is that the electrical tape is a big part of the problem. Also, that the true compression readings - dry then wet will be higher.I'm taking it that these are bad numbers, but is there any reason why all four would give reading so similar?
The only thing I can think of is using electrical tape to seal the spark plug openings gave artificially low numbers, and the true compression is a lot higher.
I've got a feeling he has good compression on all four cylinders.
The fact that the current compression numbers are "even" is a good thing. If the results from the full compression test result in low "even" numbers - then I would suggest starting the engine and operating for a while (a number of hours). Adding Seafoam to the crankcase and gasoline. See what happens.
I have an excuse. CRS.
-
- 10+ Years
- Posts: 41
- Joined: Sun Feb 10, 2008 3:32 pm
- Zip Code: 47960
- Tractors Owned: 1948 C
1941 A
1971 JD 110 - Location: IN, Monticello
Re: 1941 A-How many lbs. psi on compression test?
I should add a couple of hints to this mystery. The engine is hanging on my engine stand and I was cranking it by hand with crank. This was a dry test.
I am going to test it again tomorrow with the correct adapter on a compression gauge and I'll squirt some oil in the cylinders and do it again. I'll fill you in on the results after I'm done.
Steve
I am going to test it again tomorrow with the correct adapter on a compression gauge and I'll squirt some oil in the cylinders and do it again. I'll fill you in on the results after I'm done.
Steve
-
- Cub Pro
- Posts: 23701
- Joined: Sun Feb 02, 2003 2:09 pm
- Zip Code: 63664
- Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
- Location: Mo, Potosi
Re: 1941 A-How many lbs. psi on compression test?
hook up a battery and starter, hand cranking turns it to slow.
If you are not part of the solution,
you are part of the problem!!!
you are part of the problem!!!
-
- Cub Pro
- Posts: 1871
- Joined: Sun Mar 30, 2003 10:25 am
- Zip Code: 06457
- eBay ID: cmtelephone
- Tractors Owned: Restored: 1950 Cub, 1950 Cub Demo, 1948 super AI, 1935 Silver King, 1946 Oliver 60 RC, John Deere M, 1950 C demo.
In working clothes:
1950 cub, 1948 cub, 1941 A, 1948 H, 1963 B414, 1958 240U, 1947 Oliver 60 industrial, Oliver 70 industrial. IH 450, 1963, another 1948 cub, 1946 I6 with Trogan front blade. - Location: CT, Middletown
Re: 1941 A-How many lbs. psi on compression test?
battery crank compression test, for sure. but with the motor already in a stand, i would not hesitate to look inside and see what's up. where you stop depends on what you find and if your block can be welded.
'If they're tappin', they're not burnin'
http://www.ZagrayFarmMuseum.org
http://www.ZagrayFarmMuseum.org
-
- Similar Topics
- Replies
- Views
- Last post
-
-
Compression test C113 engine
by 48SuperAIndustrial » Sat Sep 02, 2023 11:53 am » in Farmall A, Super A, AV, 100, 130 & 140 - 10
- 1336
-
by 48SuperAIndustrial
Sun Sep 03, 2023 6:52 pm
-
-
- 4
- 394
-
by Eugene
Fri Jul 02, 2021 8:16 pm
Return to “Farmall A, Super A, AV, 100, 130 & 140”
Who is online
Users browsing this forum: dgrapes59 and 1 guest