Bought this at the I & I tractor show !
Left side
Right side
I was hoping it was a 153 cuin motor that would fit my 504 tractor,---BUT its a 200 cuin!---anybody got an idea what the 200 was used on?---this has the bellhousing tag torn off, and has some brackets bolted on both ends like for power unit use.
My IH info kinda runs out at 153,--I really could use some help figuring this one out, AND if it might just still fit the 504! thanks; sonny
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
IH engine
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 4117
- Joined: Thu Nov 09, 2006 11:26 pm
- Zip Code: 61722
-
- 10+ Years
- Posts: 2917
- Joined: Sat Feb 11, 2006 5:26 pm
- Location: NC
Re: IH engine
I do not know first hand anything about that engine. Assuming that the identification of size is correct, the engine is used in various applications and has different configurations depending on application.
(1) 544, 2544, 8000 fork lift with synchromesh transmission. (2) 544, 2544 with hydrostatic. (3) 574, 2500A, 2500B, 2505B, 2510B, 2514B synchromesh. (4)574, 2500A, 2500B, 2505B, 25101B, 2514B hydrostatic, 674 synchromesh. (5) 3500A.
(1) 544, 2544, 8000 fork lift with synchromesh transmission. (2) 544, 2544 with hydrostatic. (3) 574, 2500A, 2500B, 2505B, 2510B, 2514B synchromesh. (4)574, 2500A, 2500B, 2505B, 25101B, 2514B hydrostatic, 674 synchromesh. (5) 3500A.
Luck favors those who are prepared
-
- 10+ Years
- Posts: 2917
- Joined: Sat Feb 11, 2006 5:26 pm
- Location: NC
Re: IH engine
Does the paint color of that engine suggest a forklift? Parts lists for that engine are in parts catalog ENG-1.
Luck favors those who are prepared
-
- 10+ Years
- Posts: 4117
- Joined: Thu Nov 09, 2006 11:26 pm
- Zip Code: 61722
Re: IH engine
The paint layer underneath is red primer and the color coat is IH industrial yellow!
I took the head off today and got the motor un-stuck,---looks decent inside, just needs new rings,---pistons have a little slap in the bores! ---pics to follow! thanks; sonny
I took the head off today and got the motor un-stuck,---looks decent inside, just needs new rings,---pistons have a little slap in the bores! ---pics to follow! thanks; sonny
-
- 10+ Years
- Posts: 4117
- Joined: Thu Nov 09, 2006 11:26 pm
- Zip Code: 61722
Re: IH engine
Motor has this stamped on the machined boss---200 CU 2U 04 2535 ---- casting # 397974 R1---right rear boss has F B 8 5 stamped on it. date code is 10. 31. Y
closeup of #3 piston top
Motor un-sticker set (oak 2x4, and BIG hammer)
The dirty head lots of carbon build-up on the inside, needs rings
Top of block after I got it unstuck and cleaned
#1 cylinder after I cleaned it up!--It was the worst stuck one
After driving the piston #1 down to bottom of bore I ran a stiff rotary wire brush up and down the wall, then ran this hone in there a few strokes to smooth up the missed nasties then cleaned the bore before turning over with starter
The manifold has the front ear broke off and 1 bolt broke off too
This is kinda how ya unstick motors around here! LOL!!! thanks; sonny
closeup of #3 piston top
Motor un-sticker set (oak 2x4, and BIG hammer)
The dirty head lots of carbon build-up on the inside, needs rings
Top of block after I got it unstuck and cleaned
#1 cylinder after I cleaned it up!--It was the worst stuck one
After driving the piston #1 down to bottom of bore I ran a stiff rotary wire brush up and down the wall, then ran this hone in there a few strokes to smooth up the missed nasties then cleaned the bore before turning over with starter
The manifold has the front ear broke off and 1 bolt broke off too
This is kinda how ya unstick motors around here! LOL!!! thanks; sonny
-
- Similar Topics
- Replies
- Views
- Last post
-
- 10
- 1834
-
by SONNY
Thu Jun 24, 2021 2:57 pm
Return to “Farmall / IH / CASE”
Who is online
Users browsing this forum: No registered users and 2 guests