I thought I would post a picture of what a good tooth pattern looks like. If you replace the ring and pinion, you need to check the set up with marking compound.
I replaced the entire gear set from another box, in this case a Cub Cadet, so I was starting from scratch. The goal was to keep the original casting date transmission with the tractor
To do this set up the ring and pinion with the as close to the original shims as possible and measure the backlash in the ring gear. Use your hand in the transmission to lock it in place as you don't want any slop when you rock the ring gear. You are looking for .002 to .005 so you need a dial indicator.
If the lash looks good, then mark the pattern by painting a few of the teeth on the ring gear and with one hand put some drag on the ring gear and then rotate the transmission for several revolutions. If the pattern is in the middle, like this you are good to go. If this pattern was on the top of the tooth, as this one was, then the pinion needs to move back, so a shim needs to come out of the pinion shaft at the front of the box. Then you need to re-set your lash. Assuming your preload was properly set up, you need to remove a shim from the right and put it in the left side to loosen the lash. Once the preload is set you can move shims from one side to the other but you can't remove any shims.
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Differential set up & tooth pattern
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- Team Cub Mentor
- Posts: 6018
- Joined: Thu Jun 07, 2007 9:34 am
- Zip Code: 06040
- Tractors Owned: 77 Cub (red); 74 Cub; 52 Cub; 50 Cub ( post-demo)
- Circle of Safety: Y
- Location: CT, Manchester
-
- 10+ Years
- Posts: 3414
- Joined: Sat May 15, 2004 11:10 am
- Zip Code: 49229
- Location: MI, Britton
Re: Differential set up & tooth pattern
Great job Bob
It takes time and patience to get it right.
Billy
It takes time and patience to get it right.
Billy
Take care of your equipment and it will take care of you. 1964 cub. Farmall 100 and 130.
"Those that say it can’t be done should not interrupt the ones who are doing it.”
"Those that say it can’t be done should not interrupt the ones who are doing it.”
-
- 10+ Years
- Posts: 1968
- Joined: Fri Dec 26, 2008 9:28 pm
- Zip Code: 93313
- Location: CA, Bakersfield
Re: Differential set up & tooth pattern
Very well done......should last another 6o years....
Robert (never done that job) Miller
Robert (never done that job) Miller
-
- Cub Pro
- Posts: 10290
- Joined: Mon Oct 24, 2005 8:35 pm
- Zip Code: 23962
- eBay ID: dmb2613
- Circle of Safety: Y
- Location: VA. Randolph
Re: Differential set up & tooth pattern
Just to add one thought, if you are using old gears, if at all possible use the same shims that the gears came with. The gears will be worn to riding in a certain place. If you have to use different shims you stand the possibility of having some gear noise.
just because the bears are meshing good that does not mean they were riding in the same place originally. Most of the time if it has noise from this issue it will be in high gear when the ring and pinion are turning the fastest.
Boss
just because the bears are meshing good that does not mean they were riding in the same place originally. Most of the time if it has noise from this issue it will be in high gear when the ring and pinion are turning the fastest.
Boss
IN GOD WE TRUST
All others pay cash
Boss Hog
Power corrupts; absolute power corrupts absolutely byJohn Emerich Edward Dalberg
All others pay cash
Boss Hog
Power corrupts; absolute power corrupts absolutely byJohn Emerich Edward Dalberg
-
- Team Cub Mentor
- Posts: 6018
- Joined: Thu Jun 07, 2007 9:34 am
- Zip Code: 06040
- Tractors Owned: 77 Cub (red); 74 Cub; 52 Cub; 50 Cub ( post-demo)
- Circle of Safety: Y
- Location: CT, Manchester
Re: Differential set up & tooth pattern
In my case the gear set came from another casting and I did not take it apart. If I had, I would have measured the lash and tooth pattern before it came apart to try to duplicate it. I think the gears and bearings are made to a high tolerance and the variation is probably coming out of the machining of the casting. So you probably want the shims to follow the case as a baseline but the lash and tooth pattern from the donor gear set. If that makes sense.
-
- Similar Topics
- Replies
- Views
- Last post
-
- 19
- 479
-
by outdoors4evr
Fri Jun 16, 2023 1:32 pm
-
- 0
- 109
-
by goxu1
Tue Jan 23, 2024 2:36 am
-
-
Harvest King rear tractor tires and tread pattern? Attachment(s)
by Super A » Tue May 24, 2022 6:15 am » in Farmall Cub - 38
- 1592
-
by tldec50
Sun Jun 19, 2022 6:26 pm
-
-
- 0
- 157
-
by baldwindiesel
Thu Jan 12, 2023 12:00 pm
-
- 0
- 88
-
by baldwindiesel
Thu Jun 22, 2023 9:27 am
Who is online
Users browsing this forum: No registered users and 2 guests