Taking the crankshaft to the machine shop tomorrow for the regrind. This crankshaft came from a stuck engine, and there is a fair bit of out of round, cross taper, and general gouging and lines.
I've miked the main and rod journals, and while the mains will be fine at a .010" undergrind, one rod journal might be close. 010" under are the only rod bearings I have found so far. Looking for suggestions in case anyone knows of a source for .020" rod inserts. Otherwise, I'll have it ground to .010 under and take a look. I'd hate to have to spray it up to get to .010" under!
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Rod bearing question
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 42
- Joined: Sat Jul 10, 2004 9:31 pm
- Location: Tallahassee, FL
Rod bearing question
Frank-in-Tallahassee
'56 JD 70D // '90 JD 855 // '50 Case VAC // '48 IHC Cub "Boo-Boo" // '41 JD "H"
http://www.fboerger.com
F-I-T's webpage.....ALWAYS under construction !!!
'56 JD 70D // '90 JD 855 // '50 Case VAC // '48 IHC Cub "Boo-Boo" // '41 JD "H"
http://www.fboerger.com
F-I-T's webpage.....ALWAYS under construction !!!
-
- Cub Pro
- Posts: 23701
- Joined: Sun Feb 02, 2003 2:09 pm
- Zip Code: 63664
- Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
- Location: Mo, Potosi
-
- 10+ Years
- Posts: 80
- Joined: Sat Feb 08, 2003 11:23 am
- Location: Columbus, Georgia
-
- 10+ Years
- Posts: 42
- Joined: Sat Jul 10, 2004 9:31 pm
- Location: Tallahassee, FL
Well, I looked a bit farther and this site says they have STD, .002, .010, .020, and .030, Rods, and Mains, so I shouldn't have a problem getting a set.
Thanks!
http://www.trustytractor.com/trustytractor/c60enbese.html
Thanks!
http://www.trustytractor.com/trustytractor/c60enbese.html
Frank-in-Tallahassee
'56 JD 70D // '90 JD 855 // '50 Case VAC // '48 IHC Cub "Boo-Boo" // '41 JD "H"
http://www.fboerger.com
F-I-T's webpage.....ALWAYS under construction !!!
'56 JD 70D // '90 JD 855 // '50 Case VAC // '48 IHC Cub "Boo-Boo" // '41 JD "H"
http://www.fboerger.com
F-I-T's webpage.....ALWAYS under construction !!!
-
- Similar Topics
- Replies
- Views
- Last post
-
- 3
- 194
-
by cubbrian
Thu Sep 23, 2021 5:53 am
-
-
Rear input shaft bearing shields-- question Attachment(s)
by Bob McCarty » Wed Jan 03, 2024 7:43 pm » in Farmall Cub - 2
- 709
-
by Bob McCarty
Thu Jan 04, 2024 6:21 pm
-
-
- 1
- 178
-
by Dale Finch
Wed Jun 02, 2021 8:27 pm
-
-
Cub pitman replacement bearing. Attachment(s)
by Stevetractor » Mon May 17, 2021 12:48 pm » in Farmall Cub - 0
- 194
-
by Stevetractor
Mon May 17, 2021 12:48 pm
-
-
- 19
- 1187
-
by indy61
Mon Oct 04, 2021 1:53 pm
Who is online
Users browsing this forum: No registered users and 6 guests