This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
removal of transmission input shaft 154 lo boy
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 957
- Joined: Tue Dec 18, 2007 8:18 pm
- Zip Code: 55325
- Tractors Owned: 1958 ih 340 utility
1950 farmall cub
1948 ford 8n
kubota 3240
IH 154 loboy - Location: Dassel, Minnesota
removal of transmission input shaft 154 lo boy
decided to remove the bad input shaft, Clutch and sheet metal was already off . Next I removed top gear shift lever and cover (8) bolts exposing the shifter forks, rods input shaft and gears.see pic 1. Next i removed rear differential cover (9) bolts ,exposing the rear of the input shaft and left and right shifter rods.see. pic 2 Next I removed the 2 shifter fork set screws/bolts, make sure you are in neutral first. see pic 3. Next go to rear access of differential housing, and I used a piece of steel rod I had on hand, used a light hammer to drive forward shifter rods, take your time, and tap the rods out, you will drive rods through front of transmission housing, the frost plugs will drive out as rod is moved forward and out of transmission housing, be careful of shifter forks as rods move through and remove forks once rod is clear. Cover rod bores with your hand or have someone assist you, make sure not to lose the spring or ball that seats inside rod bore, as rod exits bore ,the spring and ball may release with enough pressure to go flying if bore is not covered with hand.see pic 4. Next I removed clutch shaft oil seal, and through rear access of differential housing I used the same rod for for tapping out shifter rods,to tap out input shaft. As input shaft is moved forward, slowly tap until shaft has mostly cleared rear needle bearing , be careful not to damage bearing, remove gears as shaft exits transmission housing. see pic 5 and 6 This was my first time removing a input shaft, and the job did not take long, about a 1hour. I did already have sheet metal and clutch removed, or this would have taken a few hours more. Thanks Hamilton Bob for your guidance.
-
- 10+ Years
- Posts: 957
- Joined: Tue Dec 18, 2007 8:18 pm
- Zip Code: 55325
- Tractors Owned: 1958 ih 340 utility
1950 farmall cub
1948 ford 8n
kubota 3240
IH 154 loboy - Location: Dassel, Minnesota
Re: removal of transmission input shaft 154 lo boy
location of springs and shifter poppet ball, left and right side shifter rod bores
-
- 10+ Years
- Posts: 7153
- Joined: Sat Feb 18, 2006 8:12 pm
- Zip Code: 15101
- eBay ID: lacrosseorgans
- Skype Name: Mike.Hengelsberg
- Tractors Owned: 1949 Cub "Merlin"
1955 Cub "Lewis"
Cub Trailer
A-60 Blade
Cub-22 Mower
193 Plow - Circle of Safety: Y
- Location: PA, Allison Park (Am Hengelsberg)
Re: removal of transmission input shaft 154 lo boy
Hey Jim...
You going to try to make it to the Cheesy Fest this year??
Mike in La Crosse, WI
You going to try to make it to the Cheesy Fest this year??
Mike in La Crosse, WI
-
- 10+ Years
- Posts: 957
- Joined: Tue Dec 18, 2007 8:18 pm
- Zip Code: 55325
- Tractors Owned: 1958 ih 340 utility
1950 farmall cub
1948 ford 8n
kubota 3240
IH 154 loboy - Location: Dassel, Minnesota
Re: removal of transmission input shaft 154 lo boy
Mike , very possible I can make it this year. hopefully everything works out this year, I need to meet you all and support a great group . will let you know as time gets closer to the date.
-
- 10+ Years
- Posts: 188
- Joined: Wed Sep 03, 2008 4:35 pm
- Zip Code: 07869
- Location: Randolph, NJ
Re: removal of transmission input shaft 154 lo boy
JG,
"Thank You" - VERY MUCH for all the GREAT pictures !!!!
I have been keeping a 'pictionary' of many parts and procedures on the numbered series cubs and this make a very fine addition to the Transmission Maintenance Section.
Thanks again, NJDale
"Thank You" - VERY MUCH for all the GREAT pictures !!!!
I have been keeping a 'pictionary' of many parts and procedures on the numbered series cubs and this make a very fine addition to the Transmission Maintenance Section.
Thanks again, NJDale
-
- 10+ Years
- Posts: 957
- Joined: Tue Dec 18, 2007 8:18 pm
- Zip Code: 55325
- Tractors Owned: 1958 ih 340 utility
1950 farmall cub
1948 ford 8n
kubota 3240
IH 154 loboy - Location: Dassel, Minnesota
Re: removal of transmission input shaft 154 lo boy
your welcome . I have used pictures that others have posted several times on repairs , and sometimes pictures can make all the difference for a smooth going repair. Jim
-
- 10+ Years
- Posts: 1
- Joined: Sun Jul 31, 2011 1:12 am
- Zip Code: 27107
Re: removal of transmission input shaft 154 lo boy
JGTools thank you a thousand times over. Have a 154 and needed to replace a shifter fork and didn't know how to get the rods out! Can't state enough how extremely appreciative I am of your post/pictures.
Had the 1st/R gear push out of the shifter fork, the gear pushed itself though and would no longer go into reverse since it had 1/2" extra play in it.
Had the 1st/R gear push out of the shifter fork, the gear pushed itself though and would no longer go into reverse since it had 1/2" extra play in it.
-
- Similar Topics
- Replies
- Views
- Last post
-
-
154, transmission input shaft
by Duner » Tue Feb 15, 2022 8:10 pm » in Lo-Boy Series - 154, 184, 185 - 0
- 290
-
by Duner
Tue Feb 15, 2022 8:10 pm
-
-
-
PTO Shaft Removal on 184
by JacktheWindy » Mon Aug 28, 2023 9:42 pm » in Lo-Boy Series - 154, 184, 185 - 0
- 828
-
by JacktheWindy
Mon Aug 28, 2023 9:42 pm
-
-
-
Steering shaft removal 185
by Bronccat » Tue Jun 01, 2021 6:01 pm » in Lo-Boy Series - 154, 184, 185 - 9
- 649
-
by Bronccat
Sat Jun 05, 2021 9:39 am
-
-
-
IH 154 PTO shaft Bearing
by yellowcub » Fri May 03, 2024 11:49 am » in Lo-Boy Series - 154, 184, 185 - 1
- 73
-
by SONNY
Wed May 08, 2024 10:32 am
-
-
-
Steering Shaft Attachment(s)
by Ridgefield » Wed Aug 31, 2022 8:23 am » in Lo-Boy Series - 154, 184, 185 - 11
- 375
-
by Duner
Sat Sep 03, 2022 8:44 am
-
Return to “Lo-Boy Series - 154, 184, 185”
Who is online
Users browsing this forum: No registered users and 1 guest